Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Duc Ahn Nguyen has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Nghiên cứu hoạt tính sinh học và khả năng ứng dụng chiết xuất lá trầu không (Piper Betle L.) trong lớp phủ chống bám bẩn sinh học

    by Đức Anh Nguyễn, Nhật Linh Cao, Thị Mỹ Hiệp Lê, Văn Kiên Đồng, Thị Hồng Xanh Nguyễn

    Bài báo này trình bày kết quả nghiên cứu khả năng sử dụng chiết xuất lá trầu không (Piper betle L.) với vai trò là một loại phụ gia kháng khuẩn cho lớp phủ chống bám bẩn sinh học thân thiện với môi trường. Hoạt chất sinh học của chiết xuất được xác định qua hàm lượng phenolic tổng số. Kết quả cho thấy hàm lượng phenolic tổng số trong chiết xuất đạt 260,3 mg GAE/g chất khô. Hoạt tính kháng khuẩn của chiết xuất được đánh giá bằng phương pháp khuếch tán trên đĩa thạch. Độc tính sinh học được đánh giá trên ấu trùng Artemia salina. Kết quả cho thấy, chiết xuất lá trầu không có hoạt tính kháng khuẩn cao đối với quần xã vi sinh vật biển với đường kính vòng kháng khuẩn đạt 35,1 ± 0,5 mm. Độc tính sinh học của chiết xuất đối với ấu trùng Artemia salina ở mức độ trung bình (LC50 > 100 µg/mL). Kết quả thử nghiệm tự nhiên trong môi trường nước biển trong điều kiện tĩnh cho thấy, việc bổ sung chiết xuất lá trầu không vào thành phần lớp phủ trên cơ sở acrylic copolymer giúp tăng đáng kể hiệu quả chống bám bẩn sinh học của lớp phủ. Tuy nhiên, ở điều kiện thử nghiệm động (thử nghiệm quay) hiệu quả chống bám bẩn của lớp phủ chứa chiết xuất thấp hơn đáng kể so với lớp phủ có sử dụng Cu2O

  • Open Access

    Application of Piper betle Leaf Extract as a Bioactive Additive in Eco-Friendly Antifouling Coatings

    by Nguyen Duc Anh, Cao Nhat Linh, Le Thi My Hiep, Dong Van Kien

    The present study aimed to evaluate the antifouling efficacy of Piper betle leaf extracts as a bioactive additive for eco-friendly antifouling coatings. The composition of P. betle extract was determined and analyzed. Phytochemical analysis revealed that the ethanol extract of P. betle contained phenolics, tannins, proteins, carbohydrates, and flavonoids, with total phenolic content reaching 260.3 mg GAE/g dry weight and flavonoid content reaching 52.56 mg QE/g dry weight. The antibacterial test results showed that the ethanol extract of P. betle exhibited maximum antibacterial efficacy against E. coli, B. subtilis, S. aureus, and marine bacteria, with inhibition zone diameters of 28.7 ± 0.5, 27.0 ± 1.6, 22.1 ± 0.6, and 35.1 ± 0.5 mm, respectively. Based on the laboratory test results, the ethanol extract of P. betle was chosen to be added to coatings as an antifouling additive. The content of the extract was 0.5, 1.0, and 1.5 wt.%. A field test conducted in tropical seawater (at Nha Trang Bay) demonstrated that incorporating 1 wt.% of P. betle extract into an acrylic copolymer-based coating significantly enhanced its antifouling performance. After nine months of immersion in seawater, this sample maintained an antifouling efficiency of 74%. These findings highlight the potential of P. betle extract as a sustainable alternative to conventional antifouling agents in marine coatings.

  • Open Access

    Electrodeposition of Cu-Reinforced Polyaniline Coating for Protection of AH36 Steel in Natural Seawater

    by Nguyen Van Chi, Le Hong Quan, Cao Nhat Linh, Nong Quoc Quang, Nguyen Duc Anh, Dong Van Kien, Nguyen Van Hoa

    The marine environment is highly corrosive for mild and low alloy steels. This study aimed to enhance the corrosion resistance of the AH36 steel in a saline medium by coating it with a copper particles reinforced polyaniline (PANI) layer. PANI and Cu particles were grown on the steel surface by electrodepositing methods. Firstly, PANI was electropolymerized in the presence of oxalic acid, followed by the electrodeposition of Cu particles at different deposition times. The coating showed a well-distribution of Cu particles in the polymer matrix and excellent adhesion. Furthermore, the Cu particles and PANI-coated steels exhibited corrosion resistance significantly in the saline medium compared to the bare substrate and pristine PANI-coated samples. The improved corrosion protection of a Cu@PANI coating on the AH36 steel could contribute to forming a physical barrier by filling Cu particles on the PANI pores.


  • Open Access

    Progress in Sensors for Monitoring Reinforcement Corrosion in Reinforced Concrete Structures—A Review

    by Dmitry Shevtsov, Nhat Linh Cao, Van Chi Nguyen, Quoc Quang Nong, Hong Quan Le, Duc Anh Nguyen, Ilya Zartsyn, Oleg Kozaderov

    Non-destructive monitoring methods and continuous monitoring systems based on them are crucial elements of modern systems for the management and maintenance of assets which include reinforced concrete structures. The purpose of our study was to summarise the data on the most common sensors and systems for the non-destructive monitoring of reinforced concrete structures developed over the past 20 years. We considered systems based on electrochemical (potentiometry, methods related to polarisation) and physical (electromagnetic and ultrasonic waves, piezoelectric effect, thermography) examination methods. Special focus is devoted to the existing sensors and the results obtained using these sensors, as well as the advantages and disadvantages of their setups or other equipment used. The review considers earlier approaches and available commercial products, as well as relatively new sensors which are currently being tested.


