GXGuangshen Xu

Guangshen Xu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Guangshen Xu has a total of 21 co-authors. Here are the top co-authors by number of shared publications:

  • Chengzhi Li

    Group of Mechanical and Biomedical Engineering, Xi'an Key Laboratory of Modern Intelligent Textile Equipment, College of Mechanical & Electronic Engineering, Xi'an Polytechnic University, Xi'an, Shaanxi, China

    2 shared publications
  • Feilei Wang

    School of Mechanical and Electrical Engineering, Xi’an Polytechnic University, Xi’an 710048, China

    2 shared publications
  • Jiangtao Jia

    School of Mechanical and Electrical Engineering, Xi’an Polytechnic University, Xi’an 710048, China

    2 shared publications
  • Xuejing Liu

    School of Mechanical and Electrical Engineering, Xi’an Polytechnic University, Xi’an 710048, China

    2 shared publications
  • Zhouqiang Zhang

    School of Mechanical and Electrical Engineering, Xi’an Polytechnic University, Xi’an 710048, China

    2 shared publications
  • Bingheng Lu

    The State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an, China

    1 shared publication

Latest Publications

  • Preparation and lubrication properties of graphene oxide/polyethylene glycol/polyvinyl alcohol composite film

    by Hailin Lu, Chengzhi Li, Guangshen Xu

    In the rotating parts of large mechanical equipment, the existence of friction and wear will inevitably cause energy consumption and loss. Coating a layer of solid lubricating material on the surface of mechanical equipment is an effective means to reduce friction and wear. In this study, for the first time, a composite film with high mechanical and lubricating properties was prepared by hot-pressing the mixture of graphene oxide (GO), polyethylene glycol (PEG), and polyvinyl alcohol (PVA). Its structure and properties were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Raman spectroscopy (Raman), and thermogravimetric analysis (TGA). The lubrication and tribological properties of GO-PEG-PVA composite film and other single films under different lubrication conditions were analyzed. The lubrication characteristics of GO-PEG-PVA composite film under oil lubrication were discussed in detail. The results show that the surface coating with GO-PEG-PVA can ensure a lower friction coefficient, especially in the condition of oil lubrication, the friction coefficient is 82% lower than that without oil film. The hot pressing process ensures that the surface morphology will not produce large shear deformation. The lubrication mechanism and lubrication model were discussed in detail, and the concept of improving surface lubrication performance by co-lubrication was put forward.


  • Tribological properties of graphene oxide and polyethylene glycol composites under dry friction and oil lubrication conditions

    by Chengzhi Li, Guangshen Xu, Lisha Wang, Jianhui Li, Hailin Lu

    In the low speed and heavy load of large machinery rotation or sliding parts, the application of copper base ink plate is very extensive. In this study, the graphene oxide‐polyethylene glycol (GO‐PEG) thin films were prepared on the surface of steel plates by gradient heating, and we simulated the friction and wear state of the solid material when it was brought to the metal surface. And the Fourier transform infrared spectroscopy, X‐ray diffraction, X‐ray energy spectrum analysis, Raman spectroscopy (Raman), and thermogravimetric analysis were used to characterize the structure and properties. The tribological results show that the GO‐PEG composite film prepared by gradient temperature rise method has good lubrication effect. The addition of GO greatly enhances the mechanical properties of the composite films. Compared with the single GO film, the friction coefficient is reduced by 50% and the wear rate is reduced by 85%. The unique characteristics of PEG solved the accumulation phenomenon caused by the strong van der Waals force between GO, then the PEG adhered on GO surfaces caused good lubrication effect. At the same time, the composite film has a broad application prospect in the working environment with little oil and no oil.


