Jean-Pierre Pereira-Ramos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jean-Pierre Pereira-Ramos has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Rita Baddour-Hadjean
Institut de Chimie et des Matériaux Paris Est (ICMPE) UMR 7182 CNRS-Université Paris-Est Creteil 2 rue Henri Dunant 94320 Thiais France
7 shared publications - Barbara Laïk
Univ Paris Est Creteil, CNRS, ICMPE, UMR 7182, 2 rue Henri Dunant, 94320 Thiais, France
3 shared publications Ankush Bhatia
Institut de Chimie et des Matériaux Paris-Est (ICMPE) UMR 7182 CNRS-Université Paris-Est Creteil 2 rue Henri Dunant 94320 Thiais France
2 shared publications- Nicolas Emery
Institut de Chimie et des Matériaux Paris Est, ICMPE/GESMAT, UMR 7182 CNRS-Université Paris Est Créteil, CNRS 2 rue Henri Dunant, 94320 Thiais, France
2 shared publications R. Baddour-Hadjean
2 shared publications- Ankush Bhatia
Institut de Chimie et des Matériaux Paris-Est, UMR 7182 CNRS-UPEC, Thiais, France
1 shared publication
Latest Publications
- 29 June 2022
- Published by Elsevier in Journal of Power Sources
- Vol. 542
Kinetic insights into LixNi0.67N (1.67 ≤ x ≤ 2.17), a quasi “zero-strain” negative electrode material for Li-ion battery
- 29 June 2022
- Published by Elsevier in Journal of Power Sources
- Vol. 542
Kinetic insights into LixNi0.67N (1.67 ≤ x ≤ 2.17), a quasi “zero-strain” negative electrode material for Li-ion battery
- 6 April 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 9 (23) , 13496-13505
Detailed redox mechanism and self-discharge diagnostic of 4.9 V LiMn 1.5 Ni 0.5 O 4 spinel cathode revealed by Raman spectroscopy
Lithium-ion batteries are commonly used for electrical energy storage in portable devices and are promising systems for large-scale energy storage. However, their application is still limited due to electrode degradation and stability issues. To enhance the fundamental understanding of electrode degradation, we report on the Raman spectroscopic characterization of the promising 5 V spinel LiMn1.5Ni0.5O4 (LMNO) composite cathode. The Raman spectral variations displayed during the charge–discharge cycle in the 3.5–4.9 V vs. Li+/Li potential range are shown to be strongly associated with the change in the transition metals valence states. A careful electrochemical and spectroscopic analysis allows identifying specific descriptors of the Ni2+/Ni3+/Ni4+ species in the Raman spectra and providing their relative ratio during the redox process. This combined approach demonstrates the efficiency of Raman spectroscopy to determine the state of charge (SOC) of the LMNO cathode, paving the way for a fast and reliable measure of the self-discharge phenomenon in the spinel electrode.
- 6 April 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 9 (23) , 13496-13505
Detailed redox mechanism and self-discharge diagnostic of 4.9 V LiMn 1.5 Ni 0.5 O 4 spinel cathode revealed by Raman spectroscopy
Lithium-ion batteries are commonly used for electrical energy storage in portable devices and are promising systems for large-scale energy storage. However, their application is still limited due to electrode degradation and stability issues. To enhance the fundamental understanding of electrode degradation, we report on the Raman spectroscopic characterization of the promising 5 V spinel LiMn1.5Ni0.5O4 (LMNO) composite cathode. The Raman spectral variations displayed during the charge–discharge cycle in the 3.5–4.9 V vs. Li+/Li potential range are shown to be strongly associated with the change in the transition metals valence states. A careful electrochemical and spectroscopic analysis allows identifying specific descriptors of the Ni2+/Ni3+/Ni4+ species in the Raman spectra and providing their relative ratio during the redox process. This combined approach demonstrates the efficiency of Raman spectroscopy to determine the state of charge (SOC) of the LMNO cathode, paving the way for a fast and reliable measure of the self-discharge phenomenon in the spinel electrode.
