Michal Okoniewski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Michal Okoniewski has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
John Nielsen
Department of Electrical and Computer Engineering, University of Calgary, Calgary, AB T2N 1N4, Canada
3 shared publications- Leonid Belostotski
University of Calgary
3 shared publications - Arjuna Madanayake
Florida International University, Miami, USA
2 shared publications - Elise C. Fear
University of Calgary
2 shared publications I. Zine-El-Abidine
TRLabs., Calgary Univ., Alta., Canada
2 shared publicationsJ.G. McRory
University of Calgary
2 shared publications
Latest Publications
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (7) , 6686-6701
Limitations of MAMPs and Holland–Simpson Thin-Wire Models and a New Unified Wire Formalism in FDTD
Thin-wire subcell models enable the representation of wires with radii smaller than the grid resolution in the finite-difference time-domain (FDTD) method. While numerous formulations have been proposed, the differences between the numerical behavior of these models remain poorly understood. This work investigates two widely used models—the Modified Assigned Material Parameters (MAMPs) and Holland–Simpson formulations—by benchmarking their TMz plane wave scattering responses for wires of varying radii against analytical solutions. Numerical experiments show that MAMPs produces non-physical scattering for wires of small radius (i.e. r/Δx ≪ 1). The cause of artificial scattering is explained by showing that MAMPs erroneously enforces perfect conductors at locations where parameters are modified. Alternatively, Holland’s formalism requires a decreased time step compared to the standard Courant-Friedrichs-Levy (CFL) condition to maintain stability for large radius (i.e. r/Δx > 0.1). Even with this reduced time step, the model fails to produce accurate results. This failure is attributed to the Holland model’s limitation in representing higher-order scattering modes using a single stored current. To address these limitations, a novel thin-wire formalism is proposed for accurately modeling wires across all thickness regimes.
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (7) , 6686-6701
Limitations of MAMPs and Holland–Simpson Thin-Wire Models and a New Unified Wire Formalism in FDTD
Thin-wire subcell models enable the representation of wires with radii smaller than the grid resolution in the finite-difference time-domain (FDTD) method. While numerous formulations have been proposed, the differences between the numerical behavior of these models remain poorly understood. This work investigates two widely used models—the Modified Assigned Material Parameters (MAMPs) and Holland–Simpson formulations—by benchmarking their TMz plane wave scattering responses for wires of varying radii against analytical solutions. Numerical experiments show that MAMPs produces non-physical scattering for wires of small radius (i.e. r/Δx ≪ 1). The cause of artificial scattering is explained by showing that MAMPs erroneously enforces perfect conductors at locations where parameters are modified. Alternatively, Holland’s formalism requires a decreased time step compared to the standard Courant-Friedrichs-Levy (CFL) condition to maintain stability for large radius (i.e. r/Δx > 0.1). Even with this reduced time step, the model fails to produce accurate results. This failure is attributed to the Holland model’s limitation in representing higher-order scattering modes using a single stored current. To address these limitations, a novel thin-wire formalism is proposed for accurately modeling wires across all thickness regimes.
- Open Access
- 24 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 6 (3) , 894-901
Active Retrodirective Rotman Lens Antenna for Wide-Angle RCS Enhancement
This paper presents measurement results and analysis of an innovative active retrodirective Rotman lens antenna architecture, designed to enhance the radar cross-section (RCS) for backscattering applications. Unlike conventional passive retrodirective systems, our design integrates custom-designed reflection amplifiers to significantly boost backscattered signal gain while maintaining low DC power consumption. A novel biasing technique enables independent phase and gain control of the amplifiers, ensuring a uniform array response and reducing DC power consumption by approximately 30%. Experimental monostatic RCS measurements at 5.15 GHz with a linearly polarized incident wave demonstrate a uniform RCS response over a ±40° scan angle. The integration of reflection amplifiers enhances backscattering, allowing the lens to maintain a consistent −0.5 dB RCS across the entire scan angle, which is 9 dB higher than the average RCS of a metal plate with the same effective aperture. The compact design (approximately $6\lambda \times 6\lambda $ ) and ultra-low power consumption (approximately 0.19 mW) make this system well-suited for low-power radar applications, such as mm-wave automotive radar sensors. These results confirm the feasibility of active-loaded phase conjugating systems for high-performance backscattering applications.
