Thomas J. Brumm
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thomas J. Brumm has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
Steven Mickelson
6 shared publicationsCharles R. Hurburgh
Department of Agricultural and Biosystems Engineering Iowa State University Ames 50011 Iowa
4 shared publicationsCarl J. Bern
3 shared publicationsPatricia Harms
3 shared publicationsC. J. Bern
2 shared publicationsC. R. Hurburgh
Department of Agricultural Engineering Iowa State University 219C Davidson Hall Ames Iowa 50011
2 shared publications
Latest Publications
- Open Access
- 16 November 2021
- Published by Universidad San Francisco De Quito in ACI Avances en Ciencias e Ingenierías
- Vol. 13 (2) , 23
Fast Pyrolysis Biochar Flammability behavior for Handling and Storage
Biochar is a fairly new material in the research arena with limited information on safety aspects related to transportation, storage, disposal or field application methods. The objective of this research was to assess the flammability characteristics of fast pyrolysis biochars with test methods EPA 1030 and ASTM 4982. Results indicated that biochar is a non-flammable substance when tested with EPA 1030 ignitability of solids. However, when tested with ASTM D4982, a fast screening method, biochars showed potential risks of flammability. However, the addition of 20-50% moisture reduced any flammability concern. Fast pyrolysis biochar was more prone to be flammable than traditional charcoal and slow pyrolysis biochar tested in this study. Still, fast pyrolysis biochars presented lower flammability potential (ASTM 4982) in comparison to its precursor biomass. The flammability propagation measured with EPA 1030, had high correlations with oxygen content and surface area of the fast pyrolysis biochar. The combustion reaction of fast pyrolysis biochar is a flameless combustion process, with a slow burning rate, and most commonly exhibiting a hot ember smoldering propagation front. This paper illustrates the necessity of performing recurring tests due to biochar’s intrinsic variability stemming from the different modes of production and feedstock used.
- 16 November 2021
- Published by Universidad San Francisco De Quito in ACI Avances en Ciencias e Ingenierías
- Vol. 13 (2) , 23
Open AccessFast Pyrolysis Biochar Flammability behavior for Handling and Storage
Biochar is a fairly new material in the research arena with limited information on safety aspects related to transportation, storage, disposal or field application methods. The objective of this research was to assess the flammability characteristics of fast pyrolysis biochars with test methods EPA 1030 and ASTM 4982. Results indicated that biochar is a non-flammable substance when tested with EPA 1030 ignitability of solids. However, when tested with ASTM D4982, a fast screening method, biochars showed potential risks of flammability. However, the addition of 20-50% moisture reduced any flammability concern. Fast pyrolysis biochar was more prone to be flammable than traditional charcoal and slow pyrolysis biochar tested in this study. Still, fast pyrolysis biochars presented lower flammability potential (ASTM 4982) in comparison to its precursor biomass. The flammability propagation measured with EPA 1030, had high correlations with oxygen content and surface area of the fast pyrolysis biochar. The combustion reaction of fast pyrolysis biochar is a flameless combustion process, with a slow burning rate, and most commonly exhibiting a hot ember smoldering propagation front. This paper illustrates the necessity of performing recurring tests due to biochar’s intrinsic variability stemming from the different modes of production and feedstock used.
