Wiesław Wilczyński
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Wiesław Wilczyński has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Jan Szczygłowski
Faculty of Electrical Engineering , Czestochowa University of Technology , Czestochowa , Poland
6 shared publications - Krzysztof Chwastek
Faculty of Electrical Engineering, Czestochowa University of Technology, Czestochowa, Poland
4 shared publications - Mariusz Najgebauer
Faculty of Electrical Engineering, Częstochowa University of Technology, 42-201 Częstochowa, Poland
2 shared publications A. Roman
1 shared publicationA. Sheindlin
Joint Institute for High Temperatures of Russian Academy of Sciences
1 shared publication- A. Zhuk
Joint Institute for High Temperatures of Russian Academy of Sciences
1 shared publication
Latest Publications
- 1 June 2016
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 129 (6) , 1226-1229
Nanoscopic Investigation of Magnetic Thin Films by Means of Magnetic Force Microscopy Technique
- 1 June 2016
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 129 (6) , 1226-1229
Nanoscopic Investigation of Magnetic Thin Films by Means of Magnetic Force Microscopy Technique
- Open Access
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 113 (1) , 012009
Magnetic thin film deposition with pulsed magnetron sputtering: deposition rate and film thickness distribution
The goal of conducted study was an experimental determining the relations between technological parameters of magnetron sputtering process on deposition rate (R) and thickness uniformity of magnetic thin films. Planar Ni 79 Fe 16 Mo 5 target with a diameter of 100 mm was sputtered in argon (Ar) atmosphere. Deposition rate was measured in a function of gas pressure, target power and target-substrate distance. The highest value of R≈280 nm•min-1. The obtained results in deposition rate of magnetic film were compared to deposition rate of cooper (Cu), aluminum (Al), titanium (Ti) and titanium oxide (TiO x) and the deposition rate of Ni-Fe alloy were higher that Al and Ti. The film thickness distribution was measured for radial distance from the target centre ranging up to 60 mm and target-substrate distance ranging form 70 to 115 mm. Among others it was stated that for the larger value of target-substrate distance the larger uniform of film thickness are obtained.
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 113 (1) , 012009
Open AccessMagnetic thin film deposition with pulsed magnetron sputtering: deposition rate and film thickness distribution
The goal of conducted study was an experimental determining the relations between technological parameters of magnetron sputtering process on deposition rate (R) and thickness uniformity of magnetic thin films. Planar Ni 79 Fe 16 Mo 5 target with a diameter of 100 mm was sputtered in argon (Ar) atmosphere. Deposition rate was measured in a function of gas pressure, target power and target-substrate distance. The highest value of R≈280 nm•min-1. The obtained results in deposition rate of magnetic film were compared to deposition rate of cooper (Cu), aluminum (Al), titanium (Ti) and titanium oxide (TiO x) and the deposition rate of Ni-Fe alloy were higher that Al and Ti. The film thickness distribution was measured for radial distance from the target centre ranging up to 60 mm and target-substrate distance ranging form 70 to 115 mm. Among others it was stated that for the larger value of target-substrate distance the larger uniform of film thickness are obtained.
- 25 October 2013
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 44 (4) , 543-550
Hybrid energy storage system based on supercapacitors and Li-ion batteries
- 25 October 2013
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 44 (4) , 543-550
Hybrid energy storage system based on supercapacitors and Li-ion batteries
- 17 October 2012
- Published by Walter de Gruyter GmbH in Materials Science-Poland
- Vol. 30 (4) , 297-302
The influence of densification temperature and the size of powder particles on the properties of isotropic Nd-Fe-B magnets made of quenched ribbons
The influence of densification temperature and the size of powder particles on magnetization of remanence J r , coercivity J H c of hot-densified Nd-Fe-B magnets made of MQP-A quenched ribbons was investigated. A connection between magnetic properties, parameters of production process and microstructure of the magnet was confirmed. It was found that the remanence of isotropic magnet depends on temperature of hot densification process but is practically independent of the size of powder particles. On the other hand, the temperature of hot densification process and the size of powder particles have a substantial influence on coercivity.
