KOKrzysztof Olasek

Krzysztof Olasek

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Krzysztof Olasek has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Velocity data-based determination of airfoil characteristics with circulation and fluid momentum change methods, including a control surface size independence test

    by Krzysztof Olasek, Maciej Karczewski

    An experimental method for determination of aerodynamic loads is presented. It is based on velocity vector field results obtained with Particle Image Velocimetry (PIV). As PIV is an optical measurement technique, the developed method for load determination can be defined as noninvasive. It is shown that the only information needed to estimate the lift and drag forces exerted on a body placed in the flow is a velocity distribution measured around the investigated object. Therefore, PIV results provide sufficient input experimental data to be used. Fundamental fluid mechanics theories were employed to develop algorithms for load estimation. Determination of the lift force is based on velocity circulation calculations. It is obtained by integrating the velocity field along a closed-loop encircling the body. An essential achievement made is the development of a procedure for finding an optimal size of the integration curve used for lift calculations. In the case of the drag force estimation, an analysis of fluid momentum changes has been used. The momentum deficit, within a given control volume containing the analysed aerofoil, is determined and related to the reaction drag force exerted on the body. Additionally, pressure field reconstruction based on velocity data, which enabled an application of small control surfaces and kept the drag estimation error at a satisfactorily low level, was introduced. The developed method was tested and verified with the reference computational fluid dynamics simulation results and applied further to the wind tunnel experimental data. A flow around the standard NACA0012 aerofoil at two flow regimes was investigated (Re= $$0.7\times 10^5$$ 0.7 × 10 5 and Re= $$1.4\times 10^5$$ 1.4 × 10 5 ). Lift and drag coefficient characteristics as a function of the angle of attack were obtained. An exceptional agreement between the experimental and reference numerical lift characteristics was attained (relative differences no larger than 5%). In the case of drag estimation, an acceptable level of similarity was observed (max. discrepancies below 20%). Graphic


  • Experimental Study of Vaneless Diffuser Rotating Stall Development and Cell-Merging Phenomena

    by Filip Grapow, Krzysztof Olasek, Grzegorz Liśkiewicz, Radomir Magiera, Władysław Kryłłowicz

    This paper describes the vaneless diffuser rotating stall (VDRS) development and cell-merging phenomena. A centrifugal compressor’s lifespan may be limited by flow instabilities occurring in off-design operation. One such instability is the VDRS, which generates oscillating, asymmetrical flow fields in the diffuser and, thus, undesired forces acting on the rotor. Understanding and prevention of VDRS behavior are crucial for achieving safe and undisturbed compressor operation. Experimental measurements of centrifugal compressors operating under the influence of VDRS have been presented. Two different approaches were used for the identification of VDRS: pressure measurements and two-dimensional (2D) particle image velocimetry (PIV). Frequency analysis based on spectral maps and cell development processes were investigated. The presented results showed that mass flowrate has an impact on the rotating frequency of both the entire structure and single cells. Additionally, it affects radial cell size, which grows with compressor throttling and ultimately reaches the length of the diffuser. During the experiments, the cell-merging phenomenon was observed which has not been widely described in the literature. The results presented in this paper allow a better understanding of vaneless diffuser rotating stall behavior. The phenomenon of the change of cell size and frequency could be very important for machine fatigue. Cell-merging could also have an impact on the machine’s vibrations and flow stability. Since it is believed that VDRS is one of the factors inducing surge, its understanding and prevention may have a positive influence on surge margins.


  • Numerical and experimental analysis of rotating wheel in contact with the ground

    by Michal Kulak, Maciej Karczewski, Pawel Lesniewicz, Krzysztof Olasek, Bas Hoogterp, Guillaume Spolaore, Krzysztof Józwik

    Purpose: This paper aims to provide the results of investigations concerning an influence of the tyre with longitudinal grooves on the car body aerodynamics. It is considered as an important aspect affecting the vehicle aerodynamic drag. Design/methodology/approach: To investigate a contribution of grooved tyres to the overall vehicle drag, three wind tunnel experimental campaigns were performed (two by Peugeot Société Anonyme Peugeot Citroen, one at the Lodz University of Technology). In parallel, computational fluid dynamics (CFD) simulations were conducted with the ANSYS CFX software to enable formulation of wider conclusions. Findings: The research shows that optimised tread patterns can be derived on a single tyre via a CFD study in combination with a controlled experiment to deliver designs actively lowering the overall vehicle aerodynamic drag. Practical implications: A reduction in the aerodynamic drag is one of ways to decrease vehicle fuel consumption. Alternatively, it can be translated into an increase in the maximum travel velocity and the maximum distance driven (key factor in electric vehicles), as well as in a reduction of CO2 emissions. Finally, it can improve the vehicle driving and steering stability. Originality/value: The tyre tread pattern analysis on isolated wheels provides an opportunity to cut costs of R&D and could be a step towards isolating aerodynamic properties of tyres, irrespective of the car body on which they are applied.