- 9 May 2020
- Published by Wiley in ChemElectroChem
- Vol. 7 (16) , 3420-3428
An Exploratory Investigation of Spinel LiMn1.5Ni0.5O4 as Cathode Material for Potassium‐Ion Battery
The emerging interest in K‐ion batteries (KIBs) increases the importance of cathodes with high working voltage in this system. The LiMn1.5Ni0.5O4 spinel is a promising alternative for the next generation of high voltage Li‐ion positive electrodes and its delithiated structure could be of interest for KIBs. In this work, Li ions are extracted from LiMn1.5Ni0.5O4 by a first electrochemical oxidation. The electroformed λ‐Mn0.75Ni0.25O2 spinel phase is shown to convert into layered K0.5Mn0.75Ni0.25O2 (KMNO) at 20 °C along the first discharge in K cell. Then, 0.3 K+/KMNO (90 mAh g−1) are reversibly exchanged during the subsequent cycle. Superior electrochemical performance are reported for KMNO as compared to K0.5MnO2 (KMO): a higher working voltage vs. K+/K (3.10 V vs. 2.79 V), enhanced rate capability and better cycling stability (70 mAh g−1 after 60 cycles at C/20 for KMNO vs. 40 mAh g−1 for KMO). The contribution of the Ni redox system is revealed as a reason for these improved performances.
- 9 May 2020
- Published by Wiley in ChemElectroChem
- Vol. 7 (16) , 3420-3428
An Exploratory Investigation of Spinel LiMn1.5Ni0.5O4 as Cathode Material for Potassium‐Ion Battery
The emerging interest in K‐ion batteries (KIBs) increases the importance of cathodes with high working voltage in this system. The LiMn1.5Ni0.5O4 spinel is a promising alternative for the next generation of high voltage Li‐ion positive electrodes and its delithiated structure could be of interest for KIBs. In this work, Li ions are extracted from LiMn1.5Ni0.5O4 by a first electrochemical oxidation. The electroformed λ‐Mn0.75Ni0.25O2 spinel phase is shown to convert into layered K0.5Mn0.75Ni0.25O2 (KMNO) at 20 °C along the first discharge in K cell. Then, 0.3 K+/KMNO (90 mAh g−1) are reversibly exchanged during the subsequent cycle. Superior electrochemical performance are reported for KMNO as compared to K0.5MnO2 (KMO): a higher working voltage vs. K+/K (3.10 V vs. 2.79 V), enhanced rate capability and better cycling stability (70 mAh g−1 after 60 cycles at C/20 for KMNO vs. 40 mAh g−1 for KMO). The contribution of the Ni redox system is revealed as a reason for these improved performances.
- 1 May 2020
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2020-01 (2) , 240
Origin of the Enhanced Electrochemical Performance of Ball-Milled g’-V2O5 Puckered Layer Polymorph for Na-Ion Battery: A Kinetic and Structural Study
Sodium-ion batteries (SIBs) have entailed an increasing interest as attractive alternatives to Lithium-ion batteries (LIBs) because of the lower cost, high abundance and large worldwide availability of Na sources, especially in the context of large-scale storage applications. The major challenge in SIBs is to propose good Na-host materials with optimal electrochemical properties and most SIBs cathode materials are either imitating or duplicating existing lithium analogues. Recently, our group reported the potential interest of various V2O5 polymorphs towards Na insertion with promising performance revealed for the γ’-V2O5 polymorph in terms of specific capacities and cycle life [1]. γ’-V2O5 is prepared by chemical oxidation of the γ-LiV2O5 bronze synthesized through a carbothermal route. Topotactic lithium removal is observed, that keeps the original puckered layer stacking of the bronze precursor and leads to micrometric γ’-V2O5 platelets. γ’-V2O5 is able to accommodate nearly 1 Na ion leading to an attractive capacity of 145 mAh g-1, surprisingly at the same working potential than Li insertion (3.3 V vs Na+/Na). However, this cathode material suffers from a poor first charge efficiency that never exceeds 50% at moderate rate. A detailed structural study has established the discharge-charge mechanism for 0 We show in this work that an appropriate ball-milling protocol can be successfully applied to enhance the electrochemical performance of : a significant increase in the first cycle efficiency (from 50 to 90%) is achieved (Fig. 1). The rate capability of the charge capacity is greatly improved with for