Jung Hoon Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jung Hoon Kim has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Byung Wan Jo
Department of Civil and Environmental Engineering, Hanyang University, Seoul 04763, Korea
7 shared publications - Jun Ho Jo
Department of Civil and Environmental Engineering, Hanyang University, Seoul 04763, Korea
5 shared publications - Yun Sung Lee
Department of Civil and Environmental Engineering, Hanyang University, Seoul 04763, Korea
5 shared publications - Do Keun Kim
Research and Development Centre, Youngshine D&C, Gyeonggi-do 13487, Korea
4 shared publications - Rana Muhammad Asad Khan
Department of Mining Engineering, Pak-Austria Fachhochschule Institute of Applied Sciences and Technology, Haripur 22620, Pakistan
3 shared publications - Alvaro Pascual-Leone
Department of Neurology, Harvard Medical School, Boston, MA, United States
1 shared publication
Latest Publications
- Open Access
- 21 January 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (3) , 1102
Autonomous Detection System for Non-Hard-Hat Use at Construction Sites Using Sensor Technology
In this study, we present a novel method of detecting hard hat use on construction sites using a modified version of an off-the-shelf wearable device. The data-transmitting node of the device contained two sensors, a photoplethysmogram (PPG) and accelerometers (Acc), along with two modules, a global positioning system (GPS) and a low-power wide-area (LoRa) network module. All the components were embedded into a microcontroller unit (MCU) in addition to the power supply. The receiving node included a server that displayed the results via both the Internet of Things (IoT) and smartphones. The LoRa network connected two nodes so that it could function in larger areas such as construction sites at a relatively low cost. The proposed method analyzes the data from a PPG sensor located on the hard hat chin strap and automatically notifies a manager when a worker is not wearing the required hard hat at the site. In addition, by utilizing the PPG sensor data, a heart rate abnormality-detecting feature was added based on an age-adjusted maximum heart rate formula. In validation tests, various PPG sensor locations and shapes were studied, and the results demonstrated the smallest error in the circular shaped sensor located at the upper neck (0.56%). Finally, an IoT monitoring page was created to monitor heart rate abnormalities while identifying hard hat use violations via both PCs and smart phones.
- 21 January 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (3) , 1102
Open AccessAutonomous Detection System for Non-Hard-Hat Use at Construction Sites Using Sensor Technology
In this study, we present a novel method of detecting hard hat use on construction sites using a modified version of an off-the-shelf wearable device. The data-transmitting node of the device contained two sensors, a photoplethysmogram (PPG) and accelerometers (Acc), along with two modules, a global positioning system (GPS) and a low-power wide-area (LoRa) network module. All the components were embedded into a microcontroller unit (MCU) in addition to the power supply. The receiving node included a server that displayed the results via both the Internet of Things (IoT) and smartphones. The LoRa network connected two nodes so that it could function in larger areas such as construction sites at a relatively low cost. The proposed method analyzes the data from a PPG sensor located on the hard hat chin strap and automatically notifies a manager when a worker is not wearing the required hard hat at the site. In addition, by utilizing the PPG sensor data, a heart rate abnormality-detecting feature was added based on an age-adjusted maximum heart rate formula. In validation tests, various PPG sensor locations and shapes were studied, and the results demonstrated the smallest error in the circular shaped sensor located at the upper neck (0.56%). Finally, an IoT monitoring page was created to monitor heart rate abnormalities while identifying hard hat use violations via both PCs and smart phones.
- Open Access
Development of an IoT-Based Construction Worker Physiological Data Monitoring Platform at High Temperatures
This study presents an IoT-based construction worker physiological data monitoring platform using an off-the-shelf wearable smart band. The developed platform is designed for construction workers performing under high temperatures, and the platform is composed of two parts: an overall heat assessment (OHS) and a personal management system (PMS). OHS manages the breaktimes for groups of workers based using a thermal comfort index (TCI), as provided by the Korea Meteorological Administration (KMA), while PMS assesses the individual health risk level based on fuzzy theory using data acquired from a commercially available smart band. The device contains three sensors (PPG, Acc, and skin temperature), two modules (LoRa and GPS), and a power supply, which are embedded into a microcontroller (MCU). Thus, approved personnel can monitor the status as well as the current position of a construction worker via a PC or smartphone, and can make necessary decisions remotely. The platform was tested in both indoor and outdoor environment for reliability, achieved less than 1% of error, and received satisfactory feedback from on-site users.
