Pablo Moreno Garibaldi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Pablo Moreno Garibaldi has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Juan Alfonso Beltrán-Fernández
Unidad Profesional Adolfo López Mateos “Zacatenco” Col. Lindavista
10 shared publications - Luis Héctor Hernández-Gómez
Instituto Politécnico Nacional
7 shared publications - Melvyn Alvarez Vera
Departamento de Ingeniería Industrial y Mecánica, Escuela de Ingeniería, Universidad de las Américas Puebla, Ex-Hacienda Santa Catarina Mártir S/N, Puebla 72810, Mexico
5 shared publications - Rafael Carrera-Espinoza
Departamento de Ingeniería Industrial y Mecánica, Universidad de las Américas Puebla, Ex Hacienda Santa Catarina Mártir, San Andrés Cholula 72810, Mexico
5 shared publications - Guillermo Urriolagoitia Calderon
Instituto Politécnico Nacional, Escuela Superior de Ingeniería Mecánica y Eléctrica, Sección de Estudios de Posgrado e Investigación, Unidad Profesional Adolfo López Mateos, Zacatenco
3 shared publications - Héctor Manuel Hernández García
Innovabienestar de México, SAPI de CV, Ciencia y Tecnología No. 790, Col. Saltillo 400, Saltillo 25290, Mexico
3 shared publications
Latest Publications
- Open Access
Controlled Impact Fragmentation of Extracted Teeth as a Novel Strategy for Dentin Graft Preparation: A Granulometric and Comparative Study
Alveolar bone preservation following tooth extraction requires biomaterials with appropriate biological and physical properties. Here, particle size and morphology of the biomaterial play a critical role in bone regeneration. Tooth particle grafts represent a promising alternative because of their compositional similarity to bone; however, current dentin processing methods often lack standardization and produce heterogeneous particle populations. This study evaluated a novel impact-driven fragmentation system designed to produce dentin particles with controlled size distributions through adjustment of a predefined clearance distance. Fresh porcine teeth were fragmented under three operating conditions (250, 300, and 400 µm clearance distances). Particle characterization was performed using scanning electron microscopy (SEM), laser diffraction granulometric analysis, morphometric measurements of particle length and width, descriptive statistical analysis, and linear regression analysis to evaluate dimensional relationships. Laser diffraction analysis demonstrated that increasing clearance distance produced progressively larger particles, with volume mean diameters of 222, 289.6, and 356 µm for the 250, 300, and 400 µm conditions, respectively. The 300 µm condition generated the most homogeneous particle population, exhibiting the lowest span value (0.34) and the narrowest particle size distribution. SEM observations revealed elongated particles with consistent morphology across all conditions. Morphometric analysis confirmed proportional increases in particle length and width with increasing clearance distance, while aspect ratios remained relatively constant (2.02–2.37). Regression analysis showed a positive linear relationship between particle length and width, supporting a common fragmentation mechanism across all operating conditions. Controlled impact fragmentation enables predictable dentin particle production, allowing for particle size regulation through a defined mechanical parameter while preserving particle morphology. The 300 µm clearance condition provided the most favorable balance between particle size control and distribution homogeneity, suggesting that this approach may contribute to the standardized preparation of tooth-derived graft biomaterials for future bone regeneration applications.
Open AccessControlled Impact Fragmentation of Extracted Teeth as a Novel Strategy for Dentin Graft Preparation: A Granulometric and Comparative Study
Alveolar bone preservation following tooth extraction requires biomaterials with appropriate biological and physical properties. Here, particle size and morphology of the biomaterial play a critical role in bone regeneration. Tooth particle grafts represent a promising alternative because of their compositional similarity to bone; however, current dentin processing methods often lack standardization and produce heterogeneous particle populations. This study evaluated a novel impact-driven fragmentation system designed to produce dentin particles with controlled size distributions through adjustment of a predefined clearance distance. Fresh porcine teeth were fragmented under three operating conditions (250, 300, and 400 µm clearance distances). Particle characterization was performed using scanning electron microscopy (SEM), laser diffraction granulometric analysis, morphometric measurements of particle length and width, descriptive statistical analysis, and linear regression analysis to evaluate dimensional relationships. Laser diffraction analysis demonstrated that increasing clearance distance produced progressively larger particles, with volume mean diameters of 222, 289.6, and 356 µm for the 250, 300, and 400 µm conditions, respectively. The 300 µm condition generated the most homogeneous particle population, exhibiting the lowest span value (0.34) and the narrowest particle size distribution. SEM observations revealed elongated particles with consistent morphology across all conditions. Morphometric analysis confirmed proportional increases in particle length and width with increasing clearance distance, while aspect ratios remained relatively constant (2.02–2.37). Regression analysis showed a positive linear relationship between particle length and width, supporting a common fragmentation mechanism across all operating conditions. Controlled impact fragmentation enables predictable dentin particle production, allowing for particle size regulation through a defined mechanical parameter while preserving particle morphology. The 300 µm clearance condition provided the most favorable balance between particle size control and distribution homogeneity, suggesting that this approach may contribute to the standardized preparation of tooth-derived graft biomaterials for future bone regeneration applications.
