Andréa de Souza Almeida
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andréa de Souza Almeida has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Francisco Antonio Rocco Lahr
University of São Paulo
4 shared publications - André Luis Christoforo
Federal University of São Carlos, São Carlos, Brazil
3 shared publications André Luis Christoforo
Universidade Federal de Sao Carlos - UFSCar Brasil
1 shared publication- Diego Henrique de Almeida
Universidade Federal de Rondônia (UNIR)
1 shared publication - Diogo Aparecido Lopes Silva
Federal University of Sao Carlos
1 shared publication - Eduardo Chahud
Universidade Federal de Minas Gerais, Brasil
1 shared publication
Latest Publications
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30
Influence of the addition of carbon black to the mixed adhesive based on vegetable oils used to manufacture Pinus sp. composite panels
This study analyzes the influence of carbon black (CB) addition to a mixed adhesive based on vegetable oils, used in manufacturing Pinus sp. wood composite panels. To this end, test specimens were made to evaluate the following concentrations of carbon black (CB) was added at concentrations ranging from 0% to 100%. For each class of CB concentration, 6 specimens were made for physical and mechanical characterization in accordance with ABNT NBR 14810:2018 and used for microstructural analysis using Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR) of the panels. As a result, the addition of CB to the vegetable oil-based mixed adhesive resulted in statistically higher average values for the mechanical properties of the panels with 30% CB, achieving the same level of significant increase as the panels with 60% CB and 100% CB in their strength values. According to the ABNT NBR 14810:2018 standards, the panels from 0% CB to 5% CB were classified as P6 (structural panels for use in severe load conditions, in dry conditions) and the panels from 10% CB to 100% CB were classified as P7 (structural panels for use in severe load conditions, in humid environments).
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30
Open AccessInfluence of the addition of carbon black to the mixed adhesive based on vegetable oils used to manufacture Pinus sp. composite panels
This study analyzes the influence of carbon black (CB) addition to a mixed adhesive based on vegetable oils, used in manufacturing Pinus sp. wood composite panels. To this end, test specimens were made to evaluate the following concentrations of carbon black (CB) was added at concentrations ranging from 0% to 100%. For each class of CB concentration, 6 specimens were made for physical and mechanical characterization in accordance with ABNT NBR 14810:2018 and used for microstructural analysis using Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR) of the panels. As a result, the addition of CB to the vegetable oil-based mixed adhesive resulted in statistically higher average values for the mechanical properties of the panels with 30% CB, achieving the same level of significant increase as the panels with 60% CB and 100% CB in their strength values. According to the ABNT NBR 14810:2018 standards, the panels from 0% CB to 5% CB were classified as P6 (structural panels for use in severe load conditions, in dry conditions) and the panels from 10% CB to 100% CB were classified as P7 (structural panels for use in severe load conditions, in humid environments).
- Open Access
- 10 July 2023
- Published by Instituto Federal de Educacao, Ciencia e Tecnologia da Paraiba in Revista Principia
- Vol. 60 (3) , 1037
Estruturas mistas madeira-concreto: o emprego da metodologia do Eurocode 5 no âmbito nacional
Estruturas mistas de madeira-concreto unem as melhores qualidades da madeira e do concreto, resultando em estruturas mais leves, rígidas e resistentes. São utilizadas na restauração de pisos e pontes de madeira, bem como na construção destas, em que se percebe um aumento da utilização desse sistema estrutural. Todavia, ainda são poucas as informações referentes às estruturas mistas em madeira-concreto na literatura, e o seu dimensionamento é abordado apenas pela normativa europeia Eurocode 5 (CEN, 2004). Nesse contexto, este trabalho apresenta as principais considerações a respeito do dimensionamento desse sistema estrutural e as principais divergências no emprego de tal técnica, essencialmente no Brasil, considerando a normativa brasileira em estruturas em madeira, para um eventual acréscimo sobre estruturas em madeira-concreto na ABNT NBR 7190 (ABNT, 1997). Ao final, é possível concluir que alguns ensaios padrões precisam ser normalizados para a implementação do dimensionamento dessa estrutura mista na norma brasileira, como por exemplo o ensaio do módulo de deslizamento do conector.
