JMJoseph McDonald

Joseph McDonald

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Joseph McDonald has a total of 94 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Particle emissions from mobile sources: Discussion of ultrafine particle emissions and definition

    by David Kittelson, Imad Khalek, Joseph McDonald, Jeffrey Stevens, Robert Giannelli


  • Benchmarking a 2018 Toyota Camry 2.5-Liter Atkinson Cycle Engine with Cooled-EGR

    by John Kargul, Mark Stuhldreher, Daniel Barba, Charles Schenk, Stanislav Bohac, Joseph McDonald, Paul Dekraker

    As part of the U.S. Environmental Protection Agency’s (EPA’s) continuing assessment of advanced light-duty automotive technologies in support of regulatory and compliance programs, a 2018 Toyota Camry A25A-FKS 4-cylinder, 2.5-liter, naturally aspirated, Atkinson Cycle engine with cooled exhaust gas recirculation (cEGR) was benchmarked. The engine was tested on an engine dynamometer with and without its 8-speed automatic transmission, and with the engine wiring harness tethered to a complete vehicle parked outside of the test cell. Engine and transmission torque, fuel flow, key engine temperatures and pressures, onboard diagnostics (OBD) data, and Controller Area Network (CAN) bus data were recorded. This paper documents the test results under idle, low, medium, and high load engine operation. Motoring torque, wide open throttle (WOT) torque and fuel consumption are measured during transient operation using both EPA Tier 2 and Tier 3 test fuels. The design and performance of this 2018 2.5-liter engine is described and compared to Toyota’s published data and to EPA’s previous projections of the efficiency of an Atkinson Cycle engine with cEGR. The Brake Thermal Efficiency (BTE) map for the Toyota A25A-FKS engine shows a peak efficiency near 40 percent, which is the highest value of any publicly available map for a non-hybrid production gasoline internal combustion (IC) engine designed to run on 91 RON fuel. Further improvement is possible by application of fixed discrete or full continuous cylinder deactivation, both of which are currently in production on other engines.


  • Real-World Emission Modeling and Validations Using PEMS and GPS Vehicle Data

    by SoDuk Lee, Carl Fulper, Joseph McDonald, Michael Olechiw

    Portable Emission Measurement Systems (PEMS) are used by the U.S. Environmental Protection Agency (EPA) to measure gaseous and particulate mass emissions from vehicles in normal, in-use, on-the-road operation to support many of its programs, including assessing mobile source emissions compliance, emissions factor assessment for in-use fleet modeling, and collection of in-use vehicle operational data to support vehicle simulation modeling programs. This paper discusses EPA’s use of Global Positioning System (GPS) measured altitude data and electronically logged vehicle speed data to provide real-world road grade data for use as an input into the Gamma Technologies GT-DRIVE+ vehicle model. The GPS measured altitudes and the CAN vehicle speed data were filtered and smoothed to calculate the road grades by using open-source Python code and associated packages. Ambient temperature, ambient pressure, humidity, wind direction, and speeds were used to simulate actual driving environment conditions, and to calculate vehicle performance, fuel economy, and emissions associated with environmental effects. Complete engine maps, transmission efficiencies, and vehicle data were used as inputs into the GT-DRIVE+ vehicle model to estimate fuel economy, greenhouse gas (GHG) and NOx emissions of a vehicle equipped with a 12-volt start-stop system. The model-simulated fuel economy, GHG and NOx emissions, engine torque, engine speed, and vehicle speeds were all in good agreement with the on-road measured fuel economy, GHG and NOx emissions from the PEMS vehicle test data.


  • Predictive GT-Power Simulation for VNT Matching to EIVC Strategy on a 1.6 L Turbocharged GDI Engine

    by Yanyu Wang, Graham Conway, Joseph McDonald, Aaron Birckett

    The use of early intake valve closing (EIVC) can lead to improvements in spark-ignition engine efficiency. One of the greatest barriers facing adoption of EIVC for high power-density applications is the challenge of boosting as EIVC strategies reduce volumetric efficiency. Turbochargers with variable nozzle turbines (VNT) have recently been developed for gasoline applications operating at high exhaust gas temperatures. The use of a single VNT as a boost device may provide a lower-cost option compared to two-stage boosting systems or 48 V electronic boost devices for some EIVC applications. A predictive model was created based on engine testing results from a 1.6 L turbocharged gasoline direct injection engine [1]. The model was tuned so that it predicted burn-rates and end-gas knock over an engine operating map with varying speeds, loads, compression ratios and fuel types. Using the model, an assessment of VNT performance was implemented using compressor and turbine maps made available from Garrett Motion, Inc. Results show that the single VNT device supports mild EIVC across the operating map while maintaining acceptable full-load performance and maintaining or improving upon thermal efficiency compared to a twin-scroll turbocharger. This work was done as part of the Environmental Protection Agency’s regulatory assessment of advanced light-duty automotive technologies.


