Fabián Andrés Tapias Hernandez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Fabián Andrés Tapias Hernandez has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Andres F. Ortíz
Grupo de Investigación en Tomografía (GIT), Universidad Industrial de Santander, Bucaramanga 680002, Colombia
1 shared publication - Daniela Barrera
Grupo de Investigación en Tomografía (GIT), Universidad Industrial de Santander, Bucaramanga 680002, Colombia
1 shared publication - Enrique Mejía-Ospino
Laboratorio de Espectroscopía Atómica y Molecular (LEAM), Universidad Industrial de Santander, Bucaramanga, Colombia
1 shared publication - Holger Steeb
Institute of Applied Mechanics (CE) University of Stuttgart Stuttgart Germany
1 shared publication - Jimena Gómez-Delgado
Universidad Industrial de Santander
1 shared publication Juan Carlos Lizcano Niño
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Instrumentation and Measurement
- Vol. 5, 7500113
Integrated System for Multitechnique Contact Angle Measurements Under Pressure and Temperature Control
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Instrumentation and Measurement
- Vol. 5, 7500113
Open AccessIntegrated System for Multitechnique Contact Angle Measurements Under Pressure and Temperature Control
- Open Access
Numerical Modeling and Multiscale Evaluation of Fe3O4–Graphene Oxide Nanofluids in Electromagnetic Heating for Colombian Heavy Oil Recovery
Electromagnetic heating (EMH) using microwaves has emerged as a promising enhanced oil recovery (EOR) technique, particularly for heavy crude oils where conventional thermal methods encounter technical and environmental challenges. However, its large-scale implementation remains limited due to incomplete understanding of its energy transfer mechanisms. This study proposes an experimental–numerical approach integrating magnetic graphene oxide nanoparticles (Fe3O4@GO) with microwave heating to enhance energy absorption near the wellbore. The nanomaterial was synthesized via a modified Hummer’s method followed by in situ magnetite precipitation and studied through multiple material characterization techniques showing uniform 80 nm particles with superparamagnetic behavior—ideal for EMH applications. Nine experiments were conducted on sand–heavy-oil–water systems with nanoparticle concentrations up to 500 ppm using a laboratory microwave heating prototype. A simulation model was then developed in CMG-STARS for history matching to estimate energy absorption as a function of saturation and nanoparticle concentration. Experiments reached temperatures up to 240 °C, with 653 MJ of effective heat transferred to the target zone over 55 h, as estimated from the input heat required in the simulator for history matching. The results confirm that magnetic graphene oxide nanoparticles enhance thermal efficiency and heat distribution in microwave-assisted EOR.
Open AccessNumerical Modeling and Multiscale Evaluation of Fe3O4–Graphene Oxide Nanofluids in Electromagnetic Heating for Colombian Heavy Oil Recovery
Electromagnetic heating (EMH) using microwaves has emerged as a promising enhanced oil recovery (EOR) technique, particularly for heavy crude oils where conventional thermal methods encounter technical and environmental challenges. However, its large-scale implementation remains limited due to incomplete understanding of its energy transfer mechanisms. This study proposes an experimental–numerical approach integrating magnetic graphene oxide nanoparticles (Fe3O4@GO) with microwave heating to enhance energy absorption near the wellbore. The nanomaterial was synthesized via a modified Hummer’s method followed by in situ magnetite precipitation and studied through multiple material characterization techniques showing uniform 80 nm particles with superparamagnetic behavior—ideal for EMH applications. Nine experiments were conducted on sand–heavy-oil–water systems with nanoparticle concentrations up to 500 ppm using a laboratory microwave heating prototype. A simulation model was then developed in CMG-STARS for history matching to estimate energy absorption as a function of saturation and nanoparticle concentration. Experiments reached temperatures up to 240 °C, with 653 MJ of effective heat transferred to the target zone over 55 h, as estimated from the input heat required in the simulator for history matching. The results confirm that magnetic graphene oxide nanoparticles enhance thermal efficiency and heat distribution in microwave-assisted EOR.
- Open Access
- 24 January 2020
- Published by EDP Sciences in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
- Vol. 75, 5
The effectiveness of computed tomography for the experimental assessment of surfactant-polymer flooding
The Surfactant-Polymer (SP) process is a type of Chemical Enhanced Oil Recovery (CEOR) method. They are still a challenge for the petroleum oil industry mainly because of the difficulty in designing and forecasting the process behavior on the field scale. Therefore, understanding of the phenomena associated with a CEOR process is of vital importance. For these reasons, this work discusses the benefits of Computed Tomography (CT) uses for the experimental assessment of a SP process. The research includes a literature review that allows identifying the main CT usages for petroleum engineering and a discussion concerning the effectiveness of mathematic expressions proposed for the tomography images treatment of two-phase flow displacement. The conducted experimental methodology can be reproduced to assess the benefits of any chemical Enhanced Oil Recovery (EOR) process with CT. Thus, this paper assesses the conventional waterflooding (WF) and SP flooding as secondary and tertiary oil recovery methods. The developed study allowed us to evaluate through CT images the porosity and the saturation profiles along the rock sample. Also, CT processed data enabled checking the volumetric material balance and determine the oil Recovery Factor (RF). The doubled checked SP data showed an RF increase of 17 and 10 percentage points for secondary and tertiary chemical injection schemes respect to conventional waterflooding. Finally, comparative results of the water cut (Wcut) evidenced the mobility ratio improvement and reduction on the remaining oil saturation.
