Jingyi Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jingyi Zhang has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Huizong Duan
MOE Key Laboratory of Tianqin Mission, Tianqin Research Center for Gravitational Physics, School of Physics and Astronomy, Frontiers Science Center for Tianqin, Gravitational Wave Research Center of CNSA, Sun Yat-sen University (Zhuhai Campus), Zhuhai, China
6 shared publications Min Ming
6 shared publications- Hsien-Chi Yeh
MOE Key Laboratory of TianQin Mission, TianQin Research Center for Gravitational Physics & School of Physics and Astronomy, Frontiers Science Center for TianQin, Gravitational Wave Research Center of CNSA, Sun Yat-sen University (Zhuhai Campus), Zhuhai 519082, People’s Republic of China
5 shared publications Bin Cao
4 shared publicationsHsien-Chi Yeh
3 shared publicationsYuanze Jiang
3 shared publications
Latest Publications
- 11 April 2025
- Published by Elsevier in Measurement
- Vol. 253
A quasi-monolithic interferometer for acceleration measurement
- 11 April 2025
- Published by Elsevier in Measurement
- Vol. 253
A quasi-monolithic interferometer for acceleration measurement
- 19 March 2025
- Published by Elsevier in Measurement
- Vol. 252
Hydroxide Catalysis Bonding settling time in different alkaline solutions
- 19 March 2025
- Published by Elsevier in Measurement
- Vol. 252
Hydroxide Catalysis Bonding settling time in different alkaline solutions
- 12 August 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (18) , 31006-31022
Ground-based simulation of laser link acquisition for inter-satellite laser interferometry
Laser link acquisition and pointing technique is one of the essential techniques for the inter-satellite laser interferometry for space-based gravitational waves detection and next-generation Earth gravity measurement missions. The first step of building up inter-satellite laser link is using an acquisition camera to capture the inter-satellite laser beam signals within a pre-scanning uncertain cone. Subsequently, high-precision angle measurement technology, namely differential wavefront sensing, is used to achieve a high pointing precision required. Due to the distance constraint of a ground-based simulation experiment, it is difficult to verify directly the feasibility of an inter-satellite laser link acquisition and pointing control scheme. By means of controlling the optical properties of the received laser beam, the long-distance beam propagation is simulated with two optical benches of an inter-satellite interferometer, and the process of a laser link acquisition experiment has been demonstrated. The experimental results show that the inter-satellite laser beams could establish the dual-way locking successfully. The fluctuation of the laser beam pointing direction (in-loop) can be suppressed to about 5 µrad in atmospheric environment. The results verify the feasibility of the laser link acquisition scheme. The experimental setup can be extended to conduct experiments with various parameters, providing technical support for further testing of the inter-satellite laser link acquisition and pointing control methods.
- 12 August 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (18) , 31006-31022
Ground-based simulation of laser link acquisition for inter-satellite laser interferometry
Laser link acquisition and pointing technique is one of the essential techniques for the inter-satellite laser interferometry for space-based gravitational waves detection and next-generation Earth gravity measurement missions. The first step of building up inter-satellite laser link is using an acquisition camera to capture the inter-satellite laser beam signals within a pre-scanning uncertain cone. Subsequently, high-precision angle measurement technology, namely differential wavefront sensing, is used to achieve a high pointing precision required. Due to the distance constraint of a ground-based simulation experiment, it is difficult to verify directly the feasibility of an inter-satellite laser link acquisition and pointing control scheme. By means of controlling the optical properties of the received laser beam, the long-distance beam propagation is simulated with two optical benches of an inter-satellite interferometer, and the process of a laser link acquisition experiment has been demonstrated. The experimental results show that the inter-satellite laser beams could establish the dual-way locking successfully. The fluctuation of the laser beam pointing direction (in-loop) can be suppressed to about 5 µrad in atmospheric environment. The results verify the feasibility of the laser link acquisition scheme. The experimental setup can be extended to conduct experiments with various parameters, providing technical support for further testing of the inter-satellite laser link acquisition and pointing control methods.