Open AccessDevelopment of an IoT-Based Construction Worker Physiological Data Monitoring Platform at High Temperatures
This study presents an IoT-based construction worker physiological data monitoring platform using an off-the-shelf wearable smart band. The developed platform is designed for construction workers performing under high temperatures, and the platform is composed of two parts: an overall heat assessment (OHS) and a personal management system (PMS). OHS manages the breaktimes for groups of workers based using a thermal comfort index (TCI), as provided by the Korea Meteorological Administration (KMA), while PMS assesses the individual health risk level based on fuzzy theory using data acquired from a commercially available smart band. The device contains three sensors (PPG, Acc, and skin temperature), two modules (LoRa and GPS), and a power supply, which are embedded into a microcontroller (MCU). Thus, approved personnel can monitor the status as well as the current position of a construction worker via a PC or smartphone, and can make necessary decisions remotely. The platform was tested in both indoor and outdoor environment for reliability, achieved less than 1% of error, and received satisfactory feedback from on-site users.
- Open Access
- 28 July 2020
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 17 (15) , 5429
Implementation of IoT-Based Air Quality Monitoring System for Investigating Particulate Matter (PM10) in Subway Tunnels
Air quality monitoring for subway tunnels in South Korea is a topic of great interest because more than 8 million passengers per day use the subway, which has a concentration of particulate matter (PM10) greater than that of above ground. In this paper, an Internet of Things (IoT)-based air quality monitoring system, consisting of an air quality measurement device called Smart-Air, an IoT gateway, and a cloud computing web server, is presented to monitor the concentration of PM10 in subway tunnels. The goal of the system is to efficiently monitor air quality at any time and from anywhere by combining IoT and cloud computing technologies. This system was successfully implemented in Incheon’s subway tunnels to investigate levels of PM10. The concentration of particulate matter was greatest between the morning and afternoon rush hours. In addition, the residence time of PM10 increased as the depth of the monitoring location increased. During the experimentation period, the South Korean government implemented an air quality management system. An analysis was performed to follow up after implementation and assess how the change improved conditions. Based on the experiments, the system was efficient and effective at monitoring particulate matter for improving air quality in subway tunnels.
- 28 July 2020
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 17 (15) , 5429
Open AccessImplementation of IoT-Based Air Quality Monitoring System for Investigating Particulate Matter (PM10) in Subway Tunnels
Air quality monitoring for subway tunnels in South Korea is a topic of great interest because more than 8 million passengers per day use the subway, which has a concentration of particulate matter (PM10) greater than that of above ground. In this paper, an Internet of Things (IoT)-based air quality monitoring system, consisting of an air quality measurement device called Smart-Air, an IoT gateway, and a cloud computing web server, is presented to monitor the concentration of PM10 in subway tunnels. The goal of the system is to efficiently monitor air quality at any time and from anywhere by combining IoT and cloud computing technologies. This system was successfully implemented in Incheon’s subway tunnels to investigate levels of PM10. The concentration of particulate matter was greatest between the morning and afternoon rush hours. In addition, the residence time of PM10 increased as the depth of the monitoring location increased. During the experimentation period, the South Korean government implemented an air quality management system. An analysis was performed to follow up after implementation and assess how the change improved conditions. Based on the experiments, the system was efficient and effective at monitoring particulate matter for improving air quality in subway tunnels.