- 17 October 2012
- Published by Walter de Gruyter GmbH in Materials Science-Poland
- Vol. 30 (4) , 297-302
The influence of densification temperature and the size of powder particles on the properties of isotropic Nd-Fe-B magnets made of quenched ribbons
The influence of densification temperature and the size of powder particles on magnetization of remanence J r , coercivity J H c of hot-densified Nd-Fe-B magnets made of MQP-A quenched ribbons was investigated. A connection between magnetic properties, parameters of production process and microstructure of the magnet was confirmed. It was found that the remanence of isotropic magnet depends on temperature of hot densification process but is practically independent of the size of powder particles. On the other hand, the temperature of hot densification process and the size of powder particles have a substantial influence on coercivity.
- Open Access
- 1 April 2012
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 121 (4) , 941-944
Minor Loops in the Harrison Model
- 1 April 2012
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 121 (4) , 941-944
Open AccessMinor Loops in the Harrison Model
- Open Access
Scaling Conception of Energy Loss' Separation in Soft Magnetic Materials
Data collapse enables comparison of measurement data measured in different laboratories on different samples. In the case of energy losses in Soft Magnetic Materials (SMM) the data collapse is possible to achieved only if the measurement data can be described by the two components formula. For more complicated cases we propose to perform data collapse's sequence in the two-dimensional subspaces $L_{i,i+1}$ spanned by the appropriate powers of frequency $\{f^{i},f^{i+1}\}$. Such approach enables the data comparison in the different two-dimensional subspaces. This idea has been tested with measurement data of the four SMM-s: amorphous alloy \textrm{Fe}_{78}\textrm{Si}_{13}\textrm{B}_{9}$, amorphous alloy $\textrm{Co}_{71.5} \textrm{Fe}_{2.5} \textrm{Mn}_{2} \textrm{Mo}_{1} \textrm{Si}_{9} \textrm{B}_{14}$, crystalline material -- oriented electrotechnical steel sheets 3% Si--Fe, iron--nickel alloy $79% \textrm{Ni}-\textrm{Fe}$. Intermediate calculations revealed interesting property of the energy losses in the cristalline and amorphous SMM-s which lead to the following hypothesis. Let $P_{tot\,1,2}=f_{1,2}(1+f_{1,2})$ be scaled two-components formula for the energy loss in SMM, where $f_{1,2}$ is the corresponding scaled frequency. Then the scaled energy losses' values in amorphous SMM are below the second order universal curve $P_{tot\,1,2}=f_{1,2}(1+f_{1,2})$, whereas the scaled energy losses' values in crystalline SMM are above that universal curve.Open AccessScaling Conception of Energy Loss' Separation in Soft Magnetic Materials
Data collapse enables comparison of measurement data measured in different laboratories on different samples. In the case of energy losses in Soft Magnetic Materials (SMM) the data collapse is possible to achieved only if the measurement data can be described by the two components formula. For more complicated cases we propose to perform data collapse's sequence in the two-dimensional subspaces $L_{i,i+1}$ spanned by the appropriate powers of frequency $\{f^{i},f^{i+1}\}$. Such approach enables the data comparison in the different two-dimensional subspaces. This idea has been tested with measurement data of the four SMM-s: amorphous alloy \textrm{Fe}_{78}\textrm{Si}_{13}\textrm{B}_{9}$, amorphous alloy $\textrm{Co}_{71.5} \textrm{Fe}_{2.5} \textrm{Mn}_{2} \textrm{Mo}_{1} \textrm{Si}_{9} \textrm{B}_{14}$, crystalline material -- oriented electrotechnical steel sheets 3% Si--Fe, iron--nickel alloy $79% \textrm{Ni}-\textrm{Fe}$. Intermediate calculations revealed interesting property of the energy losses in the cristalline and amorphous SMM-s which lead to the following hypothesis. Let $P_{tot\,1,2}=f_{1,2}(1+f_{1,2})$ be scaled two-components formula for the energy loss in SMM, where $f_{1,2}$ is the corresponding scaled frequency. Then the scaled energy losses' values in amorphous SMM are below the second order universal curve $P_{tot\,1,2}=f_{1,2}(1+f_{1,2})$, whereas the scaled energy losses' values in crystalline SMM are above that universal curve. - Open Access
- 1 March 2011
- Published by Polish Academy of Sciences Chancellery in Archives of Electrical Engineering
- Vol. 60 (1) , 59-66
The accuracy of loss prediction in magnetic materials
The paper presents a formula useful for prediction of loss density in soft magnetic materials, which takes into account multi-scale energy dissipation. A universal phenomenological P(B m , f) relationship is used for loss prediction in chosen soft magnetic materials. A bootstrap method is used to generate additional data points, what makes it possible to increase the prediction accuracy. A substantial accuracy improvement for estimated model parameters is obtained in the case, when additional data points are taken into account. The proposed description could be useful both for device designers and researchers involved in computational electromagnetism.