- 1 September 2021
- Published by Elsevier in Journal of Stored Products Research
- Vol. 93
Evaluation of stirring to suppress weevils in stored maize
- 1 September 2021
- Published by Elsevier in Journal of Stored Products Research
- Vol. 93
Evaluation of stirring to suppress weevils in stored maize
- 21 June 2021
- Published by Wiley in Journal of Food Process Engineering
- Vol. 44 (9) , e13780
Drying turmeric (Curcuma longa L.) using far‐Infrared radiation: Drying characteristics and process optimization
This study investigated the turmeric drying characteristics and process parameters optimization for far‐infrared (FIR) radiation drying of turmeric. The initial moisture contents of the sliced wet turmeric samples were approximately 80 ± 0.12% (wb). The turmeric was exposed to 6.65, 5.97, 4.97, and 4.80 μm FIR radiation for 70, 30, 25, and 20 min, respectively. The moisture content and color (L*, a*, and b* values) of turmeric were measured during the experiment. The optimization experiments were conducted based on response surface methodology according to a central composite design with two independent variables: exposure time and FIR wavelength. The dependent variables considered were moisture content, curcumin content, energy consumption, and color‐changing index. The final moisture content and curcumin content were reduced with decreasing FIR radiation wavelength. FIR radiation drying of turmeric was observed to be a falling rate process. The optimal conditions were obtained with the FIR wavelength of 5.51 μm and exposure time of 21 min by applying the desirability function method. Under the optimal conditions, the predicted values of response variables, curcumin content, color‐changing index, energy consumption, and final moisture content were 3.26% (dry weight), 13.29, 2.51 kWh/g water, and 10.25% (wb). The desirability of 0.8157 under the optimal conditions further confirmed the validation of models. The results concluded that the FIR radiation could effectively apply for drying turmeric.Practical Applications: The far‐infrared radiation can be applied for turmeric drying on an industrial scale. The drying rates and color‐changing index of turmeric increased with decreasing far‐infrared wavelength and increasing far‐infrared exposure time. Curcumin was reduced by increasing the far‐infrared wavelength and far‐infrared exposure time. The wavelength of 5.51 μm and exposure time of 21 min was the optimal conditions for FIR drying of turmeric. Therefore, the industry can achieve the optimum quality of turmeric within a shorter period of time by applying this technique.
- 21 June 2021
- Published by Wiley in Journal of Food Process Engineering
- Vol. 44 (9) , e13780
Drying turmeric (Curcuma longa L.) using far‐Infrared radiation: Drying characteristics and process optimization
This study investigated the turmeric drying characteristics and process parameters optimization for far‐infrared (FIR) radiation drying of turmeric. The initial moisture contents of the sliced wet turmeric samples were approximately 80 ± 0.12% (wb). The turmeric was exposed to 6.65, 5.97, 4.97, and 4.80 μm FIR radiation for 70, 30, 25, and 20 min, respectively. The moisture content and color (L*, a*, and b* values) of turmeric were measured during the experiment. The optimization experiments were conducted based on response surface methodology according to a central composite design with two independent variables: exposure time and FIR wavelength. The dependent variables considered were moisture content, curcumin content, energy consumption, and color‐changing index. The final moisture content and curcumin content were reduced with decreasing FIR radiation wavelength. FIR radiation drying of turmeric was observed to be a falling rate process. The optimal conditions were obtained with the FIR wavelength of 5.51 μm and exposure time of 21 min by applying the desirability function method. Under the optimal conditions, the predicted values of response variables, curcumin content, color‐changing index, energy consumption, and final moisture content were 3.26% (dry weight), 13.29, 2.51 kWh/g water, and 10.25% (wb). The desirability of 0.8157 under the optimal conditions further confirmed the validation of models. The results concluded that the FIR radiation could effectively apply for drying turmeric.Practical Applications: The far‐infrared radiation can be applied for turmeric drying on an industrial scale. The drying rates and color‐changing index of turmeric increased with decreasing far‐infrared wavelength and increasing far‐infrared exposure time. Curcumin was reduced by increasing the far‐infrared wavelength and far‐infrared exposure time. The wavelength of 5.51 μm and exposure time of 21 min was the optimal conditions for FIR drying of turmeric. Therefore, the industry can achieve the optimum quality of turmeric within a shorter period of time by applying this technique.
- 4 September 2020
- Published by American Society for Engineering Education
- p. 22.961.1-22.961.16
Introducing Systems Thinking to the Engineer of 2020
- 4 September 2020
- Published by American Society for Engineering Education
- p. 22.961.1-22.961.16
Introducing Systems Thinking to the Engineer of 2020
- 4 September 2020
- Published by American Society for Engineering Education
- p. 23.578.1-23.578.20
Exploring Early College Credit Implications for Engineering
Exploring Early Credit Implications for EngineeringInterest in time-to-graduation and four-year graduation rates for undergraduate students hasincreased nationally over the past decade. Rising costs of higher education have contributed tothis interest. In response, states and families have pushed to increase the number of collegecredits students can earn prior to graduation from high school (through programs such asAdvanced Placement, International Baccalaureate, courses taken through an agreement withcommunity colleges or four-year schools, etc.). Some may argue that this trend is not positiveand lessens the integrity both of the high school diploma and the college degree experience.However, baccalaureate institutions of higher education must adapt to this new reality if theywant to address the concerns of cost, time-to-graduation, and four-year graduation rates forstudents with early college credit.Recognizing this trend, Midwestern University investigated the magnitude of the trend, thesuccess of students entering with early college credit (as measured by retention, grade pointaverage, graduation rates, time to graduation, and success in subsequent courses), studentacademic pursuits, and policy/procedural implications at Midwestern University. The studymethodology included both quantitative and qualitative analyses. Statistical analyses of studentrecords included descriptive statistics, regression, and propensity score matching. Enrolledstudents participated in surveys and focus groups about their experiences at MidwesternUniversity and the impact early credit had on those experiences. Interviews were also conductedwith faculty members, advisors, and administrators from across the university. The universitycatalog was reviewed to identify relevant policy and procedural issues.The results showed that engineering students at Midwestern University, compared to non-engineering students, were less likely to shorten their time to graduation by having early collegecredit. Contributing factors included the heavily course-sequenced nature of the engineeringcurriculum, the inclusion of engineering courses into the early years of engineering degreeprograms as an effort to increase retention, and the limited number of elective courses allowed inmany engineering degree programs. As more students direct from high school enter with collegecredits, it is critical that engineering colleges reflect upon their policies, procedures, curriculum,and course offerings to meet the changing reality. This paper will share university andengineering specific early credit data, including data on student success; discuss the curricular,policy, and procedural issues of early college credit; and share strategies to address these issues.