  • Open Access

    Predicting the Future Manufacturing Cost of Batteries for Plug-In Vehicles for the U.S. Environmental Protection Agency (EPA) 2017–2025 Light-Duty Greenhouse Gas Standards

    by Michael J. Safoutin, Joseph McDonald, Ben Ellies

    In developing the U.S. 2017–2025 Light-Duty Vehicle Greenhouse Gas Emissions Standards, the U.S. Environmental Protection Agency (EPA) modeled lithium-ion battery packs for future electrified vehicles to estimate their direct manufacturing costs through 2025. As part of the 2016 Midterm Evaluation of the standards for model years (MY) 2022 to 2025, the analysis was revised to account for developments in battery design since the 2012 rulemaking. This paper describes the methodology that was used for estimating battery capacity, power, and cost, and compares the projected cost estimates to other sources. An empirical equation is derived for specifying motor power as a function of target acceleration time, and suggested factors for converting cell-level costs to pack-level costs are developed.


  • Predictive GT-Power Simulation for VNT Matching on a 1.6 L Turbocharged GDI Engine

    by Dennis Robertson, Graham Conway, Chris Chadwell, Joseph McDonald, Daniel Barba, Mark Stuhldreher, Aaron Birckett

    The thermal efficiency benefits of low-pressure (LP) exhaust gas recirculation (EGR) in spark-ignition engine combustion are well known. One of the greatest barriers facing adoption of LP-EGR for high power-density applications is the challenge of boosting. Variable nozzle turbines (VNTs) have recently been developed for gasoline applications operating at high exhaust gas temperatures (EGTs). The use of a single VNT as a boost device may provide a lower-cost option compared to two-stage boosting systems or 48 V electronic boost devices for some LP-EGR applications. A predictive model was created based on engine testing results from a 1.6 L turbocharged gasoline direct injection (GDI) engine [1]. The model was tuned so that it predicted burn-rates and end-gas knock over an engine operating map with varying speeds, loads, EGR rates and fuel types. Using the model, an assessment of VNT performance was performed using compressor and turbine maps made available from Honeywell Transportation Systems. Results show that the single VNT device supports LP-EGR across the operating map while maintaining realistic full-load performance and maintaining or improving upon thermal efficiency compared to a twin-scroll turbocharger. This work was done as part of the Environmental Protection Agency’s continuing assessment of advanced light-duty automotive technologies to support setting appropriate national greenhouse gas standards.


  • Modeling and Controls Development of 48 V Mild Hybrid Electric Vehicles

    by SoDuk Lee, Jeff Cherry, Michael Safoutin, Anthony Neam, Joseph McDonald, Kevin Newman

    The Advanced Light-Duty Powertrain and Hybrid Analysis tool (ALPHA) was created by EPA to evaluate the Greenhouse Gas (GHG) emissions of Light-Duty (LD) vehicles. ALPHA is a physics-based, forward-looking, full vehicle computer simulator capable of analyzing various vehicle types combined with different powertrain technologies. The ALPHA desktop application was developed using MATLAB/Simulink. The ALPHA tool was used to evaluate technology effectiveness and off-cycle technologies such as air-conditioning, electrical load reduction technology and road load reduction technologies of conventional, non-hybrid vehicles for the Midterm Evaluation of the 2017-2025 LD GHG rule by the U.S. Environmental Protection Agency (EPA) Office of Transportation and Air Quality (OTAQ). This paper presents controls development, modeling results, and model validation for simulations of a vehicle with a 48 V Belt Integrated Starter Generator (BISG) mild hybrid electric vehicle and an initial model design for a 48 V inline on-axis P2-configuration mild hybrid electric vehicle. Both configurations were modeled with a MATLAB/Simulink/Stateflow tool, which has been integrated into EPA’s ALPHA vehicle model and was also used to model components within Gamma Technology GT-DRIVE simulations. The mild hybrid electric vehicle model was validated using vehicle data obtained from Argonne National Laboratory (ANL) chassis dynamometer tests of a 2013 Chevrolet Malibu Eco 115 V 15 kW BISG mild hybrid electric vehicle. The simulated fuel economy, engine torque/speed, motor torque/speed, engine on-off controls, battery voltage, current, and State of Charge (SOC) were all in good agreement with the vehicle test data on a number of drive schedules. The developed 48 V mild hybrid electric vehicle model can be used to estimate the GHG emissions and fuel economy of 48 V mild hybrid electric vehicles over the EPA regulatory drive cycles and to estimate off-cycle GHG emissions. The 48 V mild hybrid electric vehicle model will be further validated with additional 48 V mild hybrid electric vehicle test data in the future as more vehicle models become available. EPA has included 48 V BISG mild hybrid electric vehicle technology in its assessment of CO2-reducing technologies available for compliance with U.S. GHG standards.


