Hongshen Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hongshen Liu has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Seong Han Kim
The Pennsylvania State University
10 shared publications - Joseph Vincent Ryan
Pacific Northwest National Laboratory, Richland, USA
5 shared publications - Jincheng Du
University of North Texas
4 shared publications - Dien Ngo
Department of Chemical Engineering and Materials Research Institute, The Pennsylvania State University, University Park, Pennsylvania 16802, United States
3 shared publications - Gerald S. Frankel
The Ohio State University
3 shared publications John D. Vienna
Energy and Environment Directorate, Pacific Northwest National Laboratory, Richland, WA, USA
3 shared publications
Latest Publications
- 20 November 2021
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 105 (4) , 2847-2857
Flexural stress effect on mechanical and mechanochemical properties of soda lime silicate glass surface
As a means to elucidate the mechanical stress effect on the durability of soda lime silicate (SLS) float glass, a thin glass plate under flexural stress was investigated with X‐ray photoelectron spectroscopy (XPS), specular reflectance infrared (SR‐IR) spectroscopy, nanoindentation, and tribo‐testing. A lab‐built four‐point bending rig was employed to create compressive or tensile stress (around 40 MPa) on the air‐side surface of SLS glass. XPS analysis showed that electric field‐induced sodium ion migration is greatly enhanced in both compressive and tensile stress surfaces. The SR‐IR analysis of the Si‐O‐Si stretch mode revealed that the structural distortion of the silicate network appears to be larger under compressive stress than tensile stress. The elastic and plastic responses of the SLS surface to nanoindentation were significantly altered under the flexural stress conditions even though the magnitude of the flexural stress was less than 0.7% of the applied indentation stress. Compared to the stress‐free surface, the resistance to mechanochemical wear at 90% relative humidity deteriorated under the compressive stress condition, while it just became more scattered under the tensile stress condition. Even though the applied flexural stress was very small, its impact on chemical and structural properties could be surprisingly large. Combining all results in this study and previously published works suggested that the changes observed in nanoindentation and mechanochemical wear behaviors may be associated with the strain in the Si‐O bonds of the silicate network.
- 20 November 2021
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 105 (4) , 2847-2857
Flexural stress effect on mechanical and mechanochemical properties of soda lime silicate glass surface
As a means to elucidate the mechanical stress effect on the durability of soda lime silicate (SLS) float glass, a thin glass plate under flexural stress was investigated with X‐ray photoelectron spectroscopy (XPS), specular reflectance infrared (SR‐IR) spectroscopy, nanoindentation, and tribo‐testing. A lab‐built four‐point bending rig was employed to create compressive or tensile stress (around 40 MPa) on the air‐side surface of SLS glass. XPS analysis showed that electric field‐induced sodium ion migration is greatly enhanced in both compressive and tensile stress surfaces. The SR‐IR analysis of the Si‐O‐Si stretch mode revealed that the structural distortion of the silicate network appears to be larger under compressive stress than tensile stress. The elastic and plastic responses of the SLS surface to nanoindentation were significantly altered under the flexural stress conditions even though the magnitude of the flexural stress was less than 0.7% of the applied indentation stress. Compared to the stress‐free surface, the resistance to mechanochemical wear at 90% relative humidity deteriorated under the compressive stress condition, while it just became more scattered under the tensile stress condition. Even though the applied flexural stress was very small, its impact on chemical and structural properties could be surprisingly large. Combining all results in this study and previously published works suggested that the changes observed in nanoindentation and mechanochemical wear behaviors may be associated with the strain in the Si‐O bonds of the silicate network.
- 5 November 2021
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 105 (4) , 2355-2384
Vibrational spectroscopy analysis of silica and silicate glass networks
Vibrational spectroscopy has been widely used to investigate various structural aspects of the glass network, and there are a plethora of papers reporting subtle but consistent changes in infrared and Raman spectral features of glass upon alterations of glass compositions, thermal histories, mechanical stresses, or surface treatments. However, interpretations of such spectral features are still obscured due to the lack of well‐established physical principles accurately describing vibrational modes of the non‐crystalline glass network. Due to the non‐equilibrium nature of the glass network, three‐dimensionally connected without any long‐range orders, vibrational spectral features of glass cannot be interpreted using the analogy with those of isolated molecular moieties or crystalline counterparts. This feature article explains why such comparisons are outdated and describes the recent advances made from theoretical calculations of vibrational spectral features of amorphous networks or comparisons of computational results with experimental data. For the interpretation of vibrational spectral features of silica and silicate glasses, the following empirical relationships are suggested: (i) the intensity‐weighted peak position of the Si‐O‐Si stretch mode negatively correlates with the weighted average of the Si‐O bond length distribution, and (ii) the broad band of the Si‐O‐Si bending mode negatively correlates with the Si‐O‐Si bond angle distribution. Selected examples of vibrational spectroscopic imaging of surface defects are discussed to deliberate the implication of these findings in the structure‐property relationship of silica and silicate glass materials. Unanswered questions and continuing research challenges are identified.
