Marcus Iberler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marcus Iberler has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
J. Jacoby
Goethe Universität Frankfurt, Max-von-Laue-Str. 1, 60438 Frankfurt am Main
3 shared publicationsA. Michel
Goethe Universität Frankfurt, Max-von-Laue-Str. 1, 60438 Frankfurt am Main
2 shared publicationsJoachim Jacoby
Institut fuer Angewandte Physik, Johann-Wolfgang-Goethe-Universitat, Frankfurt am Main, GERMANY
2 shared publications- B. F. Bohlender
Goethe Universität Frankfurt, Max-von-Laue-Str. 1, 60438 Frankfurt am Main
1 shared publication B.-J. Lee
Pohang Accelerator Laboratory 1 , Pohang, Kyungbuk 790-784, South Korea
1 shared publicationC. Benzing
Plasma Physics Group, Institute of Applied Physics, Goethe University , 60438 Frankfurt am Main, Germany
1 shared publication
Latest Publications
- Open Access
- 19 April 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (28) , 285203
Measurement of the free electron line density in a spherical theta-pinch plasma target by single wavelength interferometry
A single wavelength heterodyne interferometer has been set up to investigate the free electron density integrated axially along the line of sight (line density) in a theta-pinch plasma to determine its applicability as a plasma target for ion beam stripping. The maximal line density reached in this experiment was 3 . 57 ± 0 . 28 × 10 18 cm−2 at 80 Pa and 20 kV. The findings demonstrate the pulsed character of the line density and its increase by raising the load voltage and the working gas pressure. Additionally, the results were compared with spectroscopic free electron density estimations, which were carried out by H β -line broadening and peak separation. The time behavior of the line density indicates that its peak value is delayed by about 10 µs compared to the spectroscopic results. This effect is due to the formation of an extended, magnetically compressed plasma column in the vicinity of the current maximum, although the highest volumetric free electron density is reached near the current zero crossing. Since the line density is an essential parameter in describing the stripping capabilities of the plasma target, the interferometric diagnostic is superior to a spectroscopic diagnostic, because it directly provides integrated values along the line of sight. Furthermore, the measurements of the line density in this experiment partially show nonphysical negative values, which is due to gaseous effects and residual shot vibrations.
- 19 April 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (28) , 285203
Open AccessMeasurement of the free electron line density in a spherical theta-pinch plasma target by single wavelength interferometry
A single wavelength heterodyne interferometer has been set up to investigate the free electron density integrated axially along the line of sight (line density) in a theta-pinch plasma to determine its applicability as a plasma target for ion beam stripping. The maximal line density reached in this experiment was 3 . 57 ± 0 . 28 × 10 18 cm−2 at 80 Pa and 20 kV. The findings demonstrate the pulsed character of the line density and its increase by raising the load voltage and the working gas pressure. Additionally, the results were compared with spectroscopic free electron density estimations, which were carried out by H β -line broadening and peak separation. The time behavior of the line density indicates that its peak value is delayed by about 10 µs compared to the spectroscopic results. This effect is due to the formation of an extended, magnetically compressed plasma column in the vicinity of the current maximum, although the highest volumetric free electron density is reached near the current zero crossing. Since the line density is an essential parameter in describing the stripping capabilities of the plasma target, the interferometric diagnostic is superior to a spectroscopic diagnostic, because it directly provides integrated values along the line of sight. Furthermore, the measurements of the line density in this experiment partially show nonphysical negative values, which is due to gaseous effects and residual shot vibrations.
- Open Access
- 15 January 2020
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 23 (1) , 013501
Characterization of a plasma window as a membrane free transition between vacuum and high pressure
A plasma window (PW) is a device for separating two areas of different pressures while letting particle beams pass with little to no loss. It has been introduced by A. Hershcovitch [ J. Appl. Phys. 78, 5283 (1995)] In the course of this publication, the properties of a PW with apertures of 3.3 mm and 5.0 mm are presented. Especially the link between the pressure properties relevant for applications in accelerator systems and the underlying plasma properties depending on external parameters are presented. As working gas, a 98%Ar-2% mixture has been used due to the intense Stark broadening of the -line and the well-described Ar characteristics, enabling an accurate electron density and temperature analysis. At the low pressure side around some mbar, high-pressure values reached up to 750 mbar while operating with volume flows between 1 slm and 4 slm (standard liter per minute) and discharge currents ranging from 45 A to 60 A. The achieved ratios between high and low pressure with an active discharge range from 40 to 150. This is an improvement of a factor up to 12 over the performance of an ordinary differential pumping stage of the same geometry. Unique features of the presented PW include simultaneous plasma parameter determination and the absence of ceramic insulators between the cooling plates. Optical analysis reveals no significant damage or wear to the components after an operation time well over 10 h, whereas the cathode needle needs replacement after 5 h.- 15 January 2020
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 23 (1) , 013501
Open AccessCharacterization of a plasma window as a membrane free transition between vacuum and high pressure