- 1 March 2011
- Published by Polish Academy of Sciences Chancellery in Archives of Electrical Engineering
- Vol. 60 (1) , 59-66
Open AccessThe accuracy of loss prediction in magnetic materials
The paper presents a formula useful for prediction of loss density in soft magnetic materials, which takes into account multi-scale energy dissipation. A universal phenomenological P(B m , f) relationship is used for loss prediction in chosen soft magnetic materials. A bootstrap method is used to generate additional data points, what makes it possible to increase the prediction accuracy. A substantial accuracy improvement for estimated model parameters is obtained in the case, when additional data points are taken into account. The proposed description could be useful both for device designers and researchers involved in computational electromagnetism.
- 30 April 2010
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 322 (7) , 799-803
Modelling magnetic properties of high silicon steel
- 30 April 2010
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 322 (7) , 799-803
Modelling magnetic properties of high silicon steel
- 8 May 2009
- Published by Emerald Publishing in COMPEL - The international journal for computation and mathematics in electrical and electronic engineering
- Vol. 28 (3) , 603-612
Modelling dynamic hysteresis loops in steel sheets
Purpose: The aim of the paper is to present a simple approach to modelling minor hysteresis loops in grain‐oriented steel sheets under quasi‐static and dynamic conditions. The hysteresis phenomenon is described with a recently developed hybrid model, which combines ideas inherent in the product Preisach model and the Jiles‐Atherton description. The dynamic effects due to eddy currents are taken into account in the description using a lagged response with respect to the input.Design/methodology/approach: It is assumed that some model parameters might be dependent on the level of relative magnetization within the material. Their dependencies could be given as power laws. The values of scaling coefficients in power laws are determined.Findings: A satisfactory agreement of experimental and modelled quasi‐static and dynamic hysteresis loops is obtained.Research limitations/implications: The present study provides a starting point for further verification of the approach for other classes of soft magnetic materials, which could be described with the developed model. At present, the approach to model minor loops by the update of model parameters is verified for the B‐sine excitation case.Practical implications: The “branch‐and‐bound” optimization algorithm is a useful tool for recovery of the values of both model parameters and scaling coefficients as well.Originality/value: The recently developed hybrid description of hysteresis phenomenon can be successfully extended to take into account symmetric minor loops. The developed approach could be a framework to develop a comprehensive description of magnetization phenomena in the future.
- 8 May 2009
- Published by Emerald Publishing in COMPEL - The international journal for computation and mathematics in electrical and electronic engineering
- Vol. 28 (3) , 603-612
Modelling dynamic hysteresis loops in steel sheets
Purpose: The aim of the paper is to present a simple approach to modelling minor hysteresis loops in grain‐oriented steel sheets under quasi‐static and dynamic conditions. The hysteresis phenomenon is described with a recently developed hybrid model, which combines ideas inherent in the product Preisach model and the Jiles‐Atherton description. The dynamic effects due to eddy currents are taken into account in the description using a lagged response with respect to the input.Design/methodology/approach: It is assumed that some model parameters might be dependent on the level of relative magnetization within the material. Their dependencies could be given as power laws. The values of scaling coefficients in power laws are determined.Findings: A satisfactory agreement of experimental and modelled quasi‐static and dynamic hysteresis loops is obtained.Research limitations/implications: The present study provides a starting point for further verification of the approach for other classes of soft magnetic materials, which could be described with the developed model. At present, the approach to model minor loops by the update of model parameters is verified for the B‐sine excitation case.Practical implications: The “branch‐and‐bound” optimization algorithm is a useful tool for recovery of the values of both model parameters and scaling coefficients as well.Originality/value: The recently developed hybrid description of hysteresis phenomenon can be successfully extended to take into account symmetric minor loops. The developed approach could be a framework to develop a comprehensive description of magnetization phenomena in the future.