- 24 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 6 (3) , 894-901
Open AccessActive Retrodirective Rotman Lens Antenna for Wide-Angle RCS Enhancement
This paper presents measurement results and analysis of an innovative active retrodirective Rotman lens antenna architecture, designed to enhance the radar cross-section (RCS) for backscattering applications. Unlike conventional passive retrodirective systems, our design integrates custom-designed reflection amplifiers to significantly boost backscattered signal gain while maintaining low DC power consumption. A novel biasing technique enables independent phase and gain control of the amplifiers, ensuring a uniform array response and reducing DC power consumption by approximately 30%. Experimental monostatic RCS measurements at 5.15 GHz with a linearly polarized incident wave demonstrate a uniform RCS response over a ±40° scan angle. The integration of reflection amplifiers enhances backscattering, allowing the lens to maintain a consistent −0.5 dB RCS across the entire scan angle, which is 9 dB higher than the average RCS of a metal plate with the same effective aperture. The compact design (approximately $6\lambda \times 6\lambda $ ) and ultra-low power consumption (approximately 0.19 mW) make this system well-suited for low-power radar applications, such as mm-wave automotive radar sensors. These results confirm the feasibility of active-loaded phase conjugating systems for high-performance backscattering applications.
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (8) , 5471-5481
A Demonstration of a Wideband Low-Complexity Multibeam Analog Beamforming Network
This work proposes using a sparse factorization of the multibeam delay Vandermonde matrix (DVM) for reducing the complexity of multibeam analog beamformers. The example of a proof-of-concept sparse-factorized DVM theoretically requires only 70 of unit true time delays (TTDs) to implement four beams with eight antennas, compared with the 252 unit TTDs required in conventional implementations. The number of TTDs was further reduced to 65 by simplifying the signal-flow graph (SFG). A proof-of-concept integrated multibeam radio-frequency (RF) beamformer is discussed. It utilizes TTDs to realize four simultaneous beams to cover a spatial area of 0∘ to 60∘. To demonstrate the concept, a prototype of the proposed four-beam beamformer was fabricated in a 22-nm fully depleted silicon-on-insulator (FDSOI) CMOS process. This proof-of-concept prototype operates from 1.6 to 5.6 GHz, occupies a chip area of 0.37 mm2, uses 58 current-mode unit TTDs, 27 current-mode adders, and consumes 3.7 mW/channel of dc power. This simplified approach to realizing multibeam networks has the potential to enhance the implementation efficiency in analog and hybrid beamforming systems, including multi-input multi-output (MIMO) arrays, 5G and 6G arrays, and SATCOM arrays.
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (8) , 5471-5481
A Demonstration of a Wideband Low-Complexity Multibeam Analog Beamforming Network
This work proposes using a sparse factorization of the multibeam delay Vandermonde matrix (DVM) for reducing the complexity of multibeam analog beamformers. The example of a proof-of-concept sparse-factorized DVM theoretically requires only 70 of unit true time delays (TTDs) to implement four beams with eight antennas, compared with the 252 unit TTDs required in conventional implementations. The number of TTDs was further reduced to 65 by simplifying the signal-flow graph (SFG). A proof-of-concept integrated multibeam radio-frequency (RF) beamformer is discussed. It utilizes TTDs to realize four simultaneous beams to cover a spatial area of 0∘ to 60∘. To demonstrate the concept, a prototype of the proposed four-beam beamformer was fabricated in a 22-nm fully depleted silicon-on-insulator (FDSOI) CMOS process. This proof-of-concept prototype operates from 1.6 to 5.6 GHz, occupies a chip area of 0.37 mm2, uses 58 current-mode unit TTDs, 27 current-mode adders, and consumes 3.7 mW/channel of dc power. This simplified approach to realizing multibeam networks has the potential to enhance the implementation efficiency in analog and hybrid beamforming systems, including multi-input multi-output (MIMO) arrays, 5G and 6G arrays, and SATCOM arrays.