instance more than 100 mAh g-1 available at 1C for the ball milled material vs. only 40 mAh g-1 for as prepared γ’-V2O5. While the structure of γ’-V2O5 is not altered upon ball milling, a lower particle size combined with a decrease by a factor 3 of the crystallite size is observed as well as a modification of the discharge-charge profile, quite different from that of as-prepared γ’-V2O5 (Fig. 1). Such results suggest peculiar structural mechanism and kinetic features upon sodiation of the ball-milled material. The present work aims at understanding the origin of the enhanced electrochemical properties of ball-milled γ’-V2O5 as cathode material for NIB. A detailed structural study as a function of sodium uptake will enlighten the typical electrochemical profile of ball-milled γ’-V2O5. Special attention will also be paid to the crucial kinetic parameters of electrochemical Na insertion reaction in ball-milled γ’-V2O5 as a function of x in γ-NaxV2O5 (0 ≤ x < 1), using ac impedance measurements. A comparative study of structure modifications (phase diagram) and kinetic parameters (double-layer capacity, charge transfer kinetics, Na diffusion, electrode impedance) for the balled-milled and un-milled materials allows explaining the promoting impact of crystallite size on electrochemical sodium insertion properties of γ’-V2O5. References 1- M. Safrany Renard, N. Emery, R. Baddour-Hadjean, J. P. Pereira-Ramos, γ’-V2O5: A new high voltage cathode material for sodium-ion battery, Electrochim. Acta 252 (2017) 4-11. 2- M. Safrany Renard, R. Baddour-Hadjean, J. P. Pereira-Ramos, Kinetic insight into the electrochemical sodium insertion-extraction mechanism of the puckered γ’-V2O5 polymorph, Electrochim. Acta 322 (2019) 134670 Figure 1. First discharge-charge galvanostatic cycle of g’-V2O5. (a) as-prepared powder; (b) ball-milled powder. C/10 rate. Electrolyte 1M NaClO4/PC, 2% Vol. FEC Figure 1
- 1 May 2020
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2020-01 (2) , 240
Origin of the Enhanced Electrochemical Performance of Ball-Milled g’-V2O5 Puckered Layer Polymorph for Na-Ion Battery: A Kinetic and Structural Study
Sodium-ion batteries (SIBs) have entailed an increasing interest as attractive alternatives to Lithium-ion batteries (LIBs) because of the lower cost, high abundance and large worldwide availability of Na sources, especially in the context of large-scale storage applications. The major challenge in SIBs is to propose good Na-host materials with optimal electrochemical properties and most SIBs cathode materials are either imitating or duplicating existing lithium analogues. Recently, our group reported the potential interest of various V2O5 polymorphs towards Na insertion with promising performance revealed for the γ’-V2O5 polymorph in terms of specific capacities and cycle life [1]. γ’-V2O5 is prepared by chemical oxidation of the γ-LiV2O5 bronze synthesized through a carbothermal route. Topotactic lithium removal is observed, that keeps the original puckered layer stacking of the bronze precursor and leads to micrometric γ’-V2O5 platelets. γ’-V2O5 is able to accommodate nearly 1 Na ion leading to an attractive capacity of 145 mAh g-1, surprisingly at the same working potential than Li insertion (3.3 V vs Na+/Na). However, this cathode material suffers from a poor first charge efficiency that never exceeds 50% at moderate rate. A detailed structural study has established the discharge-charge mechanism for 0 We show in this work that an appropriate ball-milling protocol can be successfully applied to enhance the electrochemical performance of : a significant increase in the first cycle efficiency (from 50 to 90%) is achieved (Fig. 1). The rate capability of the charge capacity is greatly improved with for instance more than 100 mAh g-1 available at 1C for the ball milled material vs. only 40 mAh g-1 for as prepared γ’-V2O5. While the structure of γ’-V2O5 is not altered upon ball milling, a lower particle size combined with a decrease by a factor 3 of the crystallite size is observed as well as a modification of the discharge-charge profile, quite different from that of as-prepared γ’-V2O5 (Fig. 1). Such results suggest peculiar structural mechanism and kinetic