- Open Access
- 14 July 2020
- Published by Frontiers Media SA in Frontiers in Human Neuroscience
- Vol. 14, 249
Corrigendum: Interhemispheric and Intrahemispheric Connectivity From the Left Pars Opercularis Within the Language Network Is Modulated by Transcranial Stimulation in Healthy Subjects
Corrigendum: Interhemispheric and Intrahemispheric Connectivity From the Left Pars Opercularis Within the Language Network Is Modulated by Transcranial Stimulation in Healthy Subjects
- 14 July 2020
- Published by Frontiers Media SA in Frontiers in Human Neuroscience
- Vol. 14, 249
Open AccessCorrigendum: Interhemispheric and Intrahemispheric Connectivity From the Left Pars Opercularis Within the Language Network Is Modulated by Transcranial Stimulation in Healthy Subjects
Corrigendum: Interhemispheric and Intrahemispheric Connectivity From the Left Pars Opercularis Within the Language Network Is Modulated by Transcranial Stimulation in Healthy Subjects
- Top Cited PapersOpen Access
- 14 January 2020
- Published by Wiley in Journal of Sensors
- Vol. 2020, 1-14
Development of an IoT-Based Indoor Air Quality Monitoring Platform
In this paper, an IoT-based indoor air quality monitoring platform, consisting of an air quality-sensing device called “Smart-Air” and a web server, is demonstrated. This platform relies on an IoT and a cloud computing technology to monitor indoor air quality in anywhere and anytime. Smart-Air has been developed based on the IoT technology to efficiently monitor the air quality and transmit the data to a web server via LTE in real time. The device is composed of a microcontroller, pollutant detection sensors, and LTE modem. In the research, the device was designed to measure a concentration of aerosol, VOC, CO, CO2, and temperature-humidity to monitor the air quality. Then, the device was successfully tested for reliability by following the prescribed procedure from the Ministry of Environment, Korea. Also, cloud computing has been integrated into a web server for analyzing the data from the device to classify and visualize indoor air quality according to the standards from the Ministry. An application was developed to help in monitoring the air quality. Thus, approved personnel can monitor the air quality at any time and from anywhere, via either the web server or the application. The web server stores all data in the cloud to provide resources for further analysis of indoor air quality. In addition, the platform has been successfully implemented in Hanyang University of Korea to demonstrate its feasibility.
- 14 January 2020
- Published by Wiley in Journal of Sensors
- Vol. 2020, 1-14
Top Cited PapersOpen AccessDevelopment of an IoT-Based Indoor Air Quality Monitoring Platform
In this paper, an IoT-based indoor air quality monitoring platform, consisting of an air quality-sensing device called “Smart-Air” and a web server, is demonstrated. This platform relies on an IoT and a cloud computing technology to monitor indoor air quality in anywhere and anytime. Smart-Air has been developed based on the IoT technology to efficiently monitor the air quality and transmit the data to a web server via LTE in real time. The device is composed of a microcontroller, pollutant detection sensors, and LTE modem. In the research, the device was designed to measure a concentration of aerosol, VOC, CO, CO2, and temperature-humidity to monitor the air quality. Then, the device was successfully tested for reliability by following the prescribed procedure from the Ministry of Environment, Korea. Also, cloud computing has been integrated into a web server for analyzing the data from the device to classify and visualize indoor air quality according to the standards from the Ministry. An application was developed to help in monitoring the air quality. Thus, approved personnel can monitor the air quality at any time and from anywhere, via either the web server or the application. The web server stores all data in the cloud to provide resources for further analysis of indoor air quality. In addition, the platform has been successfully implemented in Hanyang University of Korea to demonstrate its feasibility.
- Open Access
Robust Construction Safety System (RCSS) for Collision Accidents Prevention on Construction Sites
A proximity warning system to detect the presence of a worker/workers and to warn heavy equipment operators is highly needed to prevent collision accidents at construction sites. In this paper, we developed a robust construction safety system (RCSS), which can activate warning devices and automatically halt heavy equipment, simultaneously, to prevent possible collision accidents. The proximity detection of this proposed system mainly relies on ultra-wideband (UWB) sensing technologies, which enable instantaneous and simultaneous alarms on (a) a worker’s personal safety (personal protection unit (PPU)) device and (b) hazard area device (zone alert unit (ZAU)). This system also communicates with electronic control sensors (ECSs) installed on the heavy equipment to stop its maneuvering. Moreover, the RCSS has been interfaced with a global positioning system communication unit (GCU) to acquire real-time information of construction site resources and warning events. This enables effective management of construction site resources using an online user interface. The performance and effectiveness of the RCSS have been validated at laboratory scale as well as at real field (construction site and steel factory). Conclusively, the RCSS can significantly enhance construction site safety by pro-actively preventing collision of a worker/workers with heavy equipment.
Open AccessRobust Construction Safety System (RCSS) for Collision Accidents Prevention on Construction Sites
A proximity warning system to detect the presence of a worker/workers and to warn heavy equipment operators is highly needed to prevent collision accidents at construction sites. In this paper, we developed a robust construction safety system (RCSS), which can activate warning devices and automatically halt heavy equipment, simultaneously, to prevent possible collision accidents. The proximity detection of this proposed system mainly relies on ultra-wideband (UWB) sensing technologies, which enable instantaneous and simultaneous alarms on (a) a worker’s personal safety (personal protection unit (PPU)) device and (b) hazard area device (zone alert unit (ZAU)). This system also communicates with electronic control sensors (ECSs) installed on the heavy equipment to stop its maneuvering. Moreover, the RCSS has been interfaced with a global positioning system communication unit (GCU) to acquire real-time information of construction site resources and warning events. This enables effective management of construction site resources using an online user interface. The performance and effectiveness of the RCSS have been validated at laboratory scale as well as at real field (construction site and steel factory). Conclusively, the RCSS can significantly enhance construction site safety by pro-actively preventing collision of a worker/workers with heavy equipment.
