WLWon-Jae Lee

Won-Jae Lee

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Won-Jae Lee has a total of 215 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Identifying (001) and (1¯01) Reflection Twin Domains in EFG‐Grown β ‐Ga 2 O 3

    by So Min Shin, Yun Jin Kim, Dae Uk Kim, Eun Seo Lee, Eun Jeong An, Mi Seon Park, Gwang Hee Jung, Yun Ji Shin, Seong Min Jeong, Jung Gon Kim, et al.

    The edge‐defined film‐fed growth (EFG) method is advantageous for large‐area substrate fabrication owing to its melt‐based bulk growth process. However, twin defects frequently generated during growth act as a major factor degrading device performance. The (01) plane, known as the twin plane of the (001) surface, exhibits an identical atomic arrangement to the (001) plane when projected along the c ‐axis, making them difficult to distinguish using transmission electron microscopy (TEM) alone. Meanwhile, the (01) plane is reported to possess a high density of dangling bonds, which facilitates the formation of ohmic contacts and highlights its potential as a device substrate. In this study, unintentionally doped (UID) β‐ Ga 2 O 3 single crystals with (001) and (01) orientations were successfully grown using the EFG method, and their orientation‐dependent properties were comparatively investigated. Structural analyses confirm a single (100) reflection twin ( M (100) ), where c * = [001]* transformed into c * twin = M (100) [001]* = [−1, 0, 1]* = (01), maintaining c ‐axis alignment twin mirror‐reflecting planes. The results enable rapid and nondestructive orientation identification and highlight the substrate potential of the (01) plane for device applications.

  • Open Access

    Optimization of Seed Crystal Stability at the Initial Growth Stage Depending on Heating Ramp Rates and Gas Flow Channels of SiC Source Powder for Growth of 8-inch N- Type 4H-SiC Single Crystal

    by Chae Young Lee, Su Ho Kim, Jung Woo Choi, Myung Ok Kyun, Jung Gyu Kim, Kap Ryeol Ku, Yeon Suk Jang, Jung Gon Kim, Won Jae Lee

    Seed crystal stabilization during the initial stage of 200-mm 4H-SiC crystal growth is critical for achieving high-quality wafers with large diameters. This study investigated the effects of heating ramp rates (0 - 6 °C/min) and SiC source powder porosity through both simulation and experimental approaches. Low ramp rates resulted in surface degradation of the seed crystal, whereas high ramp rates induced significant thermal stress, leading to cracking. Optimal ramp rates of 3 - 5 °C/min significantly minimized damage caused by seed crystal loss. Furthermore, high-porosity source powder facilitated adequate gas transport channels, thereby enhancing seed crystal stability. Crystals grown under these optimized conditions demonstrated improved edge morphology, absence of polycrystalline inclusions, and low dislocation densities, with threading screw dislocations (TSD) below 500 cm -2 and basal plane dislocations (BPD) below 1,000 cm -2 . These results demonstrate that precise control of thermal parameters and source powder porosity offers an effective strategy for stable seed attachment and reproducible growth of high-quality, large-diameter SiC single crystals.

  • Open Access

    High-Quality SiC Crystal Growth by Cooldown Rate Control at Cooling Stage

    by Chae Young Lee, Su Ho Kim, Seung Jun Lee, Jong Hwi Park, Jung Woo Choi, Hyong Suk Lee, Jung Gyu Kim, Kap Ryeol Ku, Ye Jin Choi, Won Jae Lee

    Thermoelastic stress generated within SiC crystals during the cooling process can induce various types of dislocation defects. In this study, a newly designed cooling protocol was proposed to investigate the correlation between cooldown rate and defect formation in 4H-SiC single crystals. Three distinct cooldown rates, 10~30 °C/min, 1~5 °C/min, and less than 1 °C/min, were applied to assess their impact on the development of thermoelastic stress and resulting crystal quality. Notable variations in ingot color and surface morphology were observed depending on the applied cooldown rate. Dislocation types, including basal plane dislocations (BPDs), threading edge dislocations (TEDs), and threading screw dislocations (TSDs), were quantified through etch pit density (EPD) measurements after molten KOH etching at 600 °C for 14 minutes. The results indicate that higher cooldown rates led to an increase in BPD density due to enhanced plastic deformation, while lower cooldown rates resulted in higher TED and TSD densities, likely due to increased thermal stress. These findings demonstrate that precise control of the cooldown rate is critical for suppressing thermoelastic stress and minimizing defect densities in SiC crystal growth.


  • Open Access

    Optimization of Heat Transfer Design for High Quality 4H-SiC Ingot Growth

    by Seung Jun Lee, Su Ho Kim, Chae Young Lee, Jong Hwi Park, Jung Woo Choi, Hyong Suk Lee, Jung Gyu Kim, Kap Ryeol Ku, Min Kyu Kang, Won Jae Lee

    At the high growth temperatures of the PVT method, thermal radiation from the graphite crucible surface to the seed region is the dominant mode of heat transfer. In this study, we propose a newly designed crucible structure with a thinner graphite wall compared to the conventional design for SiC crystal growth. The SiC ingot grown using the conventional crucible exhibited the smallest thickness variation (flat top surface) between the center and the edge of the ingot, accompanied by polytype inclusions, which led to an increase in defect density. In contrast, SiC ingots grown using the newly designed crucibles (Design A and Design B) showed a convex top surface and a significantly lower defect density due to the improved heat transfer efficiency. Thinning the graphite crucible wall helps maintain a relatively higher temperature at the seed edge region, thereby effectively enhancing thermal radiation in the radial direction inside the crucible. These results indicate that thermal radiation in the radial direction can be achieved through appropriate optimization of the graphite wall thickness.