- 25 July 2024
- Published by IOP Publishing in Classical and Quantum Gravity
- Vol. 41 (16) , 165014
Long-term stability of the picometer-resolution interferometer on TianQin-1 satellite
As ground-based gravitational wave (GW) detection has opened a new window for exploring the Universe, space-based GW detection will be the next frontier to deepen the understanding of galaxy evolution and massive black holes merging. TianQin-1 is a technology verification satellite for the space-based GW detector TianQin. One of the key technologies demonstrated in TianQin-1 is a high-precision and ultra-stable interferometer, with a noise floor lower than 100 pm / Hz 1 / 2 @ 0.1 Hz . In this paper, we report the long-term stability of the interferometer in the TianQin-1 satellite, which contains a quasi-monolithic optical bench made through hydroxide catalysis bonding (HCB). According to the results of the ground and in-orbit tests, the long-term stability of the interferometer for 13 months after launch has been evaluated. The resolution of the interferometer is better than 30 pm. The noise level of the interferometer is about 30 pm / Hz 1 / 2 @ 0.1 Hz and 10 pm / Hz 1 / 2 above 1 Hz, fulfilling the mission requirement of TianQin-1. The successful in-orbit operation has demonstrated the interferometer’s high precision and long-term stability based on the quasi-monolithic optical bench.
- 25 July 2024
- Published by IOP Publishing in Classical and Quantum Gravity
- Vol. 41 (16) , 165014
Long-term stability of the picometer-resolution interferometer on TianQin-1 satellite
As ground-based gravitational wave (GW) detection has opened a new window for exploring the Universe, space-based GW detection will be the next frontier to deepen the understanding of galaxy evolution and massive black holes merging. TianQin-1 is a technology verification satellite for the space-based GW detector TianQin. One of the key technologies demonstrated in TianQin-1 is a high-precision and ultra-stable interferometer, with a noise floor lower than 100 pm / Hz 1 / 2 @ 0.1 Hz . In this paper, we report the long-term stability of the interferometer in the TianQin-1 satellite, which contains a quasi-monolithic optical bench made through hydroxide catalysis bonding (HCB). According to the results of the ground and in-orbit tests, the long-term stability of the interferometer for 13 months after launch has been evaluated. The resolution of the interferometer is better than 30 pm. The noise level of the interferometer is about 30 pm / Hz 1 / 2 @ 0.1 Hz and 10 pm / Hz 1 / 2 above 1 Hz, fulfilling the mission requirement of TianQin-1. The successful in-orbit operation has demonstrated the interferometer’s high precision and long-term stability based on the quasi-monolithic optical bench.
- Open Access
Study on TPD Phasemeter to Suppress Low-Frequency Amplitude Fluctuation and Improve Fast-Acquiring Range for GW Detection
A phasemeter as a readout system for the inter-satellite laser interferometer in a space-borne gravitational wave detector requires not only high accuracy but also insensitivity to amplitude fluctuations and a large fast-acquiring range. The traditional sinusoidal characteristic phase detector (SPD) phasemeter has the advantages of a simple structure and easy realization. However, the output of an SPD is coupled to the amplitude of the input signal and has only a limited phase-detection range due to the boundedness of the sinusoidal function. This leads to the performance deterioration of amplitude noise suppression, fast-acquiring range, and loop stability. To overcome the above shortcomings, we propose a phasemeter based on a tangent phase detector (TPD). The characteristics of the SPD and TPD phasemeters are theoretically analyzed, and a fixed-point simulation is further carried out for verification. The simulation results show that the TPD phasemeter tracks the phase information well and, at the same time, suppresses the amplitude fluctuation to the noise floor of 1 μrad/Hz1/2, which meets the requirements of GW detection. In addition, the maximum lockable step frequency of the TPD phasemeter is almost three times larger than the SPD phasemeter, indicating a greater fast-acquiring range.
Open AccessStudy on TPD Phasemeter to Suppress Low-Frequency Amplitude Fluctuation and Improve Fast-Acquiring Range for GW Detection
A phasemeter as a readout system for the inter-satellite laser interferometer in a space-borne gravitational wave detector requires not only high accuracy but also insensitivity to amplitude fluctuations and a large fast-acquiring range. The traditional sinusoidal characteristic phase detector (SPD) phasemeter has the advantages of a simple structure and easy realization. However, the output of an SPD is coupled to the amplitude of the input signal and has only a limited phase-detection range due to the boundedness of the sinusoidal function. This leads to the performance deterioration of amplitude noise suppression, fast-acquiring range, and loop stability. To overcome the above shortcomings, we propose a phasemeter based on a tangent phase detector (TPD). The characteristics of the SPD and TPD phasemeters are theoretically analyzed, and a fixed-point simulation is further carried out for verification. The simulation results show that the TPD phasemeter tracks the phase information well and, at the same time, suppresses the amplitude fluctuation to the noise floor of 1 μrad/Hz1/2, which meets the requirements of GW detection. In addition, the maximum lockable step frequency of the TPD phasemeter is almost three times larger than the SPD phasemeter, indicating a greater fast-acquiring range.