- 4 September 2020
- Published by American Society for Engineering Education
- p. 23.578.1-23.578.20
Exploring Early College Credit Implications for Engineering
Exploring Early Credit Implications for EngineeringInterest in time-to-graduation and four-year graduation rates for undergraduate students hasincreased nationally over the past decade. Rising costs of higher education have contributed tothis interest. In response, states and families have pushed to increase the number of collegecredits students can earn prior to graduation from high school (through programs such asAdvanced Placement, International Baccalaureate, courses taken through an agreement withcommunity colleges or four-year schools, etc.). Some may argue that this trend is not positiveand lessens the integrity both of the high school diploma and the college degree experience.However, baccalaureate institutions of higher education must adapt to this new reality if theywant to address the concerns of cost, time-to-graduation, and four-year graduation rates forstudents with early college credit.Recognizing this trend, Midwestern University investigated the magnitude of the trend, thesuccess of students entering with early college credit (as measured by retention, grade pointaverage, graduation rates, time to graduation, and success in subsequent courses), studentacademic pursuits, and policy/procedural implications at Midwestern University. The studymethodology included both quantitative and qualitative analyses. Statistical analyses of studentrecords included descriptive statistics, regression, and propensity score matching. Enrolledstudents participated in surveys and focus groups about their experiences at MidwesternUniversity and the impact early credit had on those experiences. Interviews were also conductedwith faculty members, advisors, and administrators from across the university. The universitycatalog was reviewed to identify relevant policy and procedural issues.The results showed that engineering students at Midwestern University, compared to non-engineering students, were less likely to shorten their time to graduation by having early collegecredit. Contributing factors included the heavily course-sequenced nature of the engineeringcurriculum, the inclusion of engineering courses into the early years of engineering degreeprograms as an effort to increase retention, and the limited number of elective courses allowed inmany engineering degree programs. As more students direct from high school enter with collegecredits, it is critical that engineering colleges reflect upon their policies, procedures, curriculum,and course offerings to meet the changing reality. This paper will share university andengineering specific early credit data, including data on student success; discuss the curricular,policy, and procedural issues of early college credit; and share strategies to address these issues.
