ZZZhenhua Zhang

Zhenhua Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhenhua Zhang has a total of 74 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Chasing a Complete Understanding of the Yanshangou Landslide in the Baihetan Reservoir Area

    by Jian-Ping Chen, An-Chi Shi, Zi-Hao Niu, Yu Xu, Zhen-Hua Zhang, Ming-Liang Chen, Lei Wang

    The Yanshangou landslide, located in the Baihetan Reservoir area, poses severe potential threats to the normal operation of the reservoir due to its distinct deformation characteristics and high sensitivity to reservoir water level fluctuations. This study systematically investigates the geological background, deformation characteristics, stability evolution, and landslide-induced surge hazards of the Yanshangou landslide in the Baihetan Reservoir area. This work only considers the influence of reservoir water level fluctuations, which is the dominant factor controlling the current progressive deformation of the landslide. Field surveys and GNSS/deep displacement monitoring results revealed that the Yanshangou landslide exhibits obvious staged deformation characteristics, and the landslide deformation rate was closely coupled with the dynamic changes in reservoir water level. A slope stability evaluation method integrating the Morgenstern–Price limit equilibrium method and Richard’s equation was established, and the results indicated that the Yanshangou landslide has low saturated permeability. Therefore, its factor of safety (FOS) presents a clear four-stage variation trend in response to reservoir water level fluctuations. A Smoothed Particle Hydrodynamics (SPH)-based numerical model was further developed to simulate the landslide-induced surges under two typical reservoir water level scenarios (815 m and 765 m). The simulation results demonstrated that a high reservoir water level led to more intense surges with greater height and higher velocity, while a low reservoir water level resulted in surges with a wider propagation range along the reservoir bank. The research findings of this study provide a comprehensive theoretical basis and detailed data support for the prevention and mitigation of geological hazards in the Baihetan Reservoir area, and also offer a reference for the hazard management of similar reservoir landslides worldwide.

  • Open Access

    An Intelligent Evaluation Method for Slope Stability Based on a Database Integrating Real Cases and Numerical Simulations

    by Junyi Jiang, Dong Li, Qingyi Yang, Zhenhua Zhang, Lei Wang, Wenru Zhao, Mingliang Chen

    Slope instability can cause severe disasters, making stability prediction essential. Machine learning has become a key tool for this purpose, as it avoids complex mechanical calculations and efficiently handles high-dimensional data. Currently, the data used in machine learning primarily originate from real-world cases. However, such cases are inherently limited in quantity and often fail to comprehensively represent all potential slope conditions. To address these limitations, this study proposes a method for constructing numerical simulation databases. Based on this, we develop a model establishment method for rapid evaluation of slope stability integrating numerical simulation with engineering cases. This study uses six characteristic parameters to assess slope stability, including unit weight γ, cohesion c, internal friction angle φ, slope angle α, slope height H, and pore pressure ratio ru. Through extensive literature mining, we established a database of 684 engineering cases. Based on statistical analysis of input parameters, a numerical simulation scheme was designed. Batch calculations were performed using MATLAB to determine simulation results. The engineering case database was then partitioned into training and testing sets for model development and validation. Subsequently, the numerical simulation database was incorporated into the training set for retesting. Results demonstrate that when considering all predictive indicators, the prediction accuracy of the GRNN-based model improved from 85% to 88.3%, while the PNN-based model showed an increase from 69% to 88.3%. This study offers new insights for optimizing numerical simulation design and enhancing machine learning performance in slope stability prediction.


  • Open Access

    Research on Automatic Recognition and Dimensional Quantification of Surface Cracks in Tunnels Based on Deep Learning