- 23 February 2023
- Published by IOP Publishing in Classical and Quantum Gravity
- Vol. 40 (6) , 065009
The analysis of the far-field phase and the tilt-to-length error contribution in space-based laser interferometry
The arm length of the space-based interferometer for gravitational wave detection is 108–109 m , and picometer precision is required. The wavefront error in the far-field coupled with the pointing jitter is a major noise source, which raises higher requirements of the wavefront quality of the telescope. By extending the analytical solutions of the far-field phase to 21 Zernike aberrations, this paper demonstrates that the far-field phase could be regarded as the sum of the effects of the individual aberrations and a phase plane with its slope related to the wavefront RMS. For individual aberrations, only low-order aberrations have a significant effect on the far-field phase, but high-order aberrations will contribute to the coupling terms which is shown as a phase slope. So there is a definite corresponding relationship between the aberrations and the far-field phase, and it can be easily illustrated graphically. Based on the analytical solutions of the far-field phase, we proposed to consider the tilt-to-length (TTL) error together with the far-field phase. The TTL error is also one of the main noise sources in space-based laser interferometry, which presents big difficulties in the optical system. We found that TTL error could be added to the far-field phase as a piston term during pointing, which then help to bring the stationary point closer to the z-axis and reduce the phase noise detected at the stationary point. By considering the TTL together with the far-field phase, the requirement of the telescope could be λ/25 wavefront RMS (λ = 1064 nm ). And there will be a large tolerance range for the TTL error, so it is only necessary to evaluate the TTL error and limit it to a suitable range, not to eliminate it.
- 23 February 2023
- Published by IOP Publishing in Classical and Quantum Gravity
- Vol. 40 (6) , 065009
The analysis of the far-field phase and the tilt-to-length error contribution in space-based laser interferometry
The arm length of the space-based interferometer for gravitational wave detection is 108–109 m , and picometer precision is required. The wavefront error in the far-field coupled with the pointing jitter is a major noise source, which raises higher requirements of the wavefront quality of the telescope. By extending the analytical solutions of the far-field phase to 21 Zernike aberrations, this paper demonstrates that the far-field phase could be regarded as the sum of the effects of the individual aberrations and a phase plane with its slope related to the wavefront RMS. For individual aberrations, only low-order aberrations have a significant effect on the far-field phase, but high-order aberrations will contribute to the coupling terms which is shown as a phase slope. So there is a definite corresponding relationship between the aberrations and the far-field phase, and it can be easily illustrated graphically. Based on the analytical solutions of the far-field phase, we proposed to consider the tilt-to-length (TTL) error together with the far-field phase. The TTL error is also one of the main noise sources in space-based laser interferometry, which presents big difficulties in the optical system. We found that TTL error could be added to the far-field phase as a piston term during pointing, which then help to bring the stationary point closer to the z-axis and reduce the phase noise detected at the stationary point. By considering the TTL together with the far-field phase, the requirement of the telescope could be λ/25 wavefront RMS (λ = 1064 nm ). And there will be a large tolerance range for the TTL error, so it is only necessary to evaluate the TTL error and limit it to a suitable range, not to eliminate it.
- 27 August 2021
- Published by IOP Publishing in Classical and Quantum Gravity
- Vol. 38 (19) , 195010
Analysis on the coupling effect of wavefront distortion and pointing misalignment in space laser interferometry
Space-based gravitational wave detection aims to measure gravitational waves with strains of down to 10 −20 in 10 −4 Hz ∼ 1 Hz frequency band. In order to achieve this measurement sensitivity, inter-satellite laser interferometry with picometer precision for an armlength of 10 8 ∼ 10 9 m is required. However, the coupling of the transmitting-beam misalignment and the wavefront distortion results in a non-negligible measurement error of intersatellite laser interferometry. Considering a wavefront distortion model composed of the first 55 terms of Zernike polynomials, we analyze the coupling effect of beam misalignment and wavefront distortion in both analytical and numerical methods. Calculation results show that the position of the stationary point is mainly determined by defocus, astigmatism and coma of the wavefront distortion of the transmitting beam. Moreover, a large defocus and small coma are preferred to achieve a better alignment of the stationary pointing direction with the inter-satellite line-of-sight, such that the coupling noise and received laser power can be optimized.
