Rajesh Kumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Rajesh Kumar has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Sujit Karmakar
Department of Mechanical Engineering, National Institute of Technology Durgapur, Durgapur, India
2 shared publications - Abhishek Arora1 shared publication
Amardip Ghosh
1 shared publicationC Danani
Institute for Plasma Research, Gandhinagar 382428, India
1 shared publication- Deepak Sharma
Institute for Plasma Research
1 shared publication Goutam Khankari
Simulator Training Centre, MTPS, DVC
1 shared publication
Latest Publications
- 4 November 2022
- Published by Taylor & Francis
- p. 157-173
Multi-parametric optimization of a convective type waste heat recovery system
Waste heat recovery is an important criterion that helps the industries to optimize their overall production process. Since steel production activities consume a large amount of energy and the flue gases generated are exhausted out through a stack chimney, the heat energy associated with flue gases can be significantly recovered to preheat the combustion air using a recuperator. The recuperator under consideration in the present chapter is operational at Continuous Strip Production Mill of ArcelorMittal/Nippon Steel India Ltd. at Hazira, Surat, India. In an attempt to maximize the waste heat recovery, the current work deals with the optimization of geometric and operational parameters to reduce the overallpressure drop of the combustion air and improve the effectiveness of the recuperator. To take into account the effects of curvature of tubes, a 3D model of the recuperator is further simulated in ANSYS Fluent. Finally, a comparative analysis is done for three different recuperator configurations. The final results are presented in the form of optimum ranges and values of geometric and flow parameters indicating that a recuperator with curved tubes configuration offers maximum waste heat recovery. An optimum tube diameter of 38.67 mm is suggested for the present recuperator configuration.
- 4 November 2022
- Published by Taylor & Francis
- p. 157-173
Multi-parametric optimization of a convective type waste heat recovery system
Waste heat recovery is an important criterion that helps the industries to optimize their overall production process. Since steel production activities consume a large amount of energy and the flue gases generated are exhausted out through a stack chimney, the heat energy associated with flue gases can be significantly recovered to preheat the combustion air using a recuperator. The recuperator under consideration in the present chapter is operational at Continuous Strip Production Mill of ArcelorMittal/Nippon Steel India Ltd. at Hazira, Surat, India. In an attempt to maximize the waste heat recovery, the current work deals with the optimization of geometric and operational parameters to reduce the overallpressure drop of the combustion air and improve the effectiveness of the recuperator. To take into account the effects of curvature of tubes, a 3D model of the recuperator is further simulated in ANSYS Fluent. Finally, a comparative analysis is done for three different recuperator configurations. The final results are presented in the form of optimum ranges and values of geometric and flow parameters indicating that a recuperator with curved tubes configuration offers maximum waste heat recovery. An optimum tube diameter of 38.67 mm is suggested for the present recuperator configuration.
- 30 September 2022
- Published by Wiley
- p. 295-325
Optimization of PV Electrolyzer for Hydrogen Production
- 30 September 2022
- Published by Wiley
- p. 295-325
Optimization of PV Electrolyzer for Hydrogen Production
- 23 September 2022
- Published by Taylor & Francis
- p. 77-81
Mode transition in a strut-based parallel-fuel-injection scramjet-engine
Transition from SCRAM to RAM mode combustion in DLR’s strut-based parallel-fuel-injector DMSC using vitiated air as oxidizer and gaseous hydrogen as fuel is investigated numerically using the commercially available Ansys-Fluent software. A two-dimensional density-based implicit-solver using the k-ε turbulence model is used for steady state simulations. Species transport with finite rate/eddy dissipation chemistry and turbulent combustion model is used to investigate the combustion process. Fuel flow rate is increased in steps while holding airflow rate constant. Resultant increase in heat release rates is seen to raise the pressure downstream of the strut with a concomitant rearrangement of the location and steepness of the shock waves eventually resulting in a drastic transition from SCRAM to RAM mode operation.
- 23 September 2022
- Published by Taylor & Francis
- p. 77-81
Mode transition in a strut-based parallel-fuel-injection scramjet-engine
Transition from SCRAM to RAM mode combustion in DLR’s strut-based parallel-fuel-injector DMSC using vitiated air as oxidizer and gaseous hydrogen as fuel is investigated numerically using the commercially available Ansys-Fluent software. A two-dimensional density-based implicit-solver using the k-ε turbulence model is used for steady state simulations. Species transport with finite rate/eddy dissipation chemistry and turbulent combustion model is used to investigate the combustion process. Fuel flow rate is increased in steps while holding airflow rate constant. Resultant increase in heat release rates is seen to raise the pressure downstream of the strut with a concomitant rearrangement of the location and steepness of the shock waves eventually resulting in a drastic transition from SCRAM to RAM mode operation.