- 24 January 2020
- Published by EDP Sciences in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
- Vol. 75, 5
Open AccessThe effectiveness of computed tomography for the experimental assessment of surfactant-polymer flooding
The Surfactant-Polymer (SP) process is a type of Chemical Enhanced Oil Recovery (CEOR) method. They are still a challenge for the petroleum oil industry mainly because of the difficulty in designing and forecasting the process behavior on the field scale. Therefore, understanding of the phenomena associated with a CEOR process is of vital importance. For these reasons, this work discusses the benefits of Computed Tomography (CT) uses for the experimental assessment of a SP process. The research includes a literature review that allows identifying the main CT usages for petroleum engineering and a discussion concerning the effectiveness of mathematic expressions proposed for the tomography images treatment of two-phase flow displacement. The conducted experimental methodology can be reproduced to assess the benefits of any chemical Enhanced Oil Recovery (EOR) process with CT. Thus, this paper assesses the conventional waterflooding (WF) and SP flooding as secondary and tertiary oil recovery methods. The developed study allowed us to evaluate through CT images the porosity and the saturation profiles along the rock sample. Also, CT processed data enabled checking the volumetric material balance and determine the oil Recovery Factor (RF). The doubled checked SP data showed an RF increase of 17 and 10 percentage points for secondary and tertiary chemical injection schemes respect to conventional waterflooding. Finally, comparative results of the water cut (Wcut) evidenced the mobility ratio improvement and reduction on the remaining oil saturation.
- 10 May 2019
- Published by Instituto Colombiano del Petroleo in Ct&f - Ciencia, Tecnología Y Futuro
- Vol. 9 (1) , 47-63
Assessment of a surfactant- polymer formulation for conditions in a Colombian field
The surfactant-polymer (SP) process is one of the Chemical Enhanced Oil Recovery (CEOR) methods used in the industry. It has been continuously studied; however, it is still a challenge for the petroleum industry due to the difficulty to design the solution to be injected and forecast process performance. This paper is intended to contribute to the design of fluids used in an SP process based on some previously known properties and conditions. Hence, reservoir and fluid properties of a Colombian Field were used as reference parameters to select the polymer and surfactant. Then, the effects of salts, temperature, and surfactant on tailor-made polymer solutions were determined through a rheological study. Ostwald-de Waele and Carreau-Yasuda models adjusted the measured viscosity data against shear rate, while Arrhenius equation fitted viscosity values at 7,8 s-1 against temperature. The surfactant performance was analyzed using phase behavior tests, and the Chun Huh equations determined the interfacial tension (IFT) values. The Bancroft’s rule was used as a qualitative verification tool of the kind of micro- emulsion formed. From rheology, we concluded that the viscous modulus is predominant for all polymer solutions, and the fluid thickness is reduced due to the presence of divalent cations and raise on temperature, salts or surfactant concentration. On the other hand, the observed phase behavior corresponded to a transition Winsor II to I without finding any Winsor III micro-emulsion. Therefore, some criteria were proposed to select the optimal conditions. For the desired conditions, the reduction of IFT reached values ranging in magnitudes of 10-3 to 10-4 [mN/m]. These values are usually associated with an improved oil recovery factor.
- 10 May 2019
- Published by Instituto Colombiano del Petroleo in Ct&f - Ciencia, Tecnología Y Futuro
- Vol. 9 (1) , 47-63
Assessment of a surfactant- polymer formulation for conditions in a Colombian field
The surfactant-polymer (SP) process is one of the Chemical Enhanced Oil Recovery (CEOR) methods used in the industry. It has been continuously studied; however, it is still a challenge for the petroleum industry due to the difficulty to design the solution to be injected and forecast process performance. This paper is intended to contribute to the design of fluids used in an SP process based on some previously known properties and conditions. Hence, reservoir and fluid properties of a Colombian Field were used as reference parameters to select the polymer and surfactant. Then, the effects of salts, temperature, and surfactant on tailor-made polymer solutions were determined through a rheological study. Ostwald-de Waele and Carreau-Yasuda models adjusted the measured viscosity data against shear rate, while Arrhenius equation fitted viscosity values at 7,8 s-1 against temperature. The surfactant performance was analyzed using phase behavior tests, and the Chun Huh equations determined the interfacial tension (IFT) values. The Bancroft’s rule was used as a qualitative verification tool of the kind of micro- emulsion formed. From rheology, we concluded that the viscous modulus is predominant for all polymer solutions, and the fluid thickness is reduced due to the presence of divalent cations and raise on temperature, salts or surfactant concentration. On the other hand, the observed phase behavior corresponded to a transition Winsor II to I without finding any Winsor III micro-emulsion. Therefore, some criteria were proposed to select the optimal conditions. For the desired conditions, the reduction of IFT reached values ranging in magnitudes of 10-3 to 10-4 [mN/m]. These values are usually associated with an improved oil recovery factor.
- Open Access
- 22 January 2018
- Published by Universidad Industrial de Santander in Revista Fuentes El Reventón Energético
- Vol. 16 (1) , 19-35
Effects of salts and temperature on rheological and viscoelastic behavior of low molecular weight HPAM solutions
- 22 January 2018
- Published by Universidad Industrial de Santander in Revista Fuentes El Reventón Energético
- Vol. 16 (1) , 19-35
Open AccessEffects of salts and temperature on rheological and viscoelastic behavior of low molecular weight HPAM solutions