Andrzej Dziadoń
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Andrzej Dziadoń has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Renata Mola
Faculty of Mechatronics and Mechanical Engineering, Kielce University of Technology, Al. Tysiąclecia P.P. 7, 25-314 Kielce, Poland
6 shared publications - Tomasz Bucki
Kielce University of Technology, Kielce, Poland, EU
3 shared publications E. Musiał
Kielce University of Technology, Metals Science and Materials Technologies, 7 Tysiąclecia Państwa Polskiego Av., 25-314, Kielce, Poland
2 shared publicationsAndrzej Latkowski
1 shared publicationJan Wesolowski
1 shared publication- Karina Jagielska-Wiaderek
Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, 42-201 Czestochowa, Poland
1 shared publication
Latest Publications
- 10 June 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 67 (2) , 435-440
Effects of Post-Weld Heat Treatment on the Microstructure and Mecanical Properties of the AZ91 Laser Welded Joint
Plates of AZ91 magnesium alloy were butt-welded using a CO2 laser. The non-equilibrium solidification of the laser-melted metal caused fragmentation of the weld microstructure as well as the supersaturation of a solid solution of aluminium in magnesium, which enabled the T5 ageing of the weld. The weld proved to be a mechanically stable part of the joint; all the tensile-tested specimens, both as-welded and post-weld T5 aged, fractured outside it. During the ageing of the supersaturated joint, which involved heat treating it to the T6 condition, the weld was the region where discontinuous precipitation was observed and this was the location of fracture in the tensile specimens. Thus, the strength properties of welded, supersaturated and aged AZ91 were much worse than when the non-welded material was T6 tempered.
- 10 June 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 67 (2) , 435-440
Effects of Post-Weld Heat Treatment on the Microstructure and Mecanical Properties of the AZ91 Laser Welded Joint
Plates of AZ91 magnesium alloy were butt-welded using a CO2 laser. The non-equilibrium solidification of the laser-melted metal caused fragmentation of the weld microstructure as well as the supersaturation of a solid solution of aluminium in magnesium, which enabled the T5 ageing of the weld. The weld proved to be a mechanically stable part of the joint; all the tensile-tested specimens, both as-welded and post-weld T5 aged, fractured outside it. During the ageing of the supersaturated joint, which involved heat treating it to the T6 condition, the weld was the region where discontinuous precipitation was observed and this was the location of fracture in the tensile specimens. Thus, the strength properties of welded, supersaturated and aged AZ91 were much worse than when the non-welded material was T6 tempered.
- 6 May 2020
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 20 (3) , 9-14
Structure and Mechanical Properties of the CO2 Laser Welded Joint of AZ91 Cast Magnesium Alloy
- 6 May 2020
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 20 (3) , 9-14
Structure and Mechanical Properties of the CO2 Laser Welded Joint of AZ91 Cast Magnesium Alloy
- Open Access
- 1 March 2017
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 17 (1) , 202-206
Microstructure of the Bonding Zone Between AZ91 and AlSi17 Formed by Compound Casting
This paper discusses the joining of AZ91 magnesium alloy with AlSi17 aluminium alloy by compound casting. Molten AZ91 was cast at 650°C onto a solid AlSi17 insert placed in a steel mould under normal atmospheric conditions. Before casting, the mould with the insert inside was heated up to about 370°C. The bonding zone forming between the two alloys because of diffusion had a multiphase structure and a thickness of about 200 μm. The microstructure and composition of the bonding zone were analysed using optical microscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy. The results indicate that the bonding zone adjacent to the AlSi17 alloy was composed of an Al3Mg2intermetallic phase with not fully consumed primary Si particles, surrounded by a rim of an Mg2Si intermetallic phase and fine Mg2Si particles. The bonding zone near the AZ91 alloy was composed of a eutectic (an Mg17Al12intermetallic phase and a solid solution of Al and Si in Mg). It was also found that the compound casting process slightly affected the AZ91 alloy microstructure; a thin layer adjacent to the bonding zone of the alloy was enriched with aluminium.