- Open Access
Tribological Properties of AISI 420 ESR Stainless Steel Modified by Sequential Boriding and Nitriding
This study investigates the effects of surface thermochemical treatments using boriding, nitriding, and boronitriding on the microstructure and mechanical properties of martensitic stainless steel AISI 420 ESR. Powder-pack boriding, gas nitriding, and sequential boronitriding processes were applied to enhance surface hardness, wear resistance, and adhesion. The microstructural and mechanical properties of the surface samples were analyzed using scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, microhardness, and nanoindentation testing. Tribological behavior was analyzed using a pin-on-disk tribometer under dry-sliding wear conditions, with applied normal loads of 5 N and 10 N and a sliding distance of 1000 m. The results showed that the borided samples exhibited the highest surface hardness, up to 1182 HV0.05, as well as brittle fracture and spallation with poor adhesion, while the boronitrided layer offered excellent adhesion. The boronitriding condition demonstrated a synergistic balance, combining high wear resistance (5.92 × 10−7 mm3N−1m−1 and 4.96 × 10−7 mm3N−1m−1) and reduced friction (~0.78 and ~0.67) for loads of 5 N and 10 N, respectively, without brittle fractures on the coating layer. These results confirm that duplex coating treatment is an effective strategy for improving the surface performance of AISI 420 ESR components subjected to severe operating conditions.
Open AccessTribological Properties of AISI 420 ESR Stainless Steel Modified by Sequential Boriding and Nitriding
This study investigates the effects of surface thermochemical treatments using boriding, nitriding, and boronitriding on the microstructure and mechanical properties of martensitic stainless steel AISI 420 ESR. Powder-pack boriding, gas nitriding, and sequential boronitriding processes were applied to enhance surface hardness, wear resistance, and adhesion. The microstructural and mechanical properties of the surface samples were analyzed using scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, microhardness, and nanoindentation testing. Tribological behavior was analyzed using a pin-on-disk tribometer under dry-sliding wear conditions, with applied normal loads of 5 N and 10 N and a sliding distance of 1000 m. The results showed that the borided samples exhibited the highest surface hardness, up to 1182 HV0.05, as well as brittle fracture and spallation with poor adhesion, while the boronitrided layer offered excellent adhesion. The boronitriding condition demonstrated a synergistic balance, combining high wear resistance (5.92 × 10−7 mm3N−1m−1 and 4.96 × 10−7 mm3N−1m−1) and reduced friction (~0.78 and ~0.67) for loads of 5 N and 10 N, respectively, without brittle fractures on the coating layer. These results confirm that duplex coating treatment is an effective strategy for improving the surface performance of AISI 420 ESR components subjected to severe operating conditions.