- 19 May 2022
- Published by IOP Publishing in Plasma Science and Technology
- Vol. 24 (6) , 065601
Neutronic analysis of Indian helium-cooled solid breeder tritium breeding module for testing in ITER
India has proposed the helium-cooled solid breeder blanket concept as a tritium breeding module to be tested in ITER. The module has lithium titanate for tritium breeding and beryllium for neutron multiplication. Beryllium also enhances tritium breeding. A design for the module is prepared for detailed analysis. Neutronic analysis is performed to assess the tritium breeding rate, neutron distribution, and heat distribution in the module. The tritium production distribution in submodules is evaluated to support the tritium transport analysis. The tritium breeding density in the radial direction of the module is also assessed for further optimization of the design. The heat deposition profile of the entire module is generated to support the heat removal circuit design. The estimated neutron spectrum in the radial direction also provides a more in-depth picture of the nuclear interactions inside the material zones. The total tritium produced in the HCSB module is around 13.87 mg per full day of operation of ITER, considering the 400 s ON time and 1400 s dwell time. The estimated nuclear heat load on the entire module is around 474 kW, which will be removed by the high-pressure helium cooling circuit. The heat deposition in the test blanket model (TBM) is huge (around 9 GJ) for an entire day of operation of ITER, which demonstrates the scale of power that can be produced through a fusion reactor blanket. As per the Brayton cycle, it is equivalent to 3.6 GJ of electrical energy. In terms of power production, this would be around 1655 MWh annually. The evaluation is carried out using the MCNP5 Monte Carlo radiation transport code and FEDNL 2.1 nuclear cross section data. The HCSB TBM neutronic performance demonstrates the tritium production capability and high heat deposition.
- 19 May 2022
- Published by IOP Publishing in Plasma Science and Technology
- Vol. 24 (6) , 065601
Neutronic analysis of Indian helium-cooled solid breeder tritium breeding module for testing in ITER
India has proposed the helium-cooled solid breeder blanket concept as a tritium breeding module to be tested in ITER. The module has lithium titanate for tritium breeding and beryllium for neutron multiplication. Beryllium also enhances tritium breeding. A design for the module is prepared for detailed analysis. Neutronic analysis is performed to assess the tritium breeding rate, neutron distribution, and heat distribution in the module. The tritium production distribution in submodules is evaluated to support the tritium transport analysis. The tritium breeding density in the radial direction of the module is also assessed for further optimization of the design. The heat deposition profile of the entire module is generated to support the heat removal circuit design. The estimated neutron spectrum in the radial direction also provides a more in-depth picture of the nuclear interactions inside the material zones. The total tritium produced in the HCSB module is around 13.87 mg per full day of operation of ITER, considering the 400 s ON time and 1400 s dwell time. The estimated nuclear heat load on the entire module is around 474 kW, which will be removed by the high-pressure helium cooling circuit. The heat deposition in the test blanket model (TBM) is huge (around 9 GJ) for an entire day of operation of ITER, which demonstrates the scale of power that can be produced through a fusion reactor blanket. As per the Brayton cycle, it is equivalent to 3.6 GJ of electrical energy. In terms of power production, this would be around 1655 MWh annually. The evaluation is carried out using the MCNP5 Monte Carlo radiation transport code and FEDNL 2.1 nuclear cross section data. The HCSB TBM neutronic performance demonstrates the tritium production capability and high heat deposition.
- 18 October 2020
- Published by Springer Nature
- p. 1185-1198
Thermodynamic Analysis of a Combined Power and Cooling System Integrated with CO2 Capture Unit of a 500 MWe SupC Coal-Fired Power Plant
- 18 October 2020
- Published by Springer Nature
- p. 1185-1198
Thermodynamic Analysis of a Combined Power and Cooling System Integrated with CO2 Capture Unit of a 500 MWe SupC Coal-Fired Power Plant
- 17 January 2020
- Published by Springer Nature
- p. 907-919
Thermodynamic Analysis of a 500-MWe Subcritical Coal-Fired Thermal Power Plant with Solar-Aided Post-Combustion CO2 Capture
- 17 January 2020
- Published by Springer Nature
- p. 907-919
Thermodynamic Analysis of a 500-MWe Subcritical Coal-Fired Thermal Power Plant with Solar-Aided Post-Combustion CO2 Capture