- 1 March 2017
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 17 (1) , 202-206
Open AccessMicrostructure of the Bonding Zone Between AZ91 and AlSi17 Formed by Compound Casting
This paper discusses the joining of AZ91 magnesium alloy with AlSi17 aluminium alloy by compound casting. Molten AZ91 was cast at 650°C onto a solid AlSi17 insert placed in a steel mould under normal atmospheric conditions. Before casting, the mould with the insert inside was heated up to about 370°C. The bonding zone forming between the two alloys because of diffusion had a multiphase structure and a thickness of about 200 μm. The microstructure and composition of the bonding zone were analysed using optical microscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy. The results indicate that the bonding zone adjacent to the AlSi17 alloy was composed of an Al3Mg2intermetallic phase with not fully consumed primary Si particles, surrounded by a rim of an Mg2Si intermetallic phase and fine Mg2Si particles. The bonding zone near the AZ91 alloy was composed of a eutectic (an Mg17Al12intermetallic phase and a solid solution of Al and Si in Mg). It was also found that the compound casting process slightly affected the AZ91 alloy microstructure; a thin layer adjacent to the bonding zone of the alloy was enriched with aluminium.
- Open Access
- 1 February 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 179 (1) , 012053
Effects of the pouring temperature on the formation of the bonding zone between AZ91 and AlSi17 in the compound casting process
The compound casting process was used to join AZ91 magnesium alloy to AlSi17 aluminium alloy. Liquid AZ91 was poured onto a solid AlSi17 insert placed in a steel mould heated to 370 °C. The experimental results showed that the temperature of the AZ91 melt affected the formation of the bonding zone between the two alloys. A continuous bonding zone was formed by applying a pouring temperature of 650 °C. The use of higher temperatures, i.e. 680 °C and 700 °C, did not lead to the formation of a continuous metallurgical transition zone at the AZ91/AlSi17 interface. The bonding zone was analysed using an optical microscope and a scanning electron microscope equipped with an energy dispersive X-ray (EDS) detector. The structural constituents of the bonding zone near the AlSi17 alloy were: an Al3Mg2 intermetallic phase, primary Si particles surrounded by a rim of an Mg2Si intermetallic phase and fine Mg2Si particles. The area of the bonding zone that was adjacent to the AZ91 alloy had a eutectic structure composed of an Mg17Al12 intermetallic phase and a solid solution of Al and Si in Mg.
- 1 February 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 179 (1) , 012053
Open AccessEffects of the pouring temperature on the formation of the bonding zone between AZ91 and AlSi17 in the compound casting process
The compound casting process was used to join AZ91 magnesium alloy to AlSi17 aluminium alloy. Liquid AZ91 was poured onto a solid AlSi17 insert placed in a steel mould heated to 370 °C. The experimental results showed that the temperature of the AZ91 melt affected the formation of the bonding zone between the two alloys. A continuous bonding zone was formed by applying a pouring temperature of 650 °C. The use of higher temperatures, i.e. 680 °C and 700 °C, did not lead to the formation of a continuous metallurgical transition zone at the AZ91/AlSi17 interface. The bonding zone was analysed using an optical microscope and a scanning electron microscope equipped with an energy dispersive X-ray (EDS) detector. The structural constituents of the bonding zone near the AlSi17 alloy were: an Al3Mg2 intermetallic phase, primary Si particles surrounded by a rim of an Mg2Si intermetallic phase and fine Mg2Si particles. The area of the bonding zone that was adjacent to the AZ91 alloy had a eutectic structure composed of an Mg17Al12 intermetallic phase and a solid solution of Al and Si in Mg.