  • Open Access

    Digital Twin-Driven Mating Performance Analysis for Precision Spool Valve

    by Wenbin Tang, Guangshen Xu, Shoujing Zhang, Shoufeng Jin, Runxiao Wang

    The precision spool valve is the core component of the electro-hydraulic servo control system, and its performance has an important influence on the flight control of aviation and aerospace products. The non-uniform surface topography error causes a non-uniform mating gap field inside the spool valve, which causes oil leakage and leads to deterioration of the spool valve performance. However, the current oil leakage calculation method only considers the influence of size errors, which is not comprehensive. Thus, how to characterize the mating behavior of the spool valve and its effect on oil leakage with consideration of surface topography errors is the key to evaluating the performance of the spool valve. This paper proposes a new way of analyzing the mating performance of precision spool valves, which considers the surface topography errors based on digital twin technology. Firstly, a general framework for the analysis of mating performance of precision spool valve based on a digital twin is proposed. Then, key technologies of assembly interface geometry modeling, matching behavior modeling and performance analysis are studied. Finally, a quantitative correlation between the mating parameters and the oil leakage of the precision spool valve is revealed. The method is tested on a practical case. This proposed method can provide theoretical support for the accurate prediction and evaluation of the mating performance of the precision spool valve.


  • Open Access

    Improved Carrier Frequency-Shifting Algorithm Based on 2-FFT for Phase Wrap Reduction

    by Zhouqiang Zhang, Feilei Wang, Guangshen Xu, Jiangtao Jia, Xuejing Liu, Yabin Cao

    The number of phase wraps that result from the carrier component can be completely eliminated or reduced by first applying a fast Fourier transform (FFT) to the image and then shifting the spectrum to the origin. However, because the spectrum can only be shifted by an integer number, the phase wraps of the carrier component cannot be completely reduced. In this paper, an improved carrier frequency-shifting algorithm based on 2-FFT for phase wrap reduction is proposed which allows the spectrum to be shifted by a rational number. Firstly, the phase wraps are reduced by the conventional FFT frequency shift method. Secondly, the wrapped phase with residual carrier components is filtered and magnified sequentially; the amplified phase is transformed into the frequency domain using an FFT, and then, the wrapped phase with the residual carrier components can be further reduced by shifting the spectrum by a rational number. Simulations and experiments were conducted to validate the efficiency of the proposed method.


  • Research on the knitting needle detection system of a hosiery machine based on machine vision

    by Zhouqiang Zhang, Sihao Bai, Guang-Shen Xu, Xuejing Liu, Feilei Wang, Jiangtao Jia, Zhi Feng

    Problems with knitting needles are one of the main causes of production loss of fabric. In order to detect problems with knitting needles quickly and accurately, this paper proposes a hosiery knitting needle detection system based on machine vision. Meanwhile, according to the working condition of real hosiery knitting needles, a simulated needle cylinder rotary platform is built. The system can detect knitting needle problems, and the needle causing the issue can be identified as the beginning of the fabric defect appears. The production losses caused by the bending and fracture of knitting needles are reduced at the source. In the image processing, the vertical projection algorithm is introduced in the system, and the defect of image binarization is improved. At the same time, the multi-classification support vector machine based on the decision tree is used to realize the image classification. The experimental results show that the classification accuracy of the two levels classifiers in the system can reach 100% and 98%, and the best time of system detection is 0.348 s.


  • Open Access

    Dimensional Variation Analysis for Rigid Part Assembly With an Improvement of Monte Carlo Simulation

    by Wenbin Tang, Guangshen Xu, Shoujing Zhang

    Dimensional variation has significant effect on the quality of product. Recently, Monte Carlo (MC) simulation is widely used in dimensional variation analysis, with high accuracy and adaptability, but there is the problem of low computational efficiency. Aiming to address this problem, an improvement of MC simulation is proposed through a two-phases solution. In the first phase, surrogate model is used to approximate the locating constraint equations for a 3D part, which reduces the nonlinear coupling between dimensional deviations and avoids large-scale solution of nonlinear equations in dimensional variation analysis on the condition of ensuring the accuracy. In the second phase, random samples used in MC simulation are replaced by low discrepancy sequences, which enable the samples to have better homogeneity and representativeness and reduce the number of samples required in the dimensional variation analysis. Finally, two examples are used to demonstrate the effectiveness of the method, and the results show that the two-phases solution has advantages both in the accuracy and efficiency.