A plasma window (PW) is a device for separating two areas of different pressures while letting particle beams pass with little to no loss. It has been introduced by A. Hershcovitch [ J. Appl. Phys. 78, 5283 (1995)] In the course of this publication, the properties of a PW with apertures of 3.3 mm and 5.0 mm are presented. Especially the link between the pressure properties relevant for applications in accelerator systems and the underlying plasma properties depending on external parameters are presented. As working gas, a 98%Ar-2% mixture has been used due to the intense Stark broadening of the -line and the well-described Ar characteristics, enabling an accurate electron density and temperature analysis. At the low pressure side around some mbar, high-pressure values reached up to 750 mbar while operating with volume flows between 1 slm and 4 slm (standard liter per minute) and discharge currents ranging from 45 A to 60 A. The achieved ratios between high and low pressure with an active discharge range from 40 to 150. This is an improvement of a factor up to 12 over the performance of an ordinary differential pumping stage of the same geometry. Unique features of the presented PW include simultaneous plasma parameter determination and the absence of ceramic insulators between the cooling plates. Optical analysis reveals no significant damage or wear to the components after an operation time well over 10 h, whereas the cathode needle needs replacement after 5 h. - 1 March 2019
- Published by AIP Publishing in Physics of Plasmas
- Vol. 26 (3) , 033512
Compression of an accelerated plasma cloud in a cone
This paper describes first results of a novel compression method for a plasma by acceleration into a glass cone. The plasma is generated by a pulsed-power-driven coaxial plasma accelerator, prefilled with 2% hydrogen in a helium mixture. The pulse forming network of the experiment has a total capacitance of 27 μF at a maximum voltage of 10 kV. The low inductance of 130 nH leads to an average frequency of about 86 kHz and high current rise rates in the range. Due to the high current of up to 150 kA, the Lorentz force accelerates the plasma depending on pressure and applied voltage to velocities in the order. After ejection, the plasma moves into several cone geometries, placed at the end of the electrodes. The conducted studies focus on the Stark-broadening of spectral lines to determine the electron density changes due to the compression. Because of the wide broadening at high electron densities, the well-known Hβ line broadening method is not eligible for cone compressed plasmas. Alternatively, the broadening of the Hα line and a copper line has been used. The achieved electron densities could be increased approximately two orders of magnitude from 1015 cm−3 without the cone to 1017–1018 cm−3 with cone compression.- 1 March 2019
- Published by AIP Publishing in Physics of Plasmas
- Vol. 26 (3) , 033512
Compression of an accelerated plasma cloud in a cone
This paper describes first results of a novel compression method for a plasma by acceleration into a glass cone. The plasma is generated by a pulsed-power-driven coaxial plasma accelerator, prefilled with 2% hydrogen in a helium mixture. The pulse forming network of the experiment has a total capacitance of 27 μF at a maximum voltage of 10 kV. The low inductance of 130 nH leads to an average frequency of about 86 kHz and high current rise rates in the range. Due to the high current of up to 150 kA, the Lorentz force accelerates the plasma depending on pressure and applied voltage to velocities in the order. After ejection, the plasma moves into several cone geometries, placed at the end of the electrodes. The conducted studies focus on the Stark-broadening of spectral lines to determine the electron density changes due to the compression. Because of the wide broadening at high electron densities, the well-known Hβ line broadening method is not eligible for cone compressed plasmas. Alternatively, the broadening of the Hα line and a copper line has been used. The achieved electron densities could be increased approximately two orders of magnitude from 1015 cm−3 without the cone to 1017–1018 cm−3 with cone compression.- Open Access
- 1 December 2013
- Published by AIP Publishing in Physics of Plasmas
- Vol. 20 (12) , 123510
Excimer emission from pulsed microhollow cathode discharges in xenon
Direct current (dc) microhollow cathode discharge (MHCD) is an intense source for excimer radiation in vacuum ultraviolet at a wavelength of 172 nm in a high pressure xenon (Xe) gas. The concentration of precursors for the excimer formation, i.e., excited and ionized gas atoms, increases significantly by applying high voltage pulse onto the dc MHCD over the pulse duration range from 20 to 100 ns. The intensity of the excimer emission for the voltage pulse of 20 ns duration exceeds that of the emission intensity obtained from the same MHCD operated only in the dc mode, by one order of magnitude. In addition, the emission intensity increases by one order of magnitude over the pulse duration range from 20 to 100 ns. It can be assumed that the emission intensity of the MHCD source increases as long as the duration of the high voltage pulse is shorter than the electron relaxation time. For the high voltage pulse of 100 ns duration, the emission intensity has been found to be further enhanced by a factor of three when the gas pressure is increased from 200 to 800 mbar.
- 1 December 2013
- Published by AIP Publishing in Physics of Plasmas
- Vol. 20 (12) , 123510
Open AccessExcimer emission from pulsed microhollow cathode discharges in xenon
Direct current (dc) microhollow cathode discharge (MHCD) is an intense source for excimer radiation in vacuum ultraviolet at a wavelength of 172 nm in a high pressure xenon (Xe) gas. The concentration of precursors for the excimer formation, i.e., excited and ionized gas atoms, increases significantly by applying high voltage pulse onto the dc MHCD over the pulse duration range from 20 to 100 ns. The intensity of the excimer emission for the voltage pulse of 20 ns duration exceeds that of the emission intensity obtained from the same MHCD operated only in the dc mode, by one order of magnitude. In addition, the emission intensity increases by one order of magnitude over the pulse duration range from 20 to 100 ns. It can be assumed that the emission intensity of the MHCD source increases as long as the duration of the high voltage pulse is shorter than the electron relaxation time. For the high voltage pulse of 100 ns duration, the emission intensity has been found to be further enhanced by a factor of three when the gas pressure is increased from 200 to 800 mbar.
- 21 April 2008
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 17 (2) , 025014
Density enhancement of an RF plasma in a magnetic quadrupole
- 21 April 2008
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 17 (2) , 025014
Density enhancement of an RF plasma in a magnetic quadrupole