- 3 September 2020
- Published by American Society for Engineering Education
- p. 15.299.1-15.299.11
Competency Based Assessment Of Engineering Technology Program Outcomes
Competency-Based Assessment of Engineering Technology Program Outcomes Abstract ABET1 is the preeminent organization in the U.S. for accreditation of 2- and 4-yr college-level educational programs in applied science, computing, engineering, and technology. ABET accreditation regimes require program outcomes assessment. The Technology Accreditation Commission (TAC) of ABET is charged with accrediting two- and four-yr Engineering Technology (ET) programs. The 4-year ET major at the University of Delaware is a general ET program; and, for the purposes of TAC of ABET accreditation2, must demonstrate its graduates have mastered the a through k program outcomes listed in TAC of ABET documentation for Criterion 3 of its General Criteria for Accrediting Engineering Technology Programs. The a through k program outcomes, which include such statements as: a. an appropriate mastery of the knowledge, techniques, skills and modern tools of their disciplines, and d. an ability to apply creativity in the design of systems, components or processes appropriate to program objectives, are notoriously difficult to assess because they require complex blends of interdependent skills, the evaluations of which may be influenced by considerable subjectivity. Iowa State University (ISU)3 has adopted a competency-based assessment approach to demonstrate program outcomes for Engineering Accreditation Commission (EAC) of ABET2 accreditation of all its engineering programs in addition to its programs in agricultural systems technology and industrial technology. The ISU technology programs are accredited by the Association of Technology, Management, and Applied Engineering4. In consultation with graduates and industry partners, ISU developed a set of 14 “workplace competencies.” Each competency was designed to be “clear, concise and independent of all others”3. Each competency is demonstrated by a “set of observable and measurable key actions.” The confounding that plagues assessment of the ABET a-k program outcomes is avoided, and a measure of objectivity is introduced. The ISU competencies were determined to be “necessary and sufficient to address the EAC of ABET a-k outcomes” 3, and a matrix mapping the ISU workplace competencies to the EAC of ABET a-k outcomes was developed. This paper describes the adaptation of ISU’s competency-based assessment approach for outcomes assessment and TAC of ABET accreditation of the University of Delaware’s ET program. University of Delaware student competencies, derived from the ISU student competencies, are mapped to the TAC of ABET a-k program outcomes. As with ISU’s approach, a student ePortfolio system is utilized. Evaluations of competencies are informed by the student’s performance in a “Discovery Learning Experience” – either a technical practicum in industry or an undergraduate research project.
- 3 September 2020
- Published by American Society for Engineering Education
- p. 15.299.1-15.299.11
Competency Based Assessment Of Engineering Technology Program Outcomes
Competency-Based Assessment of Engineering Technology Program Outcomes Abstract ABET1 is the preeminent organization in the U.S. for accreditation of 2- and 4-yr college-level educational programs in applied science, computing, engineering, and technology. ABET accreditation regimes require program outcomes assessment. The Technology Accreditation Commission (TAC) of ABET is charged with accrediting two- and four-yr Engineering Technology (ET) programs. The 4-year ET major at the University of Delaware is a general ET program; and, for the purposes of TAC of ABET accreditation2, must demonstrate its graduates have mastered the a through k program outcomes listed in TAC of ABET documentation for Criterion 3 of its General Criteria for Accrediting Engineering Technology Programs. The a through k program outcomes, which include such statements as: a. an appropriate mastery of the knowledge, techniques, skills and modern tools of their disciplines, and d. an ability to apply creativity in the design of systems, components or processes appropriate to program objectives, are notoriously difficult to assess because they require complex blends of interdependent skills, the evaluations of which may be influenced by considerable subjectivity. Iowa State University (ISU)3 has adopted a competency-based assessment approach to demonstrate program outcomes for Engineering Accreditation Commission (EAC) of ABET2 accreditation of all its engineering programs in addition to its programs in agricultural systems technology and industrial technology. The ISU technology programs are accredited by the Association of Technology, Management, and Applied Engineering4. In consultation with graduates and industry partners, ISU developed a set of 14 “workplace competencies.” Each competency was designed to be “clear, concise and independent of all others”3. Each competency is demonstrated by a “set of observable and measurable key actions.” The confounding that plagues assessment of the ABET a-k program outcomes is avoided, and a measure of objectivity is introduced. The ISU competencies were determined to be “necessary and sufficient to address the EAC of ABET a-k outcomes” 3, and a matrix mapping the ISU workplace competencies to the EAC of ABET a-k outcomes was developed. This paper describes the adaptation of ISU’s competency-based assessment approach for outcomes assessment and TAC of ABET accreditation of the University of Delaware’s ET program. University of Delaware student competencies, derived from the ISU student competencies, are mapped to the TAC of ABET a-k program outcomes. As with ISU’s approach, a student ePortfolio system is utilized. Evaluations of competencies are informed by the student’s performance in a “Discovery Learning Experience” – either a technical practicum in industry or an undergraduate research project.
