Ehsan Sabah Al-Ameen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ehsan Sabah Al-Ameen has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Ali Farhan Ogaili
Mechanical Engineering Department, College of Engineering, Mustansiriyah University, Baghdad, Iraq
3 shared publications - Zaineb Waired Metteb
Mechanical Engineering Department, College of Engineering, Mustansiriyah University, Baghdad, Iraq
2 shared publications - Abeer K. Abd
Iraqi Ministry of Transport, Baghdad, Iraq
1 shared publication - Ammar Fadhil Hussein Al-Maliki
Mechanical Engineering Department, College of Engineering, Mustansiriyah University, Baghdad, Iraq
1 shared publication Fadhel Abbas Abdalla
1 shared publicationFadhel Abbas Abdulla
Mechanical Engineering Dept Mechanical Engineering Dept The University of Mustansiriyah-BAGHDAD-IRAQ University of Mustansiriyah BAGHDAD-IRAQ
1 shared publication
Latest Publications
- Open Access
- 1 May 2026
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 30 (3) , 324-331
Design and Test an Educational Model of a Robotic Arm on an Experimental Platform
A robotic arm with five degrees of freedom has been developed for use in learning laboratories. The arm's movements were designed and simulated in SOLIDWorks and LabVIEW. The LabVIEW Softmotion was used to impose motion constraints on the model. An Arduino Mega microcontroller was used to manipulate the servo motors in the joints. After the design and simulation, the system was implemented on a laboratory setup. The following steps were then specified to verify the results of the LabVIEW-designed model with the real physical laboratory. These tests were the transfer of mass between two predetermined points along a certain direction. Its limitations were actuator torque and arm stability limitations. Lastly, the comparison between the physical setup and the model showed high accuracy and performance in the execution of the movements. This study’s findings show a qualitative enhancement in education laboratory equipment and extend to the establishment of an integrated learning system that connects the simulated model to the real laboratory systems.
- 1 May 2026
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 30 (3) , 324-331
Open AccessDesign and Test an Educational Model of a Robotic Arm on an Experimental Platform
A robotic arm with five degrees of freedom has been developed for use in learning laboratories. The arm's movements were designed and simulated in SOLIDWorks and LabVIEW. The LabVIEW Softmotion was used to impose motion constraints on the model. An Arduino Mega microcontroller was used to manipulate the servo motors in the joints. After the design and simulation, the system was implemented on a laboratory setup. The following steps were then specified to verify the results of the LabVIEW-designed model with the real physical laboratory. These tests were the transfer of mass between two predetermined points along a certain direction. Its limitations were actuator torque and arm stability limitations. Lastly, the comparison between the physical setup and the model showed high accuracy and performance in the execution of the movements. This study’s findings show a qualitative enhancement in education laboratory equipment and extend to the establishment of an integrated learning system that connects the simulated model to the real laboratory systems.
- 11 November 2024
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 87 (1) , 73-88
WASTE EGGSHELL AND SAWDUST AS REINFORCEMENTS FOR SUSTAINABLE POLYESTER COMPOSITES: MECHANICAL CHARACTERIZATION AND ENVIRONMENTAL DURABILITY ASSESSMENT
This research endeavor undertakes an experimental investigation into the bending and tensile properties of polyester composites reinforced with waste eggshell powder and sawdust particles at 35 wt.%. Valorizing these waste materials as reinforcements contributes to sustainable practices, waste minimization, and environmental pollution mitigation. Composite samples were fabricated using hand lay-up and compression molding techniques. The effects of environmental exposure to water, acidic, and basic media immersion on the mechanical performance were evaluated to assess durability. Experimental characterization through tensile and three-point bending tests determined mechanical properties, stress-strain behavior, and failure mechanisms. Additionally, finite element analysis (FEA) simulations complemented the experiments by providing insights into stress distributions, deformations, and potential failure initiation sites within the composites under flexural loading. The computational models accurately captured the reinforcing effects of the waste materials and the degradation induced by environmental exposure, validating the experimental trends. Incorporating waste natural fibers significantly enhanced polyester's bending strength by 140% (sawdust) and 75% (eggshell), and tensile strength by 13% (sawdust) and 10% (eggshell). However, environmental exposure degraded properties to varying extents, with water immersion reducing tensile strength by 63% (sawdust) and 3% (eggshell), and flexural strength by 63% (sawdust) and 3% (eggshell). The acidic medium caused 58% (sawdust) and 23% (eggshell) reductions in tensile strength, and similar flexural strength degradations. Strikingly, the basic medium decreased eggshell composite tensile strength by 170% and flexural strength by 6%, while sawdust composite strengths declined by 44%.