features upon sodiation of the ball-milled material. The present work aims at understanding the origin of the enhanced electrochemical properties of ball-milled γ’-V2O5 as cathode material for NIB. A detailed structural study as a function of sodium uptake will enlighten the typical electrochemical profile of ball-milled γ’-V2O5. Special attention will also be paid to the crucial kinetic parameters of electrochemical Na insertion reaction in ball-milled γ’-V2O5 as a function of x in γ-NaxV2O5 (0 ≤ x < 1), using ac impedance measurements. A comparative study of structure modifications (phase diagram) and kinetic parameters (double-layer capacity, charge transfer kinetics, Na diffusion, electrode impedance) for the balled-milled and un-milled materials allows explaining the promoting impact of crystallite size on electrochemical sodium insertion properties of γ’-V2O5. References 1- M. Safrany Renard, N. Emery, R. Baddour-Hadjean, J. P. Pereira-Ramos, γ’-V2O5: A new high voltage cathode material for sodium-ion battery, Electrochim. Acta 252 (2017) 4-11. 2- M. Safrany Renard, R. Baddour-Hadjean, J. P. Pereira-Ramos, Kinetic insight into the electrochemical sodium insertion-extraction mechanism of the puckered γ’-V2O5 polymorph, Electrochim. Acta 322 (2019) 134670 Figure 1. First discharge-charge galvanostatic cycle of g’-V2O5. (a) as-prepared powder; (b) ball-milled powder. C/10 rate. Electrolyte 1M NaClO4/PC, 2% Vol. FEC Figure 1
- 1 May 2020
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2020-01 (2) , 206
Electrochemical Behavior and Structural Change of Spinel-LiMn2-XNixO4 (x = 0, 0.5) Cathode in Potassium Cells
On the recent research front for the next generation secondary batteries beyond Li, potassium insertion into graphite in non-aqueous cells has brought new insights into the electrochemical K+ intercalation behavior and introduced advantageous benefits from potassium. Since potassium resources are much abundant and the standard potential of K+/K is 0.13 V below that of Li+/Li, potassium-ion batteries can be regarded as an appealing alternative to LIBs to realize high voltage systems with low cost. The crucial issue is the development of cathode materials able to accommodate the large K-ion without displaying detrimental structural changes toward cycle life and rate capability performance. The 4.7 V LiMn1.5Ni0.5O4 spinel is already a promising cathode for the next generation of high voltage LIBs, and its host structure, λ-Mn0.75Ni0.25O2, could be of great interest for K-ion batteries. Here, we investigate for the first time the potassium insertion properties into electrochemically prepared λ-MnO2 (λ-MO) and λ-Mn0.75Ni0.25O2 (λ-MNO) spinels. Lithium ions in LiMn2O4 and LiMn1.5Ni0.5O4 samples are electrochemically extracted in lithium containing electrolyte solution, forming λ-Mn1- xNixO2 (x = 0, 0.25) by first oxidation process. Potassium ions are then inserted into the lithium extracted spinel phases. From structural analysis by X-ray diffraction and Raman spectroscopy, it is found that the original λ-Mn0.75Ni0.25O2 spinel phase converts into a layered phase, K~0.5Mn0.75Ni0.25O2. Then, K~0.5Mn0.75Ni0.25O2 can deliver a high reversible capacity of 90 mAh g-1 at C/20 in the 2 V- 4.6 V vs K+/K voltage range with 78% retention for 60 cycles at C/20 (Fig. 1). Promising rate performance are also evidenced with an initial capacity of 60 mAh g-1 at C/5 (Fig. 1), and 65% retention after 300 cycles at C/5. The origin of the attractive electrochemical performances of λ-MNO is investigated by XRD , Raman and EDS experiments after discharge and charge cycles. These results open the possibility of using inexpensive and high-capacity Mn-based active materials for potassium-ion batteries. Figure 1. Electrochemical properties of λ-Mn0.75Ni0.25O2 in a potassium cell. 1M KF6 /EC:PC 1:1 electrolyte, 2% vol. FEC. Voltage window 4.5 V- 2 V. Figure 1
- 1 May 2020
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2020-01 (2) , 206
Electrochemical Behavior and Structural Change of Spinel-LiMn2-XNixO4 (x = 0, 0.5) Cathode in Potassium Cells