- 3 September 2020
- Published by American Society for Engineering Education
- p. 8.1247.1-8.1247.16
Using Engineering Competency Feedback To Assess Agricultural Engineering Curriculum
- 3 September 2020
- Published by American Society for Engineering Education
- p. 8.1247.1-8.1247.16
Using Engineering Competency Feedback To Assess Agricultural Engineering Curriculum
- 3 September 2020
- Published by American Society for Engineering Education
- p. 6.383.1-6.383.8
Development Of Workplace Competencies Sufficient To Measure Abet Outcomes
Session 1608 Development of Workplace Competencies Sufficient to Measure ABET Outcomes S. K. Mickelson, L. F. Hanneman, R. Guardiola, and T. J. Brumm Iowa State University/Iowa State University/ Development Dimensions, International/Iowa State University Abstract The opening paragraphs of the ABET Engineering Criteria 2000 state: “To be considered for accreditation, engineering programs must prepare graduates for the practice of engineering at the professional level.” Criterion 3, Program Outcomes and Assessment, states, “Engineering programs must demonstrate that their graduates have…” and presents a list of eleven specific outcomes, now well known as, ABET (a-k) Outcomes. Each of the ABET (a-k) Outcomes is too complex to measure directly; several are interdependent. Eight of outcomes address “an ability to”; two address “understanding”; and only one addresses the graduates’ “knowledge”. The direct measurement of “an ability to…” presents challenges very different from those of measuring knowledge and understanding. Taking the unique approach of addressing the ABET (a-k) Outcomes as workplace competencies, Iowa State University (ISU) College of Engineering partnered with Development Dimensions International (DDI), Inc., a global provider of competency-based performance management tools and services, to develop the processes and products to support this approach. Using “critical incident” based data gathering, the College and DDI brought together approximately one hundred constituents, representing ISU faculty, partnering international faculty, co-op and intern students, employers, parents, and alumni to provide input to the design of the measurements of the ABET (a-k) Outcomes. From the analysis of the “critical incidents,” fourteen unique dimensions, called “ISU Competencies”, were identified as necessary and sufficient to measure the ABET (a-k) Outcomes. Each Competency has been clearly defined, independent of all the others. The fourteen ISU Competencies have been mapped to the ABET (a-k) Outcomes. For each Competency an independent set of observable and measurable Key Actions, which students may take to demonstrate their development, have been defined. An appropriate measurement approach has been identified for the Key Actions. Validation of the development process by the contributing constituents is in progress. Introduction The Accreditation Board for Engineering and Technology (ABET) has instituted fundamental changes in accreditation procedures. A shift in focus from traditional "inputs" metrics to defining and measuring what is expected of graduates is well into implementation1. Criterion 3, Program Outcomes and Assessment, states, “Engineering programs must demonstrate that their graduates have…” and “Proceedings of the 2001 American Society for Engineering Education Annual Conference & Exposition Copyright © 2001, American Society for Engineering Education”
- 3 September 2020
- Published by American Society for Engineering Education
- p. 6.383.1-6.383.8
Development Of Workplace Competencies Sufficient To Measure Abet Outcomes
Session 1608 Development of Workplace Competencies Sufficient to Measure ABET Outcomes S. K. Mickelson, L. F. Hanneman, R. Guardiola, and T. J. Brumm Iowa State University/Iowa State University/ Development Dimensions, International/Iowa State University Abstract The opening paragraphs of the ABET Engineering Criteria 2000 state: “To be considered for accreditation, engineering programs must prepare graduates for the practice of engineering at the professional level.” Criterion 3, Program Outcomes and Assessment, states, “Engineering programs must demonstrate that their graduates have…” and presents a list of eleven specific outcomes, now well known as, ABET (a-k) Outcomes. Each of the ABET (a-k) Outcomes is too complex to measure directly; several are interdependent. Eight of outcomes address “an ability to”; two address “understanding”; and only one addresses the graduates’ “knowledge”. The direct measurement of “an ability to…” presents challenges very different from those of measuring knowledge and understanding. Taking the unique approach of addressing the ABET (a-k) Outcomes as workplace competencies, Iowa State University (ISU) College of Engineering partnered with Development Dimensions International (DDI), Inc., a global provider of competency-based performance management tools and services, to develop the processes and products to support this approach. Using “critical incident” based data gathering, the College and DDI brought together approximately one hundred constituents, representing ISU faculty, partnering international faculty, co-op and intern students, employers, parents, and alumni to provide input to the design of the measurements of the ABET (a-k) Outcomes. From the analysis of the “critical incidents,” fourteen unique dimensions, called “ISU Competencies”, were identified as necessary and sufficient to measure the ABET (a-k) Outcomes. Each Competency has been clearly defined, independent of all the others. The fourteen ISU Competencies have been mapped to the ABET (a-k) Outcomes. For each Competency an independent set of observable and measurable Key Actions, which students may take to demonstrate their development, have been defined. An appropriate measurement approach has been identified for the Key Actions. Validation of the development process by the contributing constituents is in progress. Introduction The Accreditation Board for Engineering and Technology (ABET) has instituted fundamental changes in accreditation procedures. A shift in focus from traditional "inputs" metrics to defining and measuring what is expected of graduates is well into implementation1. Criterion 3, Program Outcomes and Assessment, states, “Engineering programs must demonstrate that their graduates have…” and “Proceedings of the 2001 American Society for Engineering Education Annual Conference & Exposition Copyright © 2001, American Society for Engineering Education”