  • Modeling and Validation of 48V Mild Hybrid Lithium-Ion Battery Pack

    by SoDuk Lee, Jeff Cherry, Michael Safoutin, Joseph McDonald, Michael Olechiw

    As part of the midterm evaluation of the 2022-2025 Light-Duty Vehicle Greenhouse Gas (GHG) Standards, the U.S. Environmental Protection Agency (EPA) developed simulation models for studying the effectiveness of 48V mild hybrid electric vehicle (MHEV) technology for reducing CO2 emissions from light-duty vehicles. Simulation and modeling of this technology requires a suitable model of the battery. This article presents the development and validation of a 48V lithium-ion battery model that will be integrated into EPA’s Advanced Light-Duty Powertrain and Hybrid Analysis (ALPHA) vehicle simulation model and that can also be used within Gamma Technologies, LLC (Westmont, IL) GT-DRIVE™ vehicle simulations. The battery model is a standard equivalent circuit model with the two-time constant resistance-capacitance (RC) blocks. Resistances and capacitances were calculated using test data from an 8 Ah, 0.4 kWh, 48V (nominal) lithium-ion battery obtained from a Tier 1 automotive supplier, A123 Systems, and developed specifically for 48V mild hybrid vehicle applications. The A123 Systems battery has 14 pouch-type lithium-ion cells arranged in a 14 series and 1 parallel (14S1P) configuration. The RC battery model was validated using battery test data generated by a hardware-in-the-loop (HIL) system that simulated the impact of MHEV operation on the A123 systems 48V battery pack over U.S. regulatory drive cycles. The HIL system matched charge and discharge data originally generated by Argonne National Laboratory (ANL) during chassis dynamometer testing of a 2013 GM Chevrolet Malibu Eco 115V MHEV. All validation testing was performed at the battery test facility (BTF) at the U.S. EPA National Vehicle and Fuel Emissions Laboratory (NVFEL) in Ann Arbor, Michigan. The simulated battery voltages, currents, and state of charge (SOC) of the HIL tests were in good agreement with vehicle test data over a number of different drive cycles, and excellent agreement was achieved between RC model simulations of the 48V battery and HIL battery test data.


  • Benchmarking a 2016 Honda Civic 1.5-Liter L15B7 Turbocharged Engine and Evaluating the Future Efficiency Potential of Turbocharged Engines

    by Mark Stuhldreher, John Kargul, Daniel Barba, Joseph McDonald, Stanislav Bohac, Paul Dekraker, Andrew Moskalik

    As part of the U.S. Environmental Protection Agency’s (EPA’s) continuing assessment of advanced light-duty (LD) automotive technologies to support the setting of appropriate national greenhouse gas (GHG) standards and to evaluate the impact of new technologies on in-use emissions, a 2016 Honda Civic with a 4-cylinder 1.5-liter L15B7 turbocharged engine and continuously variable transmission (CVT) was benchmarked. The test method involved installing the engine and its CVT in an engine-dynamometer test cell with the engine wiring harness tethered to its vehicle parked outside the test cell. Engine and transmission torque, fuel flow, key engine temperatures and pressures, and onboard diagnostics (OBD)/Controller Area Network (CAN) bus data were recorded. This article documents the test results for idle, low, medium, and high load engine operation, as well as motoring torque, wide-open throttle (WOT) torque, and fuel consumption during transient operation using both EPA Tier 2 and Tier 3 test fuels. Particular attention is given to characterizing enrichment control during high load engine operation. Results are used to create complete engine fuel consumption and efficiency maps and estimate CO2 emissions using EPA’s Advanced Light-Duty Powertrain and Hybrid Analysis (ALPHA) full vehicle simulation model, over regulatory drive cycles. The design and performance of the 1.5-liter Honda engine are compared to several other past, present, and future downsized-boosted engines, and potential advancements are evaluated.


  • Evaluation of Emerging Technologies on a 1.6 L Turbocharged GDI Engine

    by Graham Conway, Dennis Robertson, Chris Chadwell, Joseph McDonald, John Kargul, Daniel Barba, Mark Stuhldreher

    Low-pressure loop exhaust gas recirculation (LP- EGR) combined with higher compression ratio, is a technology package that has been a focus of research to increase engine thermal efficiency of downsized, turbocharged gasoline direct injection (GDI) engines. Research shows that the addition of LP-EGR reduces the propensity to knock that is experienced at higher compression ratios [1]. To investigate the interaction and compatibility between increased compression ratio and LP-EGR, a 1.6 L Turbocharged GDI engine was modified to run with LP-EGR at a higher compression ratio (12:1 versus 10.5:1) via a piston change. This paper presents the results of the baseline testing on an engine run with a prototype controller and initially tuned to mimic an original equipment manufacturer (OEM) baseline control strategy running on premium fuel (92.8 anti-knock index). This paper then presents test results after first adding LP-EGR to the baseline engine, and then also increasing the compression ratio (CR) using 12:1 pistons. As a last step, the 10.5 CR engine with LP-EGR was run on regular fuel (87.7 anti-knock index) to verify that this configuration could be calibrated to maintain performance like the baseline engine running on premium fuel. To understand the effect of each technology and operating strategy combination on vehicle fuel economy, the various engine maps were compared in EPA’s Advanced Light-Duty Powertrain and Hybrid Analysis (ALPHA) tool over U.S. regulatory drive cycles. This work was done in close collaboration with U.S. EPA engineers as part of their continuing assessment of advanced light-duty automotive technologies to support setting appropriate national greenhouse gas standards.