On the recent research front for the next generation secondary batteries beyond Li, potassium insertion into graphite in non-aqueous cells has brought new insights into the electrochemical K+ intercalation behavior and introduced advantageous benefits from potassium. Since potassium resources are much abundant and the standard potential of K+/K is 0.13 V below that of Li+/Li, potassium-ion batteries can be regarded as an appealing alternative to LIBs to realize high voltage systems with low cost. The crucial issue is the development of cathode materials able to accommodate the large K-ion without displaying detrimental structural changes toward cycle life and rate capability performance. The 4.7 V LiMn1.5Ni0.5O4 spinel is already a promising cathode for the next generation of high voltage LIBs, and its host structure, λ-Mn0.75Ni0.25O2, could be of great interest for K-ion batteries. Here, we investigate for the first time the potassium insertion properties into electrochemically prepared λ-MnO2 (λ-MO) and λ-Mn0.75Ni0.25O2 (λ-MNO) spinels. Lithium ions in LiMn2O4 and LiMn1.5Ni0.5O4 samples are electrochemically extracted in lithium containing electrolyte solution, forming λ-Mn1- xNixO2 (x = 0, 0.25) by first oxidation process. Potassium ions are then inserted into the lithium extracted spinel phases. From structural analysis by X-ray diffraction and Raman spectroscopy, it is found that the original λ-Mn0.75Ni0.25O2 spinel phase converts into a layered phase, K~0.5Mn0.75Ni0.25O2. Then, K~0.5Mn0.75Ni0.25O2 can deliver a high reversible capacity of 90 mAh g-1 at C/20 in the 2 V- 4.6 V vs K+/K voltage range with 78% retention for 60 cycles at C/20 (Fig. 1). Promising rate performance are also evidenced with an initial capacity of 60 mAh g-1 at C/5 (Fig. 1), and 65% retention after 300 cycles at C/5. The origin of the attractive electrochemical performances of λ-MNO is investigated by XRD , Raman and EDS experiments after discharge and charge cycles. These results open the possibility of using inexpensive and high-capacity Mn-based active materials for potassium-ion batteries. Figure 1. Electrochemical properties of λ-Mn0.75Ni0.25O2 in a potassium cell. 1M KF6 /EC:PC 1:1 electrolyte, 2% vol. FEC. Voltage window 4.5 V- 2 V. Figure 1
- 4 December 2019
- Published by Wiley in ChemSusChem
- Vol. 13 (4) , 724-731
Mechanistic Investigation of a Hybrid Zn/V2O5 Rechargeable Battery with a Binary Li+/Zn2+ Aqueous Electrolyte
Low‐cost, easily processable, and environmentally friendly rechargeable aqueous zinc batteries have great potential for large‐scale energy storage, which justifies their receiving extensive attention in recent years. An original concept based on the use of a binary Li+/Zn2+ aqueous electrolyte is described herein for the case of the Zn/V2O5 system. In this hybrid, the positive side involves mainly the Li+ insertion/deinsertion reaction of V2O5, whereas the negative electrode operates according to zinc dissolution–deposition cycles. The Zn//3 mol L−1 Li2SO4–4 mol L−1 ZnSO4///V2O5 cell worked in the narrow voltage range of 1.6–0.8 V with capacities of approximately 136–125 mA h g−1 at rates of C/20–C/5, respectively. At 1 C, the capacity of 80 mA h g−1 was outstandingly stable for more than 300 cycles with a capacity retention of 100 %. A detailed structural study by XRD and Raman spectroscopy allowed the peculiar response of the V2O5 layered host lattice on discharge–charge and cycling to be unraveled. Strong similarities with the well‐known structural changes reported in nonaqueous lithiated electrolytes were highlighted, although the emergence of the usual distorted δ‐LiV2O5 phase was not detected on discharge to 0.8 V. The pristine host structure was restored and maintained during cycling with mitigated structural changes leading to high capacity retention. The present electrochemical and structural findings reveal a reaction mechanism mainly based on Li+ intercalation, but co‐intercalation of a few Zn2+ ions between the oxide layers cannot be completely dismissed. The presence of zinc cations between the oxide layers is thought to relieve the structural stress induced in V2O5 under operation, and this resulted in a limited volume expansion of 4 %. This fundamental investigation of a reaction mechanism operating in an environmentally friendly aqueous medium has not been reported before.