- 1 August 2016
- Published by Elsevier in Materials Characterization
- Vol. 118, 505-513
The microstructure of the surface layer of magnesium laser alloyed with aluminum and silicon
- 1 August 2016
- Published by Elsevier in Materials Characterization
- Vol. 118, 505-513
The microstructure of the surface layer of magnesium laser alloyed with aluminum and silicon
- 30 June 2016
- Published by SAGE Publications in Surface Engineering
- Vol. 32 (12) , 908-915
Properties of Mg laser alloyed with Al or AlSi20
The alloyed surface layers were produced using thin Al or AlSi20 plates, which were first diffusion bonded and then melted into the Mg substrate. The microscopic analysis showed that alloying with Al led to the formation of an Al-enriched surface layer containing a high volume fraction of an Mg17Al12 phase. Applying AlSi20, on the other hand, resulted in the formation of an Al/Si-enriched layer containing Mg2Si, Mg2Al3 and Mg17Al12 phases. The experimental results indicate that surface alloying of Mg with Al or AlSi20 using the presented method improved the properties of the material. The microhardness of the Al- and Al/Si-enriched layers was much higher than that of the substrate. Higher wear resistance was observed for the Al/Si-enriched layer. The alloyed layers provided a certain level of protection of Mg against corrosion. The specimens alloyed with Al showed better anticorrosive properties than those alloyed with AlSi20.
- 30 June 2016
- Published by SAGE Publications in Surface Engineering
- Vol. 32 (12) , 908-915
Properties of Mg laser alloyed with Al or AlSi20
The alloyed surface layers were produced using thin Al or AlSi20 plates, which were first diffusion bonded and then melted into the Mg substrate. The microscopic analysis showed that alloying with Al led to the formation of an Al-enriched surface layer containing a high volume fraction of an Mg17Al12 phase. Applying AlSi20, on the other hand, resulted in the formation of an Al/Si-enriched layer containing Mg2Si, Mg2Al3 and Mg17Al12 phases. The experimental results indicate that surface alloying of Mg with Al or AlSi20 using the presented method improved the properties of the material. The microhardness of the Al- and Al/Si-enriched layers was much higher than that of the substrate. Higher wear resistance was observed for the Al/Si-enriched layer. The alloyed layers provided a certain level of protection of Mg against corrosion. The specimens alloyed with Al showed better anticorrosive properties than those alloyed with AlSi20.
- Open Access
- 1 March 2016
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 16 (1) , 112-116
Formation of Al-alloyed Layer on Magnesium with Use of Casting Techniques
Al-enriched layer was formed on a magnesium substrate with use of casting. The magnesium melt was cast into a steel mould with an aluminium insert placed inside. Different conditions of the casting process were applied. The reaction between the molten magnesium and the aluminium piece during casting led to the formation of an Al-enriched surface layer on the magnesium substrate. The thickness of the layer was dependent on the casting conditions. In all fabricated layers the following phases were detected: a solid solution of Mg in Al, Al3Mg2, Mg17Al12 and a solid solution of Mg in Al. When the temperature of the melt and the mould was lower (variant 1 – 670°C and 310°; variant 2 – 680°C and 310°C, respectively) the unreacted thin layer of aluminium was observed in the outer zone. Applying higher temperatures of the melt (685°C) and the mould (325°C) resulted in deep penetration of aluminium into the magnesium substrate. Areas enriched in aluminium were locally observed. The Al-enriched layers composed mainly of Mg-Al intermetallic phases have hardness from 187-256 HV0.1.
- 1 March 2016
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 16 (1) , 112-116
Open AccessFormation of Al-alloyed Layer on Magnesium with Use of Casting Techniques
Al-enriched layer was formed on a magnesium substrate with use of casting. The magnesium melt was cast into a steel mould with an aluminium insert placed inside. Different conditions of the casting process were applied. The reaction between the molten magnesium and the aluminium piece during casting led to the formation of an Al-enriched surface layer on the magnesium substrate. The thickness of the layer was dependent on the casting conditions. In all fabricated layers the following phases were detected: a solid solution of Mg in Al, Al3Mg2, Mg17Al12 and a solid solution of Mg in Al. When the temperature of the melt and the mould was lower (variant 1 – 670°C and 310°; variant 2 – 680°C and 310°C, respectively) the unreacted thin layer of aluminium was observed in the outer zone. Applying higher temperatures of the melt (685°C) and the mould (325°C) resulted in deep penetration of aluminium into the magnesium substrate. Areas enriched in aluminium were locally observed. The Al-enriched layers composed mainly of Mg-Al intermetallic phases have hardness from 187-256 HV0.1.