- 27 August 2021
- Published by IOP Publishing in Classical and Quantum Gravity
- Vol. 38 (19) , 195010
Analysis on the coupling effect of wavefront distortion and pointing misalignment in space laser interferometry
Space-based gravitational wave detection aims to measure gravitational waves with strains of down to 10 −20 in 10 −4 Hz ∼ 1 Hz frequency band. In order to achieve this measurement sensitivity, inter-satellite laser interferometry with picometer precision for an armlength of 10 8 ∼ 10 9 m is required. However, the coupling of the transmitting-beam misalignment and the wavefront distortion results in a non-negligible measurement error of intersatellite laser interferometry. Considering a wavefront distortion model composed of the first 55 terms of Zernike polynomials, we analyze the coupling effect of beam misalignment and wavefront distortion in both analytical and numerical methods. Calculation results show that the position of the stationary point is mainly determined by defocus, astigmatism and coma of the wavefront distortion of the transmitting beam. Moreover, a large defocus and small coma are preferred to achieve a better alignment of the stationary pointing direction with the inter-satellite line-of-sight, such that the coupling noise and received laser power can be optimized.
- 1 June 2018
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 89 (6) , 064501
Inter-satellite laser link acquisition with dual-way scanning for Space Advanced Gravity Measurements mission
Laser link acquisition is a key technology for inter-satellite laser ranging and laser communication. In this paper, we present an acquisition scheme based on the differential power sensing method with dual-way scanning, which will be used in the next-generation gravity measurement mission proposed in China, called Space Advanced Gravity Measurements (SAGM). In this scheme, the laser beams emitted from two satellites are power-modulated at different frequencies to enable the signals of the two beams to be measured distinguishably, and their corresponding pointing angles are determined by using the differential power sensing method. As the master laser beam and the slave laser beam are decoupled, the dual-way scanning method, in which the laser beams of both the master and the slave satellites scan uncertainty cones simultaneously and independently, can be used, instead of the commonly used single-way scanning method, in which the laser beam of one satellite scans and that of the other one stares. Therefore, the acquisition time is reduced significantly. Numerical simulation and experiments of the acquisition process are performed using the design parameters of the SAGM mission. The results show that the average acquisition time is less than 10 s for a scanning range of 1-mrad radius with a success rate of more than 99%.
- 1 June 2018
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 89 (6) , 064501
Inter-satellite laser link acquisition with dual-way scanning for Space Advanced Gravity Measurements mission
Laser link acquisition is a key technology for inter-satellite laser ranging and laser communication. In this paper, we present an acquisition scheme based on the differential power sensing method with dual-way scanning, which will be used in the next-generation gravity measurement mission proposed in China, called Space Advanced Gravity Measurements (SAGM). In this scheme, the laser beams emitted from two satellites are power-modulated at different frequencies to enable the signals of the two beams to be measured distinguishably, and their corresponding pointing angles are determined by using the differential power sensing method. As the master laser beam and the slave laser beam are decoupled, the dual-way scanning method, in which the laser beams of both the master and the slave satellites scan uncertainty cones simultaneously and independently, can be used, instead of the commonly used single-way scanning method, in which the laser beam of one satellite scans and that of the other one stares. Therefore, the acquisition time is reduced significantly. Numerical simulation and experiments of the acquisition process are performed using the design parameters of the SAGM mission. The results show that the average acquisition time is less than 10 s for a scanning range of 1-mrad radius with a success rate of more than 99%.
- 1 August 2010
- Published by Elsevier in Physics Letters B
- Vol. 692 (2) , 74-77
Hawking temperature and thermodynamics geometry of the 3D charged-dilaton black holes
- 1 August 2010
- Published by Elsevier in Physics Letters B
- Vol. 692 (2) , 74-77
Hawking temperature and thermodynamics geometry of the 3D charged-dilaton black holes
- 6 October 2009
- Published by IOP Publishing in Communications in Theoretical Physics
- Vol. 52 (4) , 619-621
Tunneling Radiation from a Static Spherically Symmetric Black Hole Surrounded by Quintessence
- 6 October 2009
- Published by IOP Publishing in Communications in Theoretical Physics
- Vol. 52 (4) , 619-621
Tunneling Radiation from a Static Spherically Symmetric Black Hole Surrounded by Quintessence