- 11 November 2024
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 87 (1) , 73-88
WASTE EGGSHELL AND SAWDUST AS REINFORCEMENTS FOR SUSTAINABLE POLYESTER COMPOSITES: MECHANICAL CHARACTERIZATION AND ENVIRONMENTAL DURABILITY ASSESSMENT
This research endeavor undertakes an experimental investigation into the bending and tensile properties of polyester composites reinforced with waste eggshell powder and sawdust particles at 35 wt.%. Valorizing these waste materials as reinforcements contributes to sustainable practices, waste minimization, and environmental pollution mitigation. Composite samples were fabricated using hand lay-up and compression molding techniques. The effects of environmental exposure to water, acidic, and basic media immersion on the mechanical performance were evaluated to assess durability. Experimental characterization through tensile and three-point bending tests determined mechanical properties, stress-strain behavior, and failure mechanisms. Additionally, finite element analysis (FEA) simulations complemented the experiments by providing insights into stress distributions, deformations, and potential failure initiation sites within the composites under flexural loading. The computational models accurately captured the reinforcing effects of the waste materials and the degradation induced by environmental exposure, validating the experimental trends. Incorporating waste natural fibers significantly enhanced polyester's bending strength by 140% (sawdust) and 75% (eggshell), and tensile strength by 13% (sawdust) and 10% (eggshell). However, environmental exposure degraded properties to varying extents, with water immersion reducing tensile strength by 63% (sawdust) and 3% (eggshell), and flexural strength by 63% (sawdust) and 3% (eggshell). The acidic medium caused 58% (sawdust) and 23% (eggshell) reductions in tensile strength, and similar flexural strength degradations. Strikingly, the basic medium decreased eggshell composite tensile strength by 170% and flexural strength by 6%, while sawdust composite strengths declined by 44%.
- Open Access
- 1 November 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 928 (2) , 022147
Study of the Bending Characteristics in Composite Sandwich Structures – A Review
In several applications reaching from satellite, ships, aircraft, vehicles, railcars, bond construction and much extra, using sandwich constructions have increased rapidly in different fields. The aim of the subsequent paper is to include an overall summary to sandwich construction and explanation of mechanics structural including forms of actuating loads, failure modes found in sandwich panels and standard three-point bending study of sandwich construction.
- 1 November 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 928 (2) , 022147
Open AccessStudy of the Bending Characteristics in Composite Sandwich Structures – A Review
In several applications reaching from satellite, ships, aircraft, vehicles, railcars, bond construction and much extra, using sandwich constructions have increased rapidly in different fields. The aim of the subsequent paper is to include an overall summary to sandwich construction and explanation of mechanics structural including forms of actuating loads, failure modes found in sandwich panels and standard three-point bending study of sandwich construction.
- 25 March 2020
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2213 (1) , 020067
Mechanical properties of recycled plastic waste with the polyester
In this paper, nylon waste from PET and HDPE were used after its’ cutting in different forms (fibers and particles) and then mixed with polyester. The mechanical properties (tensile and compression) were studied. It is found that when adding the nylon waste to polyester, the stress that the material can bear is reduced. In contrast the strain increased in most tests, and thus can be used in many applications and on the other hand is considered it an important way for waste disposal a safety way and harmless to the environment and useful at the same time.
- 25 March 2020
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2213 (1) , 020067
Mechanical properties of recycled plastic waste with the polyester
In this paper, nylon waste from PET and HDPE were used after its’ cutting in different forms (fibers and particles) and then mixed with polyester. The mechanical properties (tensile and compression) were studied. It is found that when adding the nylon waste to polyester, the stress that the material can bear is reduced. In contrast the strain increased in most tests, and thus can be used in many applications and on the other hand is considered it an important way for waste disposal a safety way and harmless to the environment and useful at the same time.
- Open Access
- 1 January 2020
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Materials Science
- Vol. 7 (1) , 93-102
Evaluation of mechanical and electrical properties of GFRP composite strengthened with hybrid nanomaterial fillers
- 1 January 2020
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Materials Science
- Vol. 7 (1) , 93-102
Open AccessEvaluation of mechanical and electrical properties of GFRP composite strengthened with hybrid nanomaterial fillers
- Open Access
- 12 November 2019
- Published by International University of Sarajevo in Periodicals of Engineering and Natural Sciences (PEN)
- Vol. 7 (4) , 1698-1709
An experimental study for different types of natural fiber reinforced composite material
An experimental study for different types of natural fiber reinforced composite material
- 12 November 2019
- Published by International University of Sarajevo in Periodicals of Engineering and Natural Sciences (PEN)
- Vol. 7 (4) , 1698-1709
Open AccessAn experimental study for different types of natural fiber reinforced composite material
An experimental study for different types of natural fiber reinforced composite material
- 1 March 2018
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 22 (02) , 11-19
THE EFFECT OF BIAXIAL STATIC LOADS ON CRACK BEHAVIOR IN DIFFERENT COMPOSITE MATERIAL SAMPLES
- 1 March 2018
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 22 (02) , 11-19
THE EFFECT OF BIAXIAL STATIC LOADS ON CRACK BEHAVIOR IN DIFFERENT COMPOSITE MATERIAL SAMPLES
- 1 January 2018
- Published by Transstellar Journal Publications and Research Consultancy Private Limited in International Journal of Mechanical and Production Engineering Research and Development
- Vol. 8 (2) , 1235-1242
The Effect of Internal Pressure and Temperature on Hoop Strain Behavior in Spherical Composite Shell
- 1 January 2018
- Published by Transstellar Journal Publications and Research Consultancy Private Limited in International Journal of Mechanical and Production Engineering Research and Development
- Vol. 8 (2) , 1235-1242
The Effect of Internal Pressure and Temperature on Hoop Strain Behavior in Spherical Composite Shell