  • Mechanical and tribological properties of antifriction peek-based composites formed by hot pressing and FDM

    by D. G. Buslovich, D. A. Nguyen, Yu. V. Dontsov, L. A. Kornienko, S. V. Panin

    With the aim of development antifriction polymer polyetheretherketone based composites for friction units some mechanical and tribological properties of three-component PEEK-based composites loaded with two type of solid lubricant particles (PTFE and MoS2) and fabricated by two methods (hot pressing and fused deposition modeling) have been investigated. It was found that in comparison with unfilled PEEK the wear rate can be decreased by 39 times under testing over steel counterpart, and by 15 times over a ceramic one for a composite obtained by hot pressing, while for 3D-printed composite it was equal to 11 and by 2 times, respectively. It was shown that despite the decrease in the mechanical and tribological properties of the composite obtained by the FDM method in comparison with the hot-pressed one, it was possible to significantly increase the wear resistance compared to neat PEEK. It is recommended to use a composite “PEEK+10 wt % PTFE+0.5 wt % MoS2” for fabricating complex shape products for friction units by the FDM method.

  • Open Access

    Effect of Various Type of Nanoparticles on Mechanical and Tribological Properties of Wear-Resistant PEEK + PTFE-Based Composites

    by Sergey V. Panin, Duc A. Nguyen, Dmitry G. Buslovich, Vladislav O. Alexenko, Aleksander V. Pervikov, Lyudmila A. Kornienko, Filippo Berto

    The mechanical and tribological properties of polyetheretherketone (PEEK)- and PEEK + PTFE (polytetrafluoroethylene)-based composites loaded with and four types of nanoparticles (carbonaceous, metallic, bimetal oxide, and ceramic) under metal- and ceramic-polymer tribological contact conditions were investigated. It was found that loading with the nanofillers in a small content (0.3 wt.%) enabled improvement of the elastic modulus of the PEEK-based composites by 10–15%. In the metal–polymer tribological contact, wear resistance of all nanocomposites was increased by 1.5–2.3 times. In the ceramic-polymer tribological contact, loading PEEK with metal nanoparticles caused the intensification of oxidation processes, the microabrasive counterpart wear, and a multiple increase in the wear rate of the composites. The three component “PEEK/10PTFE/0.3 nanofillers” composites provided an increase in wear resistance, up to 22 times, for the metal–polymer tribological contact and up to 12 times for the ceramic-polymer one (with a slight decrease in the mechanical properties) compared to that of neat PEEK. In all cases, this was achieved by the polymer transfer film formation and adherence on the counterparts. The various effects of the four types of nanoparticles on wear resistance were determined by their ability to fix the PTFE-containing transfer film on the counterpart surfaces.


  • Open Access

    Material Design Methodology for Optimized Wear-Resistant Thermoplastic–Matrix Composites Based on Polyetheretherketone and Polyphenylene Sulfide

    by Sergey V. Panin, Boris A. Lyukshin, Svetlana A. Bochkareva, Lyudmila A. Kornienko, Duc Ahn Nguyen, Le Thi My Hiep, Iliya L. Panov, Nataliya Y. Grishaeva

    The main goal of this paper is to design and justify optimized compositions of thermoplastic–matrix wear-resistant composites based on polyetheretherketone (PEEK) and polyphenylene sulfide (PPS). Their mechanical and tribological properties have been specified in the form of bilateral and unilateral limits. For this purpose, a material design methodology has been developed. It has enabled to determine the optimal degrees of filling of the PEEK- and PPS-based composites with carbon microfibers and polytetrafluoroethylene particles. According to the results of tribological tests, the PEEK-based composites have been less damaged on the metal counterpart than the PPS-based samples having the same degree of filling. Most likely, this was due to more uniform permolecular structure and greater elasticity of the matrix. The described methodology is versatile and can be used to design various composites. Its implementation does not impose any limits on the specified properties of the material matrix or the reinforcing inclusions. The initial data on the operational characteristics can be obtained experimentally or numerically. The methodology enables to design the high-strength wear-resistant composites which are able to efficiently operate both in metal–polymer and ceramic–polymer friction units.


  • Open Access

    Enhancement of mechanical and tribotechnical properties of polymer composites with thermoplastic UHMWPE and PEEK matrices by loading carbon nanofibers/nanotubes

    by S. V. Panin, L. A. Kornienko, Nguyen Duc Anh, V. O. Alexenko, L. R. Ivanova

    For comparative evaluation of the influence of carbon nanofiber/nanotube loading in two different thermoplastic matrices (UHMWPE and PEEK), some mechanical and tribotechnical properties of the nanocomposites have been studied. It is shown that mechanical properties of nanocomposites change in various manners with increasing loading of carbon nanofibers and nanotubes. Herewith, the wear resistance of the “UHMWPE+1 wt% CNF and PEEK + 1 wt% CNF” composites under dry sliding friction is doubled. It is shown that, regardless of various effects on permolecular structure formation, the studied nanofillers enhance the wear resistance of the composites in a similar manner. A comparative analysis of the influence of nanofillers on the modification of mechanical and tribotechnical properties of UHMWPE- and PEEK-based matrices is made.