- 4 December 2019
- Published by Wiley in ChemSusChem
- Vol. 13 (4) , 724-731
Mechanistic Investigation of a Hybrid Zn/V2O5 Rechargeable Battery with a Binary Li+/Zn2+ Aqueous Electrolyte
Low‐cost, easily processable, and environmentally friendly rechargeable aqueous zinc batteries have great potential for large‐scale energy storage, which justifies their receiving extensive attention in recent years. An original concept based on the use of a binary Li+/Zn2+ aqueous electrolyte is described herein for the case of the Zn/V2O5 system. In this hybrid, the positive side involves mainly the Li+ insertion/deinsertion reaction of V2O5, whereas the negative electrode operates according to zinc dissolution–deposition cycles. The Zn//3 mol L−1 Li2SO4–4 mol L−1 ZnSO4///V2O5 cell worked in the narrow voltage range of 1.6–0.8 V with capacities of approximately 136–125 mA h g−1 at rates of C/20–C/5, respectively. At 1 C, the capacity of 80 mA h g−1 was outstandingly stable for more than 300 cycles with a capacity retention of 100 %. A detailed structural study by XRD and Raman spectroscopy allowed the peculiar response of the V2O5 layered host lattice on discharge–charge and cycling to be unraveled. Strong similarities with the well‐known structural changes reported in nonaqueous lithiated electrolytes were highlighted, although the emergence of the usual distorted δ‐LiV2O5 phase was not detected on discharge to 0.8 V. The pristine host structure was restored and maintained during cycling with mitigated structural changes leading to high capacity retention. The present electrochemical and structural findings reveal a reaction mechanism mainly based on Li+ intercalation, but co‐intercalation of a few Zn2+ ions between the oxide layers cannot be completely dismissed. The presence of zinc cations between the oxide layers is thought to relieve the structural stress induced in V2O5 under operation, and this resulted in a limited volume expansion of 4 %. This fundamental investigation of a reaction mechanism operating in an environmentally friendly aqueous medium has not been reported before.
- 1 June 2015
- Published by Elsevier in Electrochimica Acta
- Vol. 167, 20-24
Optimization of cycling properties of the layered lithium cobalt nitride Li2.20Co0.40N as negative electrode material for Li-ion batteries
- 1 June 2015
- Published by Elsevier in Electrochimica Acta
- Vol. 167, 20-24
Optimization of cycling properties of the layered lithium cobalt nitride Li2.20Co0.40N as negative electrode material for Li-ion batteries
- 1 March 2015
- Published by Elsevier in Electrochimica Acta
- Vol. 157, 218-224
Cycling strategies for optimizing silicon nanowires performance as negative electrode for lithium battery
- 1 March 2015
- Published by Elsevier in Electrochimica Acta
- Vol. 157, 218-224
Cycling strategies for optimizing silicon nanowires performance as negative electrode for lithium battery
- 1 February 2011
- Published by Elsevier in Journal of Power Sources
- Vol. 196 (3) , 1392-1398
Modification of the LixV2O5 phase diagram by incorporation of chromium oxide
- 1 February 2011
- Published by Elsevier in Journal of Power Sources
- Vol. 196 (3) , 1392-1398
Modification of the LixV2O5 phase diagram by incorporation of chromium oxide
- 18 July 2010
- Published by Springer Nature in Ionics
- Vol. 16 (7) , 577-580
Lithiated c-V2O5 thin-film as positive electrode for rocking-chair solid-state lithium microbattery
- 18 July 2010
- Published by Springer Nature in Ionics
- Vol. 16 (7) , 577-580
Lithiated c-V2O5 thin-film as positive electrode for rocking-chair solid-state lithium microbattery