Laura Annette Romero De León
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Laura Annette Romero De León has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Alan Bañuelos Frías
Maestría en Ciencias de la Ingeniería, Universidad Autónoma de Zacatecas, Zacatecas 98000, Mexico
1 shared publication - Carlos Alberto Garcia Rodriguez
Instituto Politécnico Nacional, Escuela Superior de Ingeniería Mecánica y Eléctrica, Mexico City, Mexico
1 shared publication - Claudia Yolanda Valero Luna
Maestría en Ciencias de la Ingeniería, Universidad Autónoma de Zacatecas, Zacatecas 98000, Mexico
1 shared publication - Elvia Valdez Valdez
Unidad Académica de Ciencias Químicas, Universidad Autónoma de Zacatecas, Zacatecas 98160, Mexico
1 shared publication - Jose Alfredo Jimenez Bernal
Instituto Politécnico Nacional (Méjico)
1 shared publication - Leo Alvarado Perea
Unidad Académica de Ciencias Químicas, Maestría en Ciencias de la Ingeniería and Posgrados en Ingeniería y Tecnología Aplicada, Universidad Autónoma de Zacatecas, Zacatecas 98160, Mexico
1 shared publication
Latest Publications
- Open Access
- 28 May 2026
- Published by Institute of Central Computation and Knowledge Inc. in Journal of Chemical Engineering and Renewable Fuels
- Vol. 2 (2) , 65-70
Phenol Photodegradation over Ni/MCM-41: Effect of the Ni Incorporation Method
This study explores the synthesis and application of Ni-based photocatalysts supported on MCM-41 and Al-MCM-41 for phenol degradation. Three preparation methods were evaluated and compared: Chemical Vapor Deposition (CVD), Incipient Wet Impregnation (IWI), and Template Ion Exchange (TIE). The influence of the Si/Al ratio of 5 and 60 on phenol photodegradation was also examined. The results showed that the Ni/MCM-41 photocatalyst prepared by CVD achieved the highest degradation efficiency (97.28%), while the TIE method proved to be the most versatile overall. Notably, the TIE method was the only synthesis method capable of exhibiting photocatalytic activity in phenol degradation on all supports at different Si/Al ratios, unlike the materials prepared by CVD and IWI, which failed to degrade phenol in the presence of aluminum. These results indicate the TIE method as a novel synthesis method for the development of mesoporous photocatalysts with high photocatalytic activity in the degradation of phenol with different Si/Al ratios in the MCM-41 structure.
- 28 May 2026
- Published by Institute of Central Computation and Knowledge Inc. in Journal of Chemical Engineering and Renewable Fuels
- Vol. 2 (2) , 65-70
Open AccessPhenol Photodegradation over Ni/MCM-41: Effect of the Ni Incorporation Method
This study explores the synthesis and application of Ni-based photocatalysts supported on MCM-41 and Al-MCM-41 for phenol degradation. Three preparation methods were evaluated and compared: Chemical Vapor Deposition (CVD), Incipient Wet Impregnation (IWI), and Template Ion Exchange (TIE). The influence of the Si/Al ratio of 5 and 60 on phenol photodegradation was also examined. The results showed that the Ni/MCM-41 photocatalyst prepared by CVD achieved the highest degradation efficiency (97.28%), while the TIE method proved to be the most versatile overall. Notably, the TIE method was the only synthesis method capable of exhibiting photocatalytic activity in phenol degradation on all supports at different Si/Al ratios, unlike the materials prepared by CVD and IWI, which failed to degrade phenol in the presence of aluminum. These results indicate the TIE method as a novel synthesis method for the development of mesoporous photocatalysts with high photocatalytic activity in the degradation of phenol with different Si/Al ratios in the MCM-41 structure.
- Open Access
- 6 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 6272-6281
Waste Heat Recovery System Applied to a High-Performance Video Card
This paper presents results given by a waste heat recovery (WHR) system applied to a highperformance video card, as well as average energy generated per hour according to emulation of computer graphics requirements demanded by the user while the card is working. A WHR system includes three phases: (1) waste heat collection, (2) energy conversion and (3) signal conditioning. The analysis of the WHR system is presented. The emulation of waste heat has been generated using electrical resistors as if they were the main components that generate waste heat, mainly the GPU (graphics processing unit), and DDR3 memories. This WHR system has considered the MSI-R4850 video card as a reference, operation temperature of which has an overall range between 60°C – 90°C. Thermoelectric generator modules (TEG) are based on the Seebeck effect, and the thermoelectric array used is an important part of the WHR system, which has been constructed based on the locations of the main components to convert waste heat into electrical power. The waste heat recovery process has two treatments: First, once the operating conditions, per GPU and DDR3 memories have been emulated, the energy recovered is measured per component and whole WHR system; the second one measures energy recovered considering the output signal conditioning of the WHR system, which was converted to 5V output through a DC-DC boost converter, while the input voltage operates within a range (0.9V – 5V). The energy recovered may be applied to low-power electronic devices, which is a contribution to energy efficiency.
- 6 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 6272-6281
Open AccessWaste Heat Recovery System Applied to a High-Performance Video Card
This paper presents results given by a waste heat recovery (WHR) system applied to a highperformance video card, as well as average energy generated per hour according to emulation of computer graphics requirements demanded by the user while the card is working. A WHR system includes three phases: (1) waste heat collection, (2) energy conversion and (3) signal conditioning. The analysis of the WHR system is presented. The emulation of waste heat has been generated using electrical resistors as if they were the main components that generate waste heat, mainly the GPU (graphics processing unit), and DDR3 memories. This WHR system has considered the MSI-R4850 video card as a reference, operation temperature of which has an overall range between 60°C – 90°C. Thermoelectric generator modules (TEG) are based on the Seebeck effect, and the thermoelectric array used is an important part of the WHR system, which has been constructed based on the locations of the main components to convert waste heat into electrical power. The waste heat recovery process has two treatments: First, once the operating conditions, per GPU and DDR3 memories have been emulated, the energy recovered is measured per component and whole WHR system; the second one measures energy recovered considering the output signal conditioning of the WHR system, which was converted to 5V output through a DC-DC boost converter, while the input voltage operates within a range (0.9V – 5V). The energy recovered may be applied to low-power electronic devices, which is a contribution to energy efficiency.