- 5 November 2021
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 105 (4) , 2355-2384
Vibrational spectroscopy analysis of silica and silicate glass networks
Vibrational spectroscopy has been widely used to investigate various structural aspects of the glass network, and there are a plethora of papers reporting subtle but consistent changes in infrared and Raman spectral features of glass upon alterations of glass compositions, thermal histories, mechanical stresses, or surface treatments. However, interpretations of such spectral features are still obscured due to the lack of well‐established physical principles accurately describing vibrational modes of the non‐crystalline glass network. Due to the non‐equilibrium nature of the glass network, three‐dimensionally connected without any long‐range orders, vibrational spectral features of glass cannot be interpreted using the analogy with those of isolated molecular moieties or crystalline counterparts. This feature article explains why such comparisons are outdated and describes the recent advances made from theoretical calculations of vibrational spectral features of amorphous networks or comparisons of computational results with experimental data. For the interpretation of vibrational spectral features of silica and silicate glasses, the following empirical relationships are suggested: (i) the intensity‐weighted peak position of the Si‐O‐Si stretch mode negatively correlates with the weighted average of the Si‐O bond length distribution, and (ii) the broad band of the Si‐O‐Si bending mode negatively correlates with the Si‐O‐Si bond angle distribution. Selected examples of vibrational spectroscopic imaging of surface defects are discussed to deliberate the implication of these findings in the structure‐property relationship of silica and silicate glass materials. Unanswered questions and continuing research challenges are identified.
- 24 April 2021
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 104 (9) , 4718-4727
Differences in indentation and wear behaviors between the two sides of thermally tempered soda lime silica glass
Thermal tempering is an industrial process widely used to make soda lime silica (SLS) glass panels stronger and tougher. During the tempering process, the upper and bottom sides of the glass may experience different cooling rates, and thus, their properties could be different. This study characterized changes in surface composition and subsurface glass network structures as well as indentation and wear resistance properties of the air‐ and tin‐sides of 6‐mm‐thick SLS window panels faced toward the upper and sliding roller sides during thermal tempering. The results showed that although the chemical and structural differences detected with X‐ray photoelectron spectroscopy and specular reflection infrared spectroscopy are subtle, there are large differences in nanoindentation behaviors and mechanochemical wear properties of the SLS glass surface. The findings of this study provide further insights into the performance difference between the air‐ and tin‐sides of the SLS glass panel treated with thermal tempering.
- 24 April 2021
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 104 (9) , 4718-4727
Differences in indentation and wear behaviors between the two sides of thermally tempered soda lime silica glass
Thermal tempering is an industrial process widely used to make soda lime silica (SLS) glass panels stronger and tougher. During the tempering process, the upper and bottom sides of the glass may experience different cooling rates, and thus, their properties could be different. This study characterized changes in surface composition and subsurface glass network structures as well as indentation and wear resistance properties of the air‐ and tin‐sides of 6‐mm‐thick SLS window panels faced toward the upper and sliding roller sides during thermal tempering. The results showed that although the chemical and structural differences detected with X‐ray photoelectron spectroscopy and specular reflection infrared spectroscopy are subtle, there are large differences in nanoindentation behaviors and mechanochemical wear properties of the SLS glass surface. The findings of this study provide further insights into the performance difference between the air‐ and tin‐sides of the SLS glass panel treated with thermal tempering.
- 13 April 2021
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 104 (8) , 3973-3981
Chemical durability of borosilicate pharmaceutical glasses: Mixed alkaline earth effect with varying [MgO]/[CaO] ratio
Glass for pharmaceutical packaging requires high chemical durability for the safe storage and distribution of newly developed medicines. In borosilicate pharmaceutical glasses which typically contain a mixture of different modifier ions (alkali or alkaline earth), the dependence of the chemical durability on alkaline earth oxide concentrations is not well understood. Here, we have designed a series of borosilicate glasses with systematic substitutions of CaO with MgO while keeping their total concentrations at 13 mol% and a fixed Na 2 O concentration of 12.7 mol%. We used these glasses to investigate the influence of R = [MgO]/([MgO] + [CaO]) on the resistance to aqueous corrosion at 80°C for 40 days. It was found that this type of borosilicate glass undergoes both leaching of modifier ions through an ion exchange process and etching of the glass network, leading to dissolution of the glass surface. Based on the concentration analysis of the Si and B species dissolved into the solution phase, the dissolved layer thickness was found to increase from ~100 to ~170 nm as R increases from 0 to 1. The depth profiling analysis of the glasses retrieved from the solution showed that the concentration of modifier ions (Na + , Ca 2+ , and Mg 2+ ) at the interface between the solution and the corroded glass surface decreased to around 40%–60% of the corresponding bulk concentrations, regardless of R and the leaching of modifier cations resulted in a silica‐rich layer in the surface. The leaching of Ca 2+ and Mg 2+ ions occurred within ~50 and R . The leaching of Na + ions varied monotonically; the thickness of the Na + depletion layer increased from ~100 nm at R = 0 to ~200 nm at R = 1. Vibrational spectroscopy analysis suggested that the partial depletion of the ions may have caused some degree of the network re‐arrangement or re‐polymerization in the corroded layer. Overall, these results suggested that for the borosilicate glass, replacing [CaO] with [MgO] deteriorates the chemical durability in aqueous solution.