  • CFD analysis of Diffuser Augmented Wind Turbine model for wind tunnel investigation

    by Michal Kulak, Maciej Karczewski, Krzysztof Olasek, Krzysztof Jozwik

    The paper discusses results of integration of experimental campaign with CFD studies, where a small wind turbine placed inside a wind tunnel test section has been examined. Investigation included determination of model size influence on flow blockage effects. The CFD model helps to reduce time spent at the experimental stand and, therefore, costs pointing to the model with acceptable dimensions. CFD has been also used to anticipate the loads that may be exerted on the model thus helping to understand necessary measures in the upcoming aeromechanics study of the construction. The study concerns a wind turbine placed inside a diffuser channel, a solution known as Diffuser Augmented Wind Turbine (DAWT). This type of wind energy converter has recently been an object of numerous studies at the Institute of Turbomachinery of Lodz University of Technology. The examined model sizes included: D_5, D_10, D_20, D_30, D_80 and D_real, where the number states the per cent of test object's cross section area related to the cross-section area of the wind tunnel outlet nozzle supplying air to the test location. The numerical study has been based on a commercial solver ANSYS CFX 15.0, the comparison of the obtained results with available experimental data for D_5, D_30 and D_80 models has been made, leading to the analysis of the results obtained and the conclusions.


  • Wind tunnel experimental investigations of a diffuser augmented wind turbine model

    by Krzysztof Olasek, Maciej Karczewski, Michal Lipian, Piotr Wiklak, Krzysztof Józwik

    Purpose: A solution to increase the energy production rate of the wind turbine is proposed by forcing more air to move through the turbine working section. This can be achieved by equipping the rotor with a diffusing channel ended with a brim (diffuser augmented wind turbine – DAWT). The purpose of this paper is to design an experimental stand and perform the measurements of velocity vector fields through the diffuser and power characteristic of the wind turbine. Design/methodology/approach: The experiments were carried out in a small subsonic wind tunnel at the Institute of Turbomachinery, Lodz University of Technology. An experimental stand design process as well as measurement results are presented. Model size sensitivity study was performed at the beginning. The experimental campaign consisted of velocity measurements by means of particle image velocimetry (PIV) and pneumatic pitot probe as well as torque and rotational velocity measurements. Findings: Characteristics (power coefficient vs tip speed ratio) of the bare and shrouded wind turbine were obtained. The results show an increase in the wind turbine power up to 70-75 per cent by shrouding the rotor with a diffuser. The mechanisms responsible for such a power increase were well explained by the PIV and pneumatic measurement results revealing the nature of the flow through the diffuser. Research limitations/implications: Experimental stand for wind turbine rotor testing is of a preliminary character. Most optimal methodology for obtaining power characteristic should be determined now. Presented results can serve as good input for choice of stable and reliable control system of wind turbine operational parameters. Practical implications: A 3 kW DAWT is being developed at the Institute of Turbomachinery, Lodz University of Technology. Aim of the study is to design a compact and smart wind turbine optimised for low wind speed conditions. Developed wind turbine has a potential to be used as an effective element within a net of distributed generation, e.g. for domestic use. Originality/value: Research carried out is the continuation of theoretical study began in 1970s. It was also inspired by practical solutions proposed by Japanese researchers few years ago. Presented paper is the summary of work devoted to optimisation of the DAWT for wind conditions in the region. Original solution has been applied, e.g. for experimental stand design (3D printing application).


  • Open Access

    Sensitivity study of diffuser angle and brim height parameters for the design of 3 kW Diffuser Augmented Wind Turbine

    by Michał Lipian, Maciej Karczewski, Krzysztof Olasek

    The Diffuser Augmented Wind Turbine (DAWT) is an innovative mean to increase the power harvested by wind turbine. By encompassing the rotor with a diffusershaped duct it is possible to increase the flow speed through the turbine by about 40-50%. The study presents the development of a numerical model and its validation by the experiments performed in the wind tunnel of the Institute of Turbomachinery, TUL. Then, the numerical model is used for the geometry sensitivity study to optimize the shape of a diffuser. The paper presents that the DAWT technology has the potential to even double the power outcome of wind turbine when compared to a bare rotor version.