- Open Access
Study on the Tribological Properties of DIN 16MnCr5 Steel after Duplex Gas-Nitriding and Pack Boriding
DIN 16MnCr5 is commonly used in mechanical engineering contact applications such as gears, joint parts, shafts, gear wheels, camshafts, bolts, pins, and cardan joints, among others. This study examined the microstructural and mechanical properties and tribological behavior of different surface treatments applied to DIN 16MnCr5 steel. The samples were hardened at 870 °C for 15 min and then quenched in water. The surface conditions evaluated were as follows: quenched and tempered DIN 16MnCr5 steel samples without surface treatments (control group), quenched and tempered DIN 16MnCr5 steel samples with gas-nitriding at 560 °C for 6 h, quenched and tempered DIN 16MnCr5 steel samples with pack boriding at 950 °C for 4 h, and quenched and tempered DIN 16MnCr5 steel samples with duplex gas-nitriding and pack boriding. Microstructure characterization was carried out using metallographic techniques, optical microscopy, scanning electron microscopy with energy-dispersive spectroscopy, and X-ray diffraction. The mechanical properties were assessed through microhardness and elastic modulus tests using nanoindentation. The tribological behavior was evaluated using pin-on-disc tests following the ASTM G99-17 standard procedure under dry sliding conditions. The results indicated that the surface treated with duplex gas-nitriding and pack boriding exhibited the highest wear resistance and a reduced coefficient of friction due to improved mechanical properties, leading to increased hardness and elastic modulus.
Open AccessStudy on the Tribological Properties of DIN 16MnCr5 Steel after Duplex Gas-Nitriding and Pack Boriding
DIN 16MnCr5 is commonly used in mechanical engineering contact applications such as gears, joint parts, shafts, gear wheels, camshafts, bolts, pins, and cardan joints, among others. This study examined the microstructural and mechanical properties and tribological behavior of different surface treatments applied to DIN 16MnCr5 steel. The samples were hardened at 870 °C for 15 min and then quenched in water. The surface conditions evaluated were as follows: quenched and tempered DIN 16MnCr5 steel samples without surface treatments (control group), quenched and tempered DIN 16MnCr5 steel samples with gas-nitriding at 560 °C for 6 h, quenched and tempered DIN 16MnCr5 steel samples with pack boriding at 950 °C for 4 h, and quenched and tempered DIN 16MnCr5 steel samples with duplex gas-nitriding and pack boriding. Microstructure characterization was carried out using metallographic techniques, optical microscopy, scanning electron microscopy with energy-dispersive spectroscopy, and X-ray diffraction. The mechanical properties were assessed through microhardness and elastic modulus tests using nanoindentation. The tribological behavior was evaluated using pin-on-disc tests following the ASTM G99-17 standard procedure under dry sliding conditions. The results indicated that the surface treated with duplex gas-nitriding and pack boriding exhibited the highest wear resistance and a reduced coefficient of friction due to improved mechanical properties, leading to increased hardness and elastic modulus.
- Open Access
- 1 March 2024
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 8 (2) , 48
Characterization of Microstructural and Mechanical Properties of 17-4 PH Stainless Steel by Cold Rolled and Machining vs. DMLS Additive Manufacturing
The 17-4 PH stainless steel is widely used in the aerospace, petrochemical, chemical, food, and general metallurgical industries. The present study was conducted to analyze the mechanical properties of two types of 17-4 PH stainless steel—commercial cold-rolled and direct metal laser sintering (DMLS) manufactured. This study employed linear and nonlinear tensile FEM simulations, combined with various materials characterization techniques such as tensile testing and nanoindentation. Moreover, microstructural analysis was performed using metallographic techniques, optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The results on the microstructure for 17-4 PH DMLS stainless steel reveal the layers of melting due to the laser process characterized by complex directional columnar structures parallel to the DMLS build direction. The mechanical properties obtained from the simple tension test decreased by 17% for the elastic modulus, 7.8% for the yield strength, and 7% for the ultimate strength for 17-4 PH DMLS compared with rolled 17-4 PH stainless steel. The FEM simulation using the experimental tension test data revealed that the 17-4 PH DMLS stainless steel experienced a decrease in the yield strength of ~8% and in the ultimate strength of ~11%. A reduction of the yield strength of the material was obtained as the grain size increased.