    by Zhidan Liu, Xuqing Luo, Jiaqiang Yang, Zhenhua Zhang, Fan Yang, Pengyong Miao

    Cracks serve as a critical indicator of tunnel structural degradation. Manual inspections are difficult to meet engineering requirements due to their time-consuming and labor-intensive nature, high subjectivity, and significant error rates, while traditional image processing methods exhibit poor performance under complex backgrounds and irregular crack morphologies. To address these limitations, this study developed a high-quality dataset of tunnel crack images and proposed an improved lightweight semantic segmentation network, LiteSqueezeSeg, to enable precise crack identification and quantification. The model was systematically trained and optimized using a dataset comprising 10,000 high-resolution images. Experimental results demonstrate that the proposed model achieves an overall accuracy of 95.15% in crack detection. Validation on real-world tunnel surface images indicates that the method effectively suppresses background noise interference and enables high-precision quantification of crack length, average width, and maximum width, with all relative errors maintained within 5%. Furthermore, an integrated intelligent detection system was developed based on the MATLAB (R2023b) platform, facilitating automated crack feature extraction and standardized defect grading. This system supports routine tunnel maintenance and safety assessment, substantially enhancing both inspection efficiency and evaluation accuracy. Through synergistic innovations in lightweight network architecture, accurate quantitative analysis, and standardized assessment protocols, this research establishes a comprehensive technical framework for tunnel crack detection and structural health evaluation, offering an efficient and reliable intelligent solution for tunnel condition monitoring.

  • Open Access

    A Novel Displacement Prediction Model for Inclined Anchor Bolt Based on Mindlin’s Solution

    by Zhenhua Zhang, Guojuan Xu, Banglu Xi

    Since anchoring technology is a key measure to enhance the deformation resistance of engineering structures, it is widely applied in bridges, dams, power transmission lines, and offshore platforms. The displacement of anchor bolts directly affects the deformation resistance of structures, and anchor bolts are frequently arranged at an inclination angle in engineering practice—this inclination angle significantly affects their displacement. However, existing anchor bolt displacement prediction models do not account for the influence of inclination angles. To address this gap, a novel displacement prediction model for inclined anchor bolts based on Mindlin’s solution is proposed in this paper. The validation with three experimental datasets shows that the model’s relative errors are within 5%. Even if minor measurement uncertainties regarding input parameters exist in practical engineering scenarios, the calculated displacement results will not undergo significant deviations. The anchor bolt displacement prediction model proposed in this paper may help scholars better understand the relationship between anchor bolt inclination angle and displacement.


  • Open Access

    Experimental Assessment of Scour Around Side-by-Side Double Piers in an S-Shaped Channel with Ice-Jammed Flow

    by Zhonglin Li, Zhenhua Zhang, Jueyi Sui, Jun Wang

    Through laboratory experiments in an S-shaped channel, this study analyzes how the flow Froude number, the ratio of ice-to-flow rate, pier spacing-diameter ratio, and bed material median grain size influence scour depth around side-by-side double piers under ice-jammed flow conditions. Unlike the development of a scour hole around a bridge pier in a straight channel, where the scour depth increases with the flow Froude number under ice-covered conditions, this study reveals that in an S-shaped channel, scour depth increases with the flow Froude number near the convex bank pier and decreases near the concave bank counterpart. Irrespective of ice conditions, a higher ratio of pier spacing-diameter correlates with augmented scour depth at the convex bank and diminished scour at the concave bank. As the ice-to-flow rate ratio increases, the ice jam thickness in the S-shaped channel also increases, leading to a significant decrease in the flow area and resulting in deeper scour holes around the piers. Equations have been developed to calculate the maximum scour depth around side-by-side double piers positioned in an S-shaped channel with ice-jammed flow.


  • Open Access

    A Modified Bearing Capacity Model for Inclined Shallow Anchor Cable with Experimental Verification

    by Zhenhua Zhang, Guojuan Xu, Liangjun Dai, Tao Cheng, Banglu Xi, Mingliang Chen, Jiaqiang Yang

    Most theoretical models of shallow anchor cables do not take the effect of anchor inclination into consideration, which is an important factor influencing load distribution, stress concentration, and failure mechanisms. In this paper, a modified bearing capacity was developed for a single anchor cable, taking the anchor inclination into consideration, based on the principle of limit equilibrium. Then, a series of indoor pull-out tests of single anchors with different inclinations were performed, where the effects of the anchor inclination on the bearing capacity and failure mechanisms were carefully analyzed. The experimental bearing capacities were compared to the predicted data of the proposed modified model, as well as other existing experimental results, aiming to verify the applicability and accuracy. The results show that the bearing capacity increases with decreasing anchor inclination because the vertical component of the force acting on the anchor cable increases. The failure models of the anchor cables, pulled out at different angles, exhibit an asymmetric “inverted trumpet” shape, which is caused by the varying stress distributions around the anchor cable during pull-out. In addition, the bearing capacities of the theory differ very little from the experimental and previous results, with a max error of nearly 10%. This study confirms that the proposed model reliably captures the effects of anchor inclination, providing valuable insights for designing inclined anchors in engineering practice.