- Open Access
- 1 September 2011
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 56 (3) , 677-684
Formation of Layered Mg/Eutectic Composite Using Diffusional Processes at the Mg-Al Interface
Formation of Layered Mg/Eutectic Composite Using Diffusional Processes at the Mg-Al Interface: A processing technique has been developed to produce a layered magnesium-intermetallic compound light composite from elemental magnesium and aluminium sheets. Structural examination and measurements of transition layer grown at the magnesium-aluminium interface at high annealing temperature were performed. It was found using Mg/Al diffusion couple that solid state diffusion results in development of Al3Mg2and Mg17Al12intermetallic compounds, which are separated into two sublayers. The rate of the layer growth substantially increases with the appearance of the liquid phase at the Mg-Al interface. The microstructure resulted from the partial solidification contains an eutectic composed of Mg17Al12intermetallic compound and solid solution aluminium in magnesium. The structural processes, which transform the magnesium-aluminium interface, can be applied for fabrication of layered magnesium-eutectic composites. Alternately stacked magnesium and aluminium sheets, formed into a packet, were heated until aluminium was exhausted throughout the course of the Mg-Al reaction with the liquid phase contribution. As a result, the composite containing residual magnesium and layers of eutectic mixture (Mg17Al12and solid solution of aluminium in magnesium) was obtained. Rapid solidification resulted in fine-grained eutectic microstructure development. Using the presented method, composites with required thickness ratio of magnesium and the eutectic layers can be obtained by choosing appropriate thickness ratio of starting magnesium and aluminium sheets.
- 1 September 2011
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 56 (3) , 677-684
Open AccessFormation of Layered Mg/Eutectic Composite Using Diffusional Processes at the Mg-Al Interface
Formation of Layered Mg/Eutectic Composite Using Diffusional Processes at the Mg-Al Interface: A processing technique has been developed to produce a layered magnesium-intermetallic compound light composite from elemental magnesium and aluminium sheets. Structural examination and measurements of transition layer grown at the magnesium-aluminium interface at high annealing temperature were performed. It was found using Mg/Al diffusion couple that solid state diffusion results in development of Al3Mg2and Mg17Al12intermetallic compounds, which are separated into two sublayers. The rate of the layer growth substantially increases with the appearance of the liquid phase at the Mg-Al interface. The microstructure resulted from the partial solidification contains an eutectic composed of Mg17Al12intermetallic compound and solid solution aluminium in magnesium. The structural processes, which transform the magnesium-aluminium interface, can be applied for fabrication of layered magnesium-eutectic composites. Alternately stacked magnesium and aluminium sheets, formed into a packet, were heated until aluminium was exhausted throughout the course of the Mg-Al reaction with the liquid phase contribution. As a result, the composite containing residual magnesium and layers of eutectic mixture (Mg17Al12and solid solution of aluminium in magnesium) was obtained. Rapid solidification resulted in fine-grained eutectic microstructure development. Using the presented method, composites with required thickness ratio of magnesium and the eutectic layers can be obtained by choosing appropriate thickness ratio of starting magnesium and aluminium sheets.
- 15 July 2007
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 460-461, 238-242
Strain behaviour of copper-intermetallic layered composite
- 15 July 2007
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 460-461, 238-242
Strain behaviour of copper-intermetallic layered composite
- 1 February 1996
- Published by Elsevier in Scripta Materialia
- Vol. 34 (3) , 375-380
The effect of grain size on serrated flow of nickel
- 1 February 1996
- Published by Elsevier in Scripta Materialia
- Vol. 34 (3) , 375-380
The effect of grain size on serrated flow of nickel