  • Open Access

    Filling-Design Effect of Powder Source in the Crucible on SiC Single-Crystal Growth

    by Min Kyu Kang, Gi Uk Lee, Ye Jin Choi, Gyeoung Jun Song, Na Kyeoung Kim, Mi Seon Park, Kwang Hee Jung, Won Jae Lee

    An effective powder consumption is indispensable for enlarging the diameter and thickness of SiC crystals. We employed three types of filling designs for SiC source powder with different distances between the surface of the seed and the source powder. To maintain the shape of the designs, the SiC source powder was heat-treated in an Ar atmosphere at 680 torr within a temperature range of 1500 to 1600°C. The SiC source powder consumption and contribution to growth in well-structured layouts increased due to the increase in the surface area of SiC source powder, despite its lower initial powder filling. The numerical simulation showed that the well-structured layouts with a higher surface area of SiC source powder have a higher partial pressure of Si and SiC2 gases (supersaturation of these gas phases) near the seed region compared to the without well-structured layouts. The computed tomography (CT) analysis of the cross-section of SiC source powder after the growth run clearly showed that the source powder was previously sublimated at the region of the crucible wall, and recrystallization at the surface region of the source powder physically retarded the pathway of SiC source gases to the region of the SiC seed crystal. The newly designed well-structured layouts of the source powder have an economical advantage in achieving effective powder consumption during crystal growth.

  • Open Access

    Process Gas Control for High-Resistance HPSI-SiC Growth

    by Seung Jun Lee, Su Ho Kim, Chae Young Lee, Jong Hwi Park, Jung Woo Choi, Jung Gyu Kim, Kap Ryeol Ku, Gi Uk Lee, Won Jae Lee

    In this study, we tried to grow SiC ingots with high resistivity and polytype stability with adoption hydrogen mixed gas flow to the PVT method. Three different types of growth atmosphere of N2+Ar, H/Ar ratio:10% and 30% were employed. The polytype inclusion, crystal shape and transparency, and their resistivity were systematically investigated by UVF images, exposing backlighting, and high resistivity analysis using COREMA (Contactless Resistivity Mapper), respectively. The SiC ingot grown with adoption N2+Ar exhibited a suppression of polytype inclusion, a convex shape and a lower resistivity. In contrast, the SiC ingot with more higher H/Ar ratio of 30% than that of 10% shows no polytype inclusion and highest resistivity of 1.7E11mΩ∙cm. The growth atmosphere of relative higher H/Ar ratio in SiC crystal growth could be led the way to manufacture HPSI (high-purity semi-insulating)-SiC single crystal with polytype stability.


  • Quality improvement of SiC single crystal by modification of hot zone design adoption with denser graphite insulation in PVT growth

    by Seung Jun Lee, Su Ho Kim, Chae Young Lee, Jong Hwi Park, Jung Woo Choi, Kap Ryeol Ku, Jung Gon Kim, Won Jae Lee


  • Open Access

    Growths of SiC Single Crystals Using the Physical Vapor Transport Method with Crushed CVD-SiC Blocks Under High Vertical Temperature Gradients

    by Ju-Hyeong Sun, Jae-Hyeon Park, Si-Young Bae, Yun-Ji Shin, Yong-Jin Kwon, Won-Jae Lee, Se-Hun Kwon, Seong-Min Jeong

    A recent study reported the rapid growth of SiC single crystals of ~1.5 mm/h using high-purity SiC sources obtained by recycling CVD-SiC blocks used as materials in semiconductor processes. This method has gained attention as a way to improve the productivity of the physical vapor transport (PVT) method, widely used for manufacturing single crystal substrates for power semiconductors. When recycling CVD-SiC blocks by crushing them for use as sources for growing SiC single crystals, the properties and the particle size distribution of the material differ from those of conventional commercial SiC powders, making it necessary to study their effects. Therefore, in this study, SiC single crystals were grown using the PVT method with crushed CVD-SiC blocks of various sizes as the source material, and the growth behavior was analyzed. Simulation results of the temperature distribution in the PVT system confirmed that using large, crushed blocks as the SiC source material generates a greater temperature gradient within the source compared to conventional commercial SiC powder, making it advantageous for rapid growth processes. Additionally, when the large, crushed blocks were vertically aligned, good crystal quality was experimentally achieved at high growth rates, even under non-optimized growth conditions.


  • Advanced HVPE sublimation sandwich method for Si layer formation on SiC substrates

    by Seonwoo Park, Kyoung Hwa Kim, Suhyun Mun, Injun Jeon, Seon Jin Mun, Young-Hun Cho, Jeongbin Heo, Min Yang, Hyung Soo Ahn, Hunsoo Jeon, et al.

  • Open Access

    The Role of Air-Pocket in Crucible Structure for High Quality SiC Crystal Growth

    by Seung Jun Lee, Su Ho Kim, Jung Woo Choi, Jong Hwi Park, Jung Gyu Kim, Kap Ryeol Ku, Ha Lin Lee, Gi Uk Lee, Won Jae Lee

    The modified design using an air-pocket existing on inside of crucible has been proposed for the growth of 6-inch SiC single crystal. The actual growth has been performed for conventional, focus ring design and modified hot-zone designs under the same growth conditions and then three SiC crystals were systematically compared in terms of crystal quality. Since stacking faults and polytype inclusions, which could cause dislocation formation, were suppressed by the suitable C/Si ratio control, it was possible to grow SiC ingots with reduced defect density and excellent crystal quality with crucible structures proposed in this study.