Yu Zhang
Research Subjects
Research Interests
Yu Zhang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Blaise Ravelo
Nanjing University of Information Science & Technology (NUIST) Nanjing China
1 shared publication - Dongjie Chen
Basic Courses Department, Zhejiang Police College, Hangzhou, China
1 shared publication - Fayu Wan
Nanjing University of Information Science and Technology
1 shared publication - Feng He
School of Physics, Beijing Institute of Technology, Beijing 100081, People’s Republic of China
1 shared publication - Gaofeng Mei
Beijing Orient Institute of Measurement and Test, Beijing, China
1 shared publication - Gaosheng He
School of Physics, Beijing Institute of Technology 1 , Beijing 100081, People's Republic of China
1 shared publication
Latest Publications
- 13 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-13
Charged Device Model ESD Sensitivity Tester Design and Application
This paper develops an electrostatic device (ESD) tester with particularly high sensitivity for the charged device model (CDM) by incorporating empirical equivalent circuit (EC) parameters. The tester is implemented by using software and hardware system based on the STM32® microcontroller The tester feasibility study involves circuit theoretical analysis and simulation enabling to investigate the influence of EC parameters on the discharge signal waveform. High-precision and automated ESD sensitivity are utilized to develop the proposed testing system. As proof of concept, various common electronic components are tested. The performed experiment reveals that the CDM discharge signal is influenced not only by the DUT’s capacitance, but also by the packaging structure and pins for different functions. The explored measurement results highlight the importance of considering different pins for electronic device ESD protection neasures. The present study is industrially useful to enhance the ESD immunity during the design of electronic devices or chips by considering their circuit connections.
- 13 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-13
Charged Device Model ESD Sensitivity Tester Design and Application
This paper develops an electrostatic device (ESD) tester with particularly high sensitivity for the charged device model (CDM) by incorporating empirical equivalent circuit (EC) parameters. The tester is implemented by using software and hardware system based on the STM32® microcontroller The tester feasibility study involves circuit theoretical analysis and simulation enabling to investigate the influence of EC parameters on the discharge signal waveform. High-precision and automated ESD sensitivity are utilized to develop the proposed testing system. As proof of concept, various common electronic components are tested. The performed experiment reveals that the CDM discharge signal is influenced not only by the DUT’s capacitance, but also by the packaging structure and pins for different functions. The explored measurement results highlight the importance of considering different pins for electronic device ESD protection neasures. The present study is industrially useful to enhance the ESD immunity during the design of electronic devices or chips by considering their circuit connections.
- Open Access
- 1 August 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (8)
Interaction between atmospheric pressure plasma jet and target
Interactions of floating potential on metal and dielectric targets with He atmospheric pressure plasma jet (APPJ) were studied in this paper. The APPJ is generated in a needle-ring corona-dielectric barrier discharge configuration, driven by a sinusoidal voltage. The characteristics of APPJ were assessed through electrical and optical examinations, and the time-average electrostatic voltage on the targets was measured using both contact and non-contact electrostatic voltmeters. It was found that both metal and dielectric targets can promote the jet development and speed up the jet velocity. During the negative half-cycle, the “plasma cluster” propagates from the target toward the ground electrode and then “merges” with the forward plasma jet, leading to a reversed development of jet. The two targets follow a similar pattern on the surface electrostatic voltage, that is, initially in a positive polarity whose amplitude first increases and then decreases and transits to negative polarity with an increase in the applied voltage. But there are also some minor differences between the two targets, e.g., the metallic target can change the discharge pattern and reduces the discharge current under certain conditions.
- 1 August 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (8)
Open AccessInteraction between atmospheric pressure plasma jet and target
Interactions of floating potential on metal and dielectric targets with He atmospheric pressure plasma jet (APPJ) were studied in this paper. The APPJ is generated in a needle-ring corona-dielectric barrier discharge configuration, driven by a sinusoidal voltage. The characteristics of APPJ were assessed through electrical and optical examinations, and the time-average electrostatic voltage on the targets was measured using both contact and non-contact electrostatic voltmeters. It was found that both metal and dielectric targets can promote the jet development and speed up the jet velocity. During the negative half-cycle, the “plasma cluster” propagates from the target toward the ground electrode and then “merges” with the forward plasma jet, leading to a reversed development of jet. The two targets follow a similar pattern on the surface electrostatic voltage, that is, initially in a positive polarity whose amplitude first increases and then decreases and transits to negative polarity with an increase in the applied voltage. But there are also some minor differences between the two targets, e.g., the metallic target can change the discharge pattern and reduces the discharge current under certain conditions.
- Open Access
- 30 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 5147-5159
Iterative Learning Control for High-Order Systems With Arbitrary Initial Shifts
In this paper, two iterative learning control methods are proposed for the different high-order systems with arbitrary initial shifts. The tracking errors caused by nonzero initial shifts are easily detected when applying conventional learning algorithms. But this defect is overcome through applying a step-by-step rectifying controller with initial initial rectifying action introduced in a small interval. It demonstrates the improvement of tracking performance and shows the robustness with respect to the stochastic initial shifts. Finally, simulation results are presented to illustrate the effectiveness of the stated algorithms.
- 30 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 5147-5159
Open AccessIterative Learning Control for High-Order Systems With Arbitrary Initial Shifts
In this paper, two iterative learning control methods are proposed for the different high-order systems with arbitrary initial shifts. The tracking errors caused by nonzero initial shifts are easily detected when applying conventional learning algorithms. But this defect is overcome through applying a step-by-step rectifying controller with initial initial rectifying action introduced in a small interval. It demonstrates the improvement of tracking performance and shows the robustness with respect to the stochastic initial shifts. Finally, simulation results are presented to illustrate the effectiveness of the stated algorithms.