- Top Cited Papers
- 5 October 2023
- Published by Springer Nature in Nature Reviews Methods Primers
- Vol. 3 (1) , 1-19
Finite-difference time-domain methods
- 5 October 2023
- Published by Springer Nature in Nature Reviews Methods Primers
- Vol. 3 (1) , 1-19
Top Cited PapersFinite-difference time-domain methods
- 24 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (8) , 5090-5094
Framework for the Cosimulation of Antenna Arrays and Receivers
This paper presents a framework for co-simulating receiving antenna arrays and receivers using circuit simulators. This framework is based on a recently introduced 2M-port electrical model of an M-element antenna array with M physically accessible ports and M “free-space” ports. Based on this framework, we describe analytical and simulator-based approaches to determining receiving-array performance metrics, such as isotropic noise response, beam-equivalent system and receiver noise temperatures, and noise-matching efficiency.
- 24 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (8) , 5090-5094
Framework for the Cosimulation of Antenna Arrays and Receivers
This paper presents a framework for co-simulating receiving antenna arrays and receivers using circuit simulators. This framework is based on a recently introduced 2M-port electrical model of an M-element antenna array with M physically accessible ports and M “free-space” ports. Based on this framework, we describe analytical and simulator-based approaches to determining receiving-array performance metrics, such as isotropic noise response, beam-equivalent system and receiver noise temperatures, and noise-matching efficiency.
- 23 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (7) , 2911-2919
An Uncoated RF Heating Applicator With Reduced Environmental Sensitivity Using Two Coaxial Discontinuities
The proposed design pursues an applicator that can survive deployment into deep hydrocarbon deposits. To ensure mechanical robustness, the design must be supported by a contiguous metal pipe, and to this end, the applicator uses a single-bare conductor transmission line excited bidirectionally with two coaxial discontinuities. These two discontinuities create a virtual impedance boundary through field superposition, where, ideally, the virtual boundary is a termination for a tuning stub formed in the surrounding material. As the material around the applicator changes, so does the impedance of the stub, engendering a degree of self-tuning behavior. The applicator concept was validated at 2.45 GHz, where the double discontinuity gave an S₁₁ of less than -10 dB in three different material cases and the measured electric field magnitude around the applicator was similar to simulation.
- 23 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (7) , 2911-2919
An Uncoated RF Heating Applicator With Reduced Environmental Sensitivity Using Two Coaxial Discontinuities
The proposed design pursues an applicator that can survive deployment into deep hydrocarbon deposits. To ensure mechanical robustness, the design must be supported by a contiguous metal pipe, and to this end, the applicator uses a single-bare conductor transmission line excited bidirectionally with two coaxial discontinuities. These two discontinuities create a virtual impedance boundary through field superposition, where, ideally, the virtual boundary is a termination for a tuning stub formed in the surrounding material. As the material around the applicator changes, so does the impedance of the stub, engendering a degree of self-tuning behavior. The applicator concept was validated at 2.45 GHz, where the double discontinuity gave an S₁₁ of less than -10 dB in three different material cases and the measured electric field magnitude around the applicator was similar to simulation.
- 24 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (7) , 5387-5394
Antenna-Array Network Model
An antenna can be modeled as a two-port network using S-parameters. However, having individual antenna S-parameters is not sufficient for modeling an array of antennas as antennas exhibit mutual coupling. This article proposes a network model to represent an antenna array with mutual coupling. Using the proposed model, an N-element antenna array is modeled as a combination of two-port networks representing each element and an N-port network representing mutual coupling. Two techniques to calculate mutual coupling S-parameters are presented: a primary method using numerical solutions and an approximate method using approximate expressions. The proposed model was validated using four monopole arrays having different interelement spacings, the number of elements, and nonidentical antennas.
- 24 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (7) , 5387-5394
Antenna-Array Network Model
An antenna can be modeled as a two-port network using S-parameters. However, having individual antenna S-parameters is not sufficient for modeling an array of antennas as antennas exhibit mutual coupling. This article proposes a network model to represent an antenna array with mutual coupling. Using the proposed model, an N-element antenna array is modeled as a combination of two-port networks representing each element and an N-port network representing mutual coupling. Two techniques to calculate mutual coupling S-parameters are presented: a primary method using numerical solutions and an approximate method using approximate expressions. The proposed model was validated using four monopole arrays having different interelement spacings, the number of elements, and nonidentical antennas.
