Pakman Yiu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pakman Yiu has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Jhen-De You
3 shared publicationsJinn P. Chu
3 shared publications- Jinn P. Chu
Department of Materials Science and Technology National Taiwan University of Science and Technology Taipei Taiwan
3 shared publications - Bo-Zhang Lai
Department of Materials Science and Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
2 shared publications Agung Purniawan
1 shared publicationAlfreda Krisna Altama
1 shared publication
Latest Publications
- 16 December 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1050
Synergistic strengthening effect in a magnetron-sputtered amorphous/nanocrystalline Inconel-based medium entropy alloy coating
- 16 December 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1050
Synergistic strengthening effect in a magnetron-sputtered amorphous/nanocrystalline Inconel-based medium entropy alloy coating
- 28 January 2025
- Published by Elsevier in Applied Surface Science
- Vol. 690
A slippery and icephobic surface based on lubricant-infused metallic glass nanotube array
- 28 January 2025
- Published by Elsevier in Applied Surface Science
- Vol. 690
A slippery and icephobic surface based on lubricant-infused metallic glass nanotube array
- 9 October 2024
- Published by Elsevier in Materialia
- Vol. 38
A novel approach to fabricate Fe-based thin film metallic glass with commercial boron carbide and AISI M42 tool steel
- 9 October 2024
- Published by Elsevier in Materialia
- Vol. 38
A novel approach to fabricate Fe-based thin film metallic glass with commercial boron carbide and AISI M42 tool steel
- 3 June 2023
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 960
Fabrication of high aspect-ratio metallic nanotube array with highly-ordered periodicity using HiPIMS
- 3 June 2023
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 960
Fabrication of high aspect-ratio metallic nanotube array with highly-ordered periodicity using HiPIMS
- 1 July 2021
- Published by Elsevier in Applied Surface Science
- Vol. 555
Tunable hydrophilicity in a surface nano-textured stainless steel thin film deposited by DC magnetron sputtering
- 1 July 2021
- Published by Elsevier in Applied Surface Science
- Vol. 555
Tunable hydrophilicity in a surface nano-textured stainless steel thin film deposited by DC magnetron sputtering
- Open Access
- 24 July 2020
- Published by Springer Nature in Scientific Reports
- Vol. 10 (1) , 1-10
Metallic glass coating for improving diamond dicing performance
This is the first report on the coating of diamond dicing blades with metallic glass (MG) coating to reduce chipping when used to cut Si, SiC, sapphire, and patterned sapphire substrates (PSS). The low coefficient-of-friction (CoF) of Zr-based MG-coated dicing blades was shown to reduce the number and size of chips, regardless of the target substrate. Overall, SiC, sapphire and PSS were most affected by chipping, due to the fact that higher cutting forces were needed for the higher hardness of SiC, sapphire and PSS. Compared to the bare blade, the MG coating provided the following reductions in chipping area: Si (~ 23%), SiC (~ 36%), sapphire (~ 45%), and PSS (~ 33%). The proposed coating proved particularly effective in reducing chips of larger size (> 41 µm in chipping width), as indicated by an ~ 80% reduction when cutting sapphire. Small variations in kerf angle and depth demonstrate the durability of the coated blades, which would no doubt enhance consistency in dicing performance and extend the blade lifespan. Finite-element modeling revealed significant reductions in tensile stress and elastic–plastic deformation during dicing, thanks to a lower CoF.
- 24 July 2020
- Published by Springer Nature in Scientific Reports
- Vol. 10 (1) , 1-10
Open AccessMetallic glass coating for improving diamond dicing performance
This is the first report on the coating of diamond dicing blades with metallic glass (MG) coating to reduce chipping when used to cut Si, SiC, sapphire, and patterned sapphire substrates (PSS). The low coefficient-of-friction (CoF) of Zr-based MG-coated dicing blades was shown to reduce the number and size of chips, regardless of the target substrate. Overall, SiC, sapphire and PSS were most affected by chipping, due to the fact that higher cutting forces were needed for the higher hardness of SiC, sapphire and PSS. Compared to the bare blade, the MG coating provided the following reductions in chipping area: Si (~ 23%), SiC (~ 36%), sapphire (~ 45%), and PSS (~ 33%). The proposed coating proved particularly effective in reducing chips of larger size (> 41 µm in chipping width), as indicated by an ~ 80% reduction when cutting sapphire. Small variations in kerf angle and depth demonstrate the durability of the coated blades, which would no doubt enhance consistency in dicing performance and extend the blade lifespan. Finite-element modeling revealed significant reductions in tensile stress and elastic–plastic deformation during dicing, thanks to a lower CoF.
- 15 January 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (3) , 030901
Thin film metallic glasses: Properties, applications and future
In this article, we provide a perspective overview of the iconic properties, recent application-oriented research, and future commercialization opportunities of thin film metallic glasses (TFMGs). A brief review on the preparation and fundamental properties of TFMGs will be given first. TFMGs possess attractive properties such as corrosion resistance, extremely low roughness, and antibacterial characteristics, which give rise to various applications in biomedical devices, sensors, and tribology. Therefore, a number of our representative works will be reviewed to showcase the benefits of TFMGs over traditional materials and processing in these applications. In addition, new perspectives in the research and development of TFMGs and opportunities for commercialization will also be highlighted.
- 15 January 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (3) , 030901
Thin film metallic glasses: Properties, applications and future
In this article, we provide a perspective overview of the iconic properties, recent application-oriented research, and future commercialization opportunities of thin film metallic glasses (TFMGs). A brief review on the preparation and fundamental properties of TFMGs will be given first. TFMGs possess attractive properties such as corrosion resistance, extremely low roughness, and antibacterial characteristics, which give rise to various applications in biomedical devices, sensors, and tribology. Therefore, a number of our representative works will be reviewed to showcase the benefits of TFMGs over traditional materials and processing in these applications. In addition, new perspectives in the research and development of TFMGs and opportunities for commercialization will also be highlighted.