  • Open Access

    Analysis of Local Scour around Double Piers in Tandem Arrangement in an S-Shaped Channel under Ice-Jammed Flow Conditions

    by Shihao Dong, Zhenhua Zhang, Zhicong Li, Pangpang Chen, Jun Wang, Guowei Li

    The stability of bridge foundations is affected by local scour, and the formation of ice jams exacerbates local scour around bridge piers. These processes, particularly the evolution of ice jams and local scour around piers, are more complex in curved sections than in straight sections. This study, based on experiments in an S-shaped channel, investigates how various factors—the flow Froude number, ice–water discharge rate, median particle diameter, pier spacing, and pier diameter—affect the maximum local scour depth around double piers in tandem and the distribution of ice jam thickness. The results indicate that under ice-jammed flow conditions, the maximum local scour depth around double piers in tandem is positively correlated with the ice–water discharge rate, pier spacing, and pier diameter and negatively correlated with median particle diameter. The maximum local scour depth is positively correlated with the flow Froude number when it ranges from 0.1 to 0.114, peaking at 0.114. Above this value, the correlation becomes negative. In curved channels, the arrangement of double piers in tandem substantially influences ice jam thickness distribution, with increases in pier diameter and spacing directly correlating with greater ice jam thickness at each cross-section. Furthermore, ice jam thickness is responsive to flow conditions, escalating with higher ice–water discharge rates and decreasing flow Froude numbers.


  • Open Access

    Local Scour around Side-by-Side Double Piers in Channel Bends under Ice-Covered Conditions—An Experimental Study

    by Feihu Song, Jun Wang, Zhenhua Zhang, Tiejie Cheng, Guowei Li, Jueyi Sui

    The pier scour process is normally intensified in the presence of an ice cover, which poses risks to the longevity and safety of bridges. In the present study, the impact of the densimetric Froude number, locations, and pier spacing of side-by-side piers on the local scour depth under ice-covered flow conditions were investigated based on clear water scour experiments in an S-shaped laboratory flume. The results demonstrated that the local scour at piers along the convex bank was more substantial than that along the concave bank when other factors stayed identical. The densimetric Froude number clearly has more impact on local scour at piers along the convex bank than that along the concave bank. Different from the mechanism of the pier scour in a straight channel, the scour depth around a pier along the convex bank in the S-shaped flume increases as the distance between two piers (or pier spacing) increases, while it decreases around the piers along the concave bank. Similar scour patterns were observed when the side-by-side piers were installed at different bend apex cross-sections. The maximum local scour depths at piers along the convex bank measured at different bend apex cross-sections were relatively unchanged when other influencing factors were held constant. However, the maximum scour depth around piers along the concave bank decreased as the bends increased toward downstream.


  • Open Access

    Experimental Investigation on the Strength and Microscopic Properties of Cement-Stabilized Aeolian Sand

    by Qiang Cui, Guang Liu, Zhenhua Zhang, Yiqiu Fang, Xudong Gu

    Aeolian sand widely exists in the desert of western China. The reinforcement of aeolian sand is of considerable significance to the construction of transmission lines in the desert. In order to study the impact of different cement contents and moisture content on the performance of the cement-stabilized aeolian sand, 18 types of samples of aeolian sand with different water and cement contents were prepared. The confined and unconfined compression tests of the aeolian sand samples were conducted on the TSZ series automatic triaxial instrument. The microscopic observation methods and macroscopic strength tests were adopted to understand the cement-stabilized mechanism. The results of the triaxial test manifest that both the moisture content and the cement content affect the stress-strain behavior of the cement-stabilized aeolian sand. The cement-stabilized effect on aeolian sand can be estimated by the degree of hydration reaction. Microscopic test results show that as the cement content increases, the pores in the microstructure decrease, and some crystalline substances appear. The content of calcium silicate hydrate (C-S-H), which is one of the hydration products, is measured by the X-ray diffraction method. The results indicate that the solidification effect of cement is related to the C-S-H percentage. For 3% water content, the percentage of C-S-H goes up first with the increase of cement content and then gradually decreases at the cement content of 6%. When the water content goes up to 5% and 7%, it is found that the production of C-S-H gel increases with cement content.