- 10 July 2023
- Published by Instituto Federal de Educacao, Ciencia e Tecnologia da Paraiba in Revista Principia
- Vol. 60 (3) , 1037
Open AccessEstruturas mistas madeira-concreto: o emprego da metodologia do Eurocode 5 no âmbito nacional
Estruturas mistas de madeira-concreto unem as melhores qualidades da madeira e do concreto, resultando em estruturas mais leves, rígidas e resistentes. São utilizadas na restauração de pisos e pontes de madeira, bem como na construção destas, em que se percebe um aumento da utilização desse sistema estrutural. Todavia, ainda são poucas as informações referentes às estruturas mistas em madeira-concreto na literatura, e o seu dimensionamento é abordado apenas pela normativa europeia Eurocode 5 (CEN, 2004). Nesse contexto, este trabalho apresenta as principais considerações a respeito do dimensionamento desse sistema estrutural e as principais divergências no emprego de tal técnica, essencialmente no Brasil, considerando a normativa brasileira em estruturas em madeira, para um eventual acréscimo sobre estruturas em madeira-concreto na ABNT NBR 7190 (ABNT, 1997). Ao final, é possível concluir que alguns ensaios padrões precisam ser normalizados para a implementação do dimensionamento dessa estrutura mista na norma brasileira, como por exemplo o ensaio do módulo de deslizamento do conector.
- Open Access
- 1 April 2023
- Published by FapUNIFESP (SciELO) in Ambiente Construído
- Vol. 23 (2) , 213-224
Estimativa das propriedades de flexão estática, dureza e tenacidade de madeiras tropicais brasileiras através de análise de porosimetria por intrusão de mercúrio
Resumo ANBR 7190 (ABNT, 1997) define a caracterização simplificada, onde há o uso de relações matemáticas entre as propriedades de resistência e rigidez. Devido à grande influência da porosidade e da densidade aparente nas propriedades das madeiras e à busca por modelos matemáticos cada vez mais precisos, este trabalho teve como objetivo’ gerar modelos de regressão para a estimativa das propriedades de flexão estática (resistência “f M ” e módulo “E M ”), resistência à dureza paralela “f H,0 ” e normal às fibras “f H,90 ”, e resistência à tenacidade “W” de madeiras tropicais brasileiras a partir dos valores de porosidade, obtidos por meio da análise de porosimetria por intrusão de mercúrio, da densidade aparente e com base em ambas as propriedades em modelos de regressão multivariáveis. Todos os modelos de regressão apresentaram coeficientes de determinação “R2” superiores a 50%. A f M , a f H,90 e a W foram melhor estimadas pela densidade aparente, enquanto o E M e a f H,0 foram melhor estimados considerando a densidade aparente e a porosidade.
- 1 April 2023
- Published by FapUNIFESP (SciELO) in Ambiente Construído
- Vol. 23 (2) , 213-224
Open AccessEstimativa das propriedades de flexão estática, dureza e tenacidade de madeiras tropicais brasileiras através de análise de porosimetria por intrusão de mercúrio
Resumo ANBR 7190 (ABNT, 1997) define a caracterização simplificada, onde há o uso de relações matemáticas entre as propriedades de resistência e rigidez. Devido à grande influência da porosidade e da densidade aparente nas propriedades das madeiras e à busca por modelos matemáticos cada vez mais precisos, este trabalho teve como objetivo’ gerar modelos de regressão para a estimativa das propriedades de flexão estática (resistência “f M ” e módulo “E M ”), resistência à dureza paralela “f H,0 ” e normal às fibras “f H,90 ”, e resistência à tenacidade “W” de madeiras tropicais brasileiras a partir dos valores de porosidade, obtidos por meio da análise de porosimetria por intrusão de mercúrio, da densidade aparente e com base em ambas as propriedades em modelos de regressão multivariáveis. Todos os modelos de regressão apresentaram coeficientes de determinação “R2” superiores a 50%. A f M , a f H,90 e a W foram melhor estimadas pela densidade aparente, enquanto o E M e a f H,0 foram melhor estimados considerando a densidade aparente e a porosidade.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 22 (6)
Influence of treatment with water-soluble CCB preservative on the physical-mechanical properties of brazilian tropical timber
This aim of this work is to present an analysis of the influence of impregnation against biological demand, realized with saline solution of CCB (Chromated Copper Borate preservative) by vacuum-pressure process, on physical-mechanical properties of tropical wood species Simarouba sp., Cedrelinga catenaeformis and Erisma uncinatum Warm. In theory, such process could increase the number of surface defects in wood pieces and reduce its strength properties. To investigate this influence, the complete species characterization was carried out in two conditions (without treatment and CCB treated wood). Tukey’s multiple comparisons test (5% significance level) was applied. In addition, scanning electron microscopy (SEM) photomicrographs were obtained with the energy dispersive spectroscopy (EDS) to investigate preservative presence at the cellular level. Results permitted to conclude that CCB impregnation process did not affect physical-mechanical properties of the studied species.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 22 (6)