- 1 March 2024
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 8 (2) , 48
Open AccessCharacterization of Microstructural and Mechanical Properties of 17-4 PH Stainless Steel by Cold Rolled and Machining vs. DMLS Additive Manufacturing
The 17-4 PH stainless steel is widely used in the aerospace, petrochemical, chemical, food, and general metallurgical industries. The present study was conducted to analyze the mechanical properties of two types of 17-4 PH stainless steel—commercial cold-rolled and direct metal laser sintering (DMLS) manufactured. This study employed linear and nonlinear tensile FEM simulations, combined with various materials characterization techniques such as tensile testing and nanoindentation. Moreover, microstructural analysis was performed using metallographic techniques, optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The results on the microstructure for 17-4 PH DMLS stainless steel reveal the layers of melting due to the laser process characterized by complex directional columnar structures parallel to the DMLS build direction. The mechanical properties obtained from the simple tension test decreased by 17% for the elastic modulus, 7.8% for the yield strength, and 7% for the ultimate strength for 17-4 PH DMLS compared with rolled 17-4 PH stainless steel. The FEM simulation using the experimental tension test data revealed that the 17-4 PH DMLS stainless steel experienced a decrease in the yield strength of ~8% and in the ultimate strength of ~11%. A reduction of the yield strength of the material was obtained as the grain size increased.
- 1 January 2018
- Published by UK Zhende Publishing Limited Company in DYNA Ingenieria e Industria
- Vol. 93 (1) , 20
DISEÑO ERGONÓMICO DE PRÓTESIS DE MIEMBRO INFERIOR PERSONALIZADAS APLICANDO INTELIGENCIA ARTIFICIAL
- 1 January 2018
- Published by UK Zhende Publishing Limited Company in DYNA Ingenieria e Industria
- Vol. 93 (1) , 20
DISEÑO ERGONÓMICO DE PRÓTESIS DE MIEMBRO INFERIOR PERSONALIZADAS APLICANDO INTELIGENCIA ARTIFICIAL
- 1 January 2018
- Published by UK Zhende Publishing Limited Company in DYNA Ingenieria e Industria
- Vol. 93 (1) , 18
SELECCIÓN DE MATERIAL BIOCOMPATIBLE DE BAJO COSTO PARA MANUFACTURA DE PRÓTESIS MAXILAR PERSONALIZADA
- 1 January 2018
- Published by UK Zhende Publishing Limited Company in DYNA Ingenieria e Industria
- Vol. 93 (1) , 18
SELECCIÓN DE MATERIAL BIOCOMPATIBLE DE BAJO COSTO PARA MANUFACTURA DE PRÓTESIS MAXILAR PERSONALIZADA
- 1 January 2017
- Published by Publicaciones DYNA in DYNA Ingenieria e Industria
- Vol. 92 (1) , 461-465
CARACTERIZACIÓN MECÁNICA DE NUEVO MATERIAL COMPUESTO ENFOCADO HACIA APLICACIONES MAXILOFACIALES
- 1 January 2017
- Published by Publicaciones DYNA in DYNA Ingenieria e Industria
- Vol. 92 (1) , 461-465
CARACTERIZACIÓN MECÁNICA DE NUEVO MATERIAL COMPUESTO ENFOCADO HACIA APLICACIONES MAXILOFACIALES
- 1 January 2017
- Published by Publicaciones DYNA in DYNA New Technologies
- Vol. 4 (1) , [8 p.]
USO DE MODELO FOTOELÁSTICO PARA LA DETECCIÓN DE ZONAS ESTRUCTURALES CRITICAS EN EL DISEÑO DE UNA PRÓTESIS MAXILOFACIAL PERSONALIZADA
- 1 January 2017
- Published by Publicaciones DYNA in DYNA New Technologies
- Vol. 4 (1) , [8 p.]
USO DE MODELO FOTOELÁSTICO PARA LA DETECCIÓN DE ZONAS ESTRUCTURALES CRITICAS EN EL DISEÑO DE UNA PRÓTESIS MAXILOFACIAL PERSONALIZADA
- 1 January 2017
- Published by UK Zhende Publishing Limited Company in DYNA New Technologies
- Vol. 4 (1) , [14 p.]
IMPLEMENTACIÓN DE LAS REDES NEURONALES ARTIFICIALES PARA SELECCIONAR LOS COMPONENTES DE UNA PRÓTESIS MODULAR TRANSFEMORAL
- 1 January 2017
- Published by UK Zhende Publishing Limited Company in DYNA New Technologies
- Vol. 4 (1) , [14 p.]
IMPLEMENTACIÓN DE LAS REDES NEURONALES ARTIFICIALES PARA SELECCIONAR LOS COMPONENTES DE UNA PRÓTESIS MODULAR TRANSFEMORAL