- Open Access
Development of a Cloud Computing-Based Pier Type Port Structure Stability Evaluation Platform Using Fiber Bragg Grating Sensors
Structure Health Monitoring is a topic of great interest in port structures due to the ageing of structures and the limitations of evaluating structures. This paper presents a cloud computing-based stability evaluation platform for a pier type port structure using Fiber Bragg Grating (FBG) sensors in a system consisting of a FBG strain sensor, FBG displacement gauge, FBG angle meter, gateway, and cloud computing-based web server. The sensors were installed on core components of the structure and measurements were taken to evaluate the structures. The measurement values were transmitted to the web server via the gateway to analyze and visualize them. All data were analyzed and visualized in the web server to evaluate the structure based on the safety evaluation index (SEI). The stability evaluation platform for pier type port structures involves the efficient monitoring of the structures which can be carried out easily anytime and anywhere by converging new technologies such as cloud computing and FBG sensors. In addition, the platform has been successfully implemented at “Maryang Harbor” situated in Maryang-Meyon of Korea to test its durability.
Open AccessDevelopment of a Cloud Computing-Based Pier Type Port Structure Stability Evaluation Platform Using Fiber Bragg Grating Sensors
Structure Health Monitoring is a topic of great interest in port structures due to the ageing of structures and the limitations of evaluating structures. This paper presents a cloud computing-based stability evaluation platform for a pier type port structure using Fiber Bragg Grating (FBG) sensors in a system consisting of a FBG strain sensor, FBG displacement gauge, FBG angle meter, gateway, and cloud computing-based web server. The sensors were installed on core components of the structure and measurements were taken to evaluate the structures. The measurement values were transmitted to the web server via the gateway to analyze and visualize them. All data were analyzed and visualized in the web server to evaluate the structure based on the safety evaluation index (SEI). The stability evaluation platform for pier type port structures involves the efficient monitoring of the structures which can be carried out easily anytime and anywhere by converging new technologies such as cloud computing and FBG sensors. In addition, the platform has been successfully implemented at “Maryang Harbor” situated in Maryang-Meyon of Korea to test its durability.
- Open Access
- 22 August 2017
- Published by MDPI AG in Sustainability
- Vol. 9 (8) , 1488
Proximity Warning and Excavator Control System for Prevention of Collision Accidents
Construction is a hazardous industry in which accidents occur frequently. Occupational accidents at construction sites are a serious public health issue in Korea. Construction site conditions often create dangerous situations by requiring workers and heavy equipment to work in close proximity to each other. In 2015, approximately 11% (46) of the 437 occupational fatalities in the construction industry in Korea resulted from workers colliding with objects or equipment. In this paper, we present a proximity warning system developed to address this issue and enhance safety at construction sites. The proposed technology functions in real time to alert workers and equipment operators of hazardous proximity situations. Also, when the radio frequency identification (RFID) sensor detects an approaching worker, the main board instantly shuts down the excavator for the prevention of accident. This system contains an RFID tag, RFID reader, alarm device, camera, a display device (the Around View Monitor), and excavator control technology. A field test demonstrated successful performance of the proposed system. It is widely applicable in small construction fields alongside excavators and other equipment because this system does not require additional communication infrastructure, such as servers.
- 22 August 2017
- Published by MDPI AG in Sustainability
- Vol. 9 (8) , 1488
Open AccessProximity Warning and Excavator Control System for Prevention of Collision Accidents
Construction is a hazardous industry in which accidents occur frequently. Occupational accidents at construction sites are a serious public health issue in Korea. Construction site conditions often create dangerous situations by requiring workers and heavy equipment to work in close proximity to each other. In 2015, approximately 11% (46) of the 437 occupational fatalities in the construction industry in Korea resulted from workers colliding with objects or equipment. In this paper, we present a proximity warning system developed to address this issue and enhance safety at construction sites. The proposed technology functions in real time to alert workers and equipment operators of hazardous proximity situations. Also, when the radio frequency identification (RFID) sensor detects an approaching worker, the main board instantly shuts down the excavator for the prevention of accident. This system contains an RFID tag, RFID reader, alarm device, camera, a display device (the Around View Monitor), and excavator control technology. A field test demonstrated successful performance of the proposed system. It is widely applicable in small construction fields alongside excavators and other equipment because this system does not require additional communication infrastructure, such as servers.