Open AccessInfluence of treatment with water-soluble CCB preservative on the physical-mechanical properties of brazilian tropical timber
This aim of this work is to present an analysis of the influence of impregnation against biological demand, realized with saline solution of CCB (Chromated Copper Borate preservative) by vacuum-pressure process, on physical-mechanical properties of tropical wood species Simarouba sp., Cedrelinga catenaeformis and Erisma uncinatum Warm. In theory, such process could increase the number of surface defects in wood pieces and reduce its strength properties. To investigate this influence, the complete species characterization was carried out in two conditions (without treatment and CCB treated wood). Tukey’s multiple comparisons test (5% significance level) was applied. In addition, scanning electron microscopy (SEM) photomicrographs were obtained with the energy dispersive spectroscopy (EDS) to investigate preservative presence at the cellular level. Results permitted to conclude that CCB impregnation process did not affect physical-mechanical properties of the studied species.
- Open Access
- 1 January 2018
- Published by Scientific and Academic Publishing in International Journal of Materials Engineering
- Vol. 8 (1) , 5-11
Stress Distribution in Tauari Wood Beam
Wood is widely used in many sectors of civil construction as a structural material. Brazilian code ABNT NBR 7190:1997 Design of Timber Structures governs the method of project design as well as the characterization of wood for structural design. In this aspect the code considers wood as an orthoptic material, however is well known that the organic origin provides great anatomical complexity to its. This work aims to study the distribution of normal stresses in a Tauari wood beam subjected to the elastic regime, and to ascertain the current position of the Neutral Line during test. For this purpose, a four-point static bending test and subsequent compression and tension to the grain tests were performed to determine the modulus of elasticity and calculate the normal stresses by recording deformations and applying Hooke's Law. The data were statistically analyzed to define bests adjusts to Stress vs. Strain diagrams, and thus determine the location of the Neutral Line. It was verified that the position of the Neutral Line was a normal distribution variable, being located at 1,07cm above the geometric center of the board. Finally, the comparison between values of normal tension obtained experimentally and through the theoretical method was determined and similarities were verified in these data, being also plausible the theory for the calculation of the normal tensions of the wood beams, when it is in the elastic regime.
- 1 January 2018
- Published by Scientific and Academic Publishing in International Journal of Materials Engineering
- Vol. 8 (1) , 5-11
Open AccessStress Distribution in Tauari Wood Beam
Wood is widely used in many sectors of civil construction as a structural material. Brazilian code ABNT NBR 7190:1997 Design of Timber Structures governs the method of project design as well as the characterization of wood for structural design. In this aspect the code considers wood as an orthoptic material, however is well known that the organic origin provides great anatomical complexity to its. This work aims to study the distribution of normal stresses in a Tauari wood beam subjected to the elastic regime, and to ascertain the current position of the Neutral Line during test. For this purpose, a four-point static bending test and subsequent compression and tension to the grain tests were performed to determine the modulus of elasticity and calculate the normal stresses by recording deformations and applying Hooke's Law. The data were statistically analyzed to define bests adjusts to Stress vs. Strain diagrams, and thus determine the location of the Neutral Line. It was verified that the position of the Neutral Line was a normal distribution variable, being located at 1,07cm above the geometric center of the board. Finally, the comparison between values of normal tension obtained experimentally and through the theoretical method was determined and similarities were verified in these data, being also plausible the theory for the calculation of the normal tensions of the wood beams, when it is in the elastic regime.