- 3 September 2020
- Published by American Society for Engineering Education
- p. 6.1108.1-6.1108.11
Using Learning Community Course Links To Bring Meaning To The First Year Engineering Curriculum
The Iowa State University Department of Agricultural and Biosystems Engineering (ABE) has created a successful learning community for incoming ABE students. In this paper, we provide an overview of our learning community structure and describe the collaboration between the departments of ABE and English that has fostered a cross-disciplinary initiative that includes students writing papers relating to agriculture and engineering in composition and using newly learned technical writing skills for report writing in engineering graphics and design and engineering problem solving. Both quantitative and qualitative methods were employed to assess the ABE Learning Community. Results are reported, including survey data which reveals that on average, students agreed or strongly agreed that they developed or enhanced their team skills through collaborative assignments in their learning community classes, and on average, students agreed or strongly agreed that they are excited to be a part of the field of engineering and technology. Focus group data are also reported.
- 3 September 2020
- Published by American Society for Engineering Education
- p. 6.1108.1-6.1108.11
Using Learning Community Course Links To Bring Meaning To The First Year Engineering Curriculum
The Iowa State University Department of Agricultural and Biosystems Engineering (ABE) has created a successful learning community for incoming ABE students. In this paper, we provide an overview of our learning community structure and describe the collaboration between the departments of ABE and English that has fostered a cross-disciplinary initiative that includes students writing papers relating to agriculture and engineering in composition and using newly learned technical writing skills for report writing in engineering graphics and design and engineering problem solving. Both quantitative and qualitative methods were employed to assess the ABE Learning Community. Results are reported, including survey data which reveals that on average, students agreed or strongly agreed that they developed or enhanced their team skills through collaborative assignments in their learning community classes, and on average, students agreed or strongly agreed that they are excited to be a part of the field of engineering and technology. Focus group data are also reported.
- 3 September 2020
- Published by American Society for Engineering Education
- p. 6.251.1-6.251.12
Building Community For First And Second Year Students In The Agricultural And Biosystems Engineering Department At Iowa State University
A residence hall living community has provided a new way for our first- and second-year students in Agricultural and Biosystems Engineering (ABE) at Iowa State University to build community and to become involved members of our department. An optional component of our ABE First-Year Learning Community, the ABE Living Community was recently expanded to include second-year students to accommodate student requests. Not only does the living community offer a way for students to develop friendships, it also creates an environment well suited for academic work. Our paper includes an overview of our ABE living community, which includes both engineering and technology students. We developed this arrangement to strengthen students’ existing learning communities through additional interaction with ABE peers in a living community, to encourage interaction and collaboration between our two undergraduate student majors, and to increase interaction of these students with the ABE faculty. In addition, we present the results of our assessment, which includes a year-end survey, student responses to a writing prompt, and student focus groups.
- 3 September 2020
- Published by American Society for Engineering Education
- p. 6.251.1-6.251.12
Building Community For First And Second Year Students In The Agricultural And Biosystems Engineering Department At Iowa State University
A residence hall living community has provided a new way for our first- and second-year students in Agricultural and Biosystems Engineering (ABE) at Iowa State University to build community and to become involved members of our department. An optional component of our ABE First-Year Learning Community, the ABE Living Community was recently expanded to include second-year students to accommodate student requests. Not only does the living community offer a way for students to develop friendships, it also creates an environment well suited for academic work. Our paper includes an overview of our ABE living community, which includes both engineering and technology students. We developed this arrangement to strengthen students’ existing learning communities through additional interaction with ABE peers in a living community, to encourage interaction and collaboration between our two undergraduate student majors, and to increase interaction of these students with the ABE faculty. In addition, we present the results of our assessment, which includes a year-end survey, student responses to a writing prompt, and student focus groups.