- Open Access
- 25 July 2017
- Published by MDPI AG in Sustainability
- Vol. 9 (8) , 1297
Trend Analysis of Construction Industrial Accidents in Korea from 2011 to 2015
The purpose of this study is to analyze the results of construction accidents occurred from 2011 to 2015 in Korea. The annual reports from the Ministry of Employment and Labor, Korea (MOEL), and the annual reports from the Statistics Korea were used for the analysis in this study. The gender, age, company size and accident types were chosen as a category to analyze the trend of various occupational accidents. In order to analyze the characteristics of construction accidents, incidence rates (IRs) and mortality rates (MRs) were calculated. Further, T-tests and ANOVA analysis were performed to discover the relationships among IRs, MRs, and chosen categories. Male workers’ IRs and MRs were significantly higher than those of female workers. Construction workers over 40 years of age suffered the most from occupational injuries. In terms of company size, as company size increases, both IRs and MRs tended to decrease. Occupational injuries caused by falls were higher than other accident types each year. This paper will be able to provide information on occupational accidents for establishing strategies to reduce the accident rate in construction sectors of Korea.
- 25 July 2017
- Published by MDPI AG in Sustainability
- Vol. 9 (8) , 1297
Open AccessTrend Analysis of Construction Industrial Accidents in Korea from 2011 to 2015
The purpose of this study is to analyze the results of construction accidents occurred from 2011 to 2015 in Korea. The annual reports from the Ministry of Employment and Labor, Korea (MOEL), and the annual reports from the Statistics Korea were used for the analysis in this study. The gender, age, company size and accident types were chosen as a category to analyze the trend of various occupational accidents. In order to analyze the characteristics of construction accidents, incidence rates (IRs) and mortality rates (MRs) were calculated. Further, T-tests and ANOVA analysis were performed to discover the relationships among IRs, MRs, and chosen categories. Male workers’ IRs and MRs were significantly higher than those of female workers. Construction workers over 40 years of age suffered the most from occupational injuries. In terms of company size, as company size increases, both IRs and MRs tended to decrease. Occupational injuries caused by falls were higher than other accident types each year. This paper will be able to provide information on occupational accidents for establishing strategies to reduce the accident rate in construction sectors of Korea.
- 1 December 2001
- Published by World Scientific Pub Co Pte Ltd in International Journal of Cooperative Information Systems
- Vol. 10 (04) , 509-530
DEADLINE ALLOCATION IN A TIME-CONSTRAINED WORKFLOW
Workflow management systems should efficiently manage workflow constraints such as time, resource, and cost during workflow executions. Especially, workflow time management is important in timely scheduling of workflow process execution, avoiding deadline violations, and improving the workflow throughput. Though there have been some studies on the dynamic deadline management in a workflow, the importance of the static deadline management has not been much addressed in the past. We first describe our workflow model considered in this paper. Then, we propose a static deadline allocation method that can facilitate an efficient workflow processing. The proposed method can achieve high workflow throughput by analyzing the interrelated workflow components. We also present various experimental results that show the usefulness and efficiency of the method.
- 1 December 2001
- Published by World Scientific Pub Co Pte Ltd in International Journal of Cooperative Information Systems
- Vol. 10 (04) , 509-530
DEADLINE ALLOCATION IN A TIME-CONSTRAINED WORKFLOW
Workflow management systems should efficiently manage workflow constraints such as time, resource, and cost during workflow executions. Especially, workflow time management is important in timely scheduling of workflow process execution, avoiding deadline violations, and improving the workflow throughput. Though there have been some studies on the dynamic deadline management in a workflow, the importance of the static deadline management has not been much addressed in the past. We first describe our workflow model considered in this paper. Then, we propose a static deadline allocation method that can facilitate an efficient workflow processing. The proposed method can achieve high workflow throughput by analyzing the interrelated workflow components. We also present various experimental results that show the usefulness and efficiency of the method.