- 12 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (6) , 2409-2418
A Class E/Fodd Power Oscillator Incorporating a Distributed Active Transformer
A power combined high-efficiency oscillator is proposed using a hybrid class E and class F tuning, where the odd harmonics are shorted: the class E/Fodd. The oscillator is achieved by adding a high-pass feedback network to a class E/Fodd amplifier, where the output's odd harmonics are used to construct the required square-like wave at the input. Furthermore, two class E/Fodd oscillators can be power combined using a distributed active transformer, where magnetic coupling to the high-pass feedback network can be realized using a third transformer winding. Two power combined class E/Fodd oscillators designed using this method have an oscillation frequency of 10.1 MHz, a total output power of 324 W and dc-to-RF conversion efficiency of 75%.
- 12 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (6) , 2409-2418
A Class E/Fodd Power Oscillator Incorporating a Distributed Active Transformer
A power combined high-efficiency oscillator is proposed using a hybrid class E and class F tuning, where the odd harmonics are shorted: the class E/Fodd. The oscillator is achieved by adding a high-pass feedback network to a class E/Fodd amplifier, where the output's odd harmonics are used to construct the required square-like wave at the input. Furthermore, two class E/Fodd oscillators can be power combined using a distributed active transformer, where magnetic coupling to the high-pass feedback network can be realized using a third transformer winding. Two power combined class E/Fodd oscillators designed using this method have an oscillation frequency of 10.1 MHz, a total output power of 324 W and dc-to-RF conversion efficiency of 75%.
- 25 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (1) , 405-413
Active Phase-Conjugating Rotman Lens With Reflection Amplifiers for Backscattering Enhancement
Active retrodirective antenna arrays find a variety of use in applications involving wireless communication and sensing systems. This article presents a novel active version of the phase-conjugating Rotman lens with negative conductance amplifiers for applications requiring high retrodirective gain or modulation capability. Implementation challenges and limitations of extending the existing passive retrodirective Rotman lens into this enhanced active mode are described. In order to retain system stability when electrically connecting multiple potentially unstable devices, a narrowband negative conductance is designed specifically for augmenting onto the lens. The measurements demonstrate an eleven-antenna element lens with a phase-conjugating gain of 19.2-25.4 dB across a ±32° scanning range at 5.15 GHz when loaded with nine amplifiers tuned to ≈6.5-dB reflection gain. The entire system consumes only 2.4 mW of power. The circuits implemented are easily scalable to higher frequency applications. Therefore, this proof-of-concept phase-conjugating system is a step toward designing very high-gain retrodirective arrays for mm-wave applications.
- 25 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (1) , 405-413
Active Phase-Conjugating Rotman Lens With Reflection Amplifiers for Backscattering Enhancement
Active retrodirective antenna arrays find a variety of use in applications involving wireless communication and sensing systems. This article presents a novel active version of the phase-conjugating Rotman lens with negative conductance amplifiers for applications requiring high retrodirective gain or modulation capability. Implementation challenges and limitations of extending the existing passive retrodirective Rotman lens into this enhanced active mode are described. In order to retain system stability when electrically connecting multiple potentially unstable devices, a narrowband negative conductance is designed specifically for augmenting onto the lens. The measurements demonstrate an eleven-antenna element lens with a phase-conjugating gain of 19.2-25.4 dB across a ±32° scanning range at 5.15 GHz when loaded with nine amplifiers tuned to ≈6.5-dB reflection gain. The entire system consumes only 2.4 mW of power. The circuits implemented are easily scalable to higher frequency applications. Therefore, this proof-of-concept phase-conjugating system is a step toward designing very high-gain retrodirective arrays for mm-wave applications.
- Open Access
- 15 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 17 (3) , 442-445
On Accuracy of Perfect Electric Conductor Implementation in Lebedev FDTD
The Lebedev grid is an alternative to Yee grid where, because the discretized fields lie at the same location in space, there is no need for further field interpolations when modeling anisotropic materials. In this letter, we focus on accurately implementing perfect electric conductors with planar interfaces, as well as 90° and 270° corners. Simulations are provided to demonstrate the overall improvements and also the second-order accuracy of the proposed methods.
- 15 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 17 (3) , 442-445
Open AccessOn Accuracy of Perfect Electric Conductor Implementation in Lebedev FDTD
The Lebedev grid is an alternative to Yee grid where, because the discretized fields lie at the same location in space, there is no need for further field interpolations when modeling anisotropic materials. In this letter, we focus on accurately implementing perfect electric conductors with planar interfaces, as well as 90° and 270° corners. Simulations are provided to demonstrate the overall improvements and also the second-order accuracy of the proposed methods.