- 13 April 2021
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 104 (8) , 3973-3981
Chemical durability of borosilicate pharmaceutical glasses: Mixed alkaline earth effect with varying [MgO]/[CaO] ratio
Glass for pharmaceutical packaging requires high chemical durability for the safe storage and distribution of newly developed medicines. In borosilicate pharmaceutical glasses which typically contain a mixture of different modifier ions (alkali or alkaline earth), the dependence of the chemical durability on alkaline earth oxide concentrations is not well understood. Here, we have designed a series of borosilicate glasses with systematic substitutions of CaO with MgO while keeping their total concentrations at 13 mol% and a fixed Na 2 O concentration of 12.7 mol%. We used these glasses to investigate the influence of R = [MgO]/([MgO] + [CaO]) on the resistance to aqueous corrosion at 80°C for 40 days. It was found that this type of borosilicate glass undergoes both leaching of modifier ions through an ion exchange process and etching of the glass network, leading to dissolution of the glass surface. Based on the concentration analysis of the Si and B species dissolved into the solution phase, the dissolved layer thickness was found to increase from ~100 to ~170 nm as R increases from 0 to 1. The depth profiling analysis of the glasses retrieved from the solution showed that the concentration of modifier ions (Na + , Ca 2+ , and Mg 2+ ) at the interface between the solution and the corroded glass surface decreased to around 40%–60% of the corresponding bulk concentrations, regardless of R and the leaching of modifier cations resulted in a silica‐rich layer in the surface. The leaching of Ca 2+ and Mg 2+ ions occurred within ~50 and R . The leaching of Na + ions varied monotonically; the thickness of the Na + depletion layer increased from ~100 nm at R = 0 to ~200 nm at R = 1. Vibrational spectroscopy analysis suggested that the partial depletion of the ions may have caused some degree of the network re‐arrangement or re‐polymerization in the corroded layer. Overall, these results suggested that for the borosilicate glass, replacing [CaO] with [MgO] deteriorates the chemical durability in aqueous solution.
- 27 September 2020
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 104 (1) , 183-207
Effects of Al:Si and (Al + Na):Si ratios on the properties of the international simple glass, part II: Structure
High‐alumina containing high‐level waste (HLW) will be vitrified at the Waste Treatment Plant at the Hanford Site. The resulting glasses, high in alumina, will have distinct composition‐structure‐property (C‐S‐P) relationships compared to previously studied HLW glasses. These C‐S‐P relationships determine the processability and product durability of glasses and therefore must be understood. The main purpose of this study is to understand the detailed structural changes caused by Al:Si and (Al + Na):Si substitutions in a simplified nuclear waste model glass (ISG, international simple glass) by combining experimental structural characterizations and molecular dynamics (MD) simulations. The structures of these two series of glasses were characterized by neutron total scattering and 27 Al, 23 Na, 29 Si, and 11 B solid‐state nuclear magnetic resonance (NMR) spectroscopy. Additionally, MD simulations were used to generate atomistic structural models of the borosilicate glasses and simulation results were validated by the experimental structural data. Short‐range (eg, bond distance, coordination number, etc) and medium‐range (eg, oxygen speciation, network connectivity, polyhedral linkages) structural features of the borosilicate glasses were systematically investigated as a function of the degree of substitution. The results show that bond distance and coordination number of the cation‐oxygen pairs are relatively insensitive to Al:Si and (Al + Na):Si substitutions with the exception of the B‐O pair. Additionally, the Al:Si substitution results in an increase in tri‐bridging oxygen species, whereas (Al + Na):Si substitution creates nonbridging oxygen species. Charge compensator preferences were found for Si‐[NBO] (Na + ), [3] B‐[NBO] (Na + ), [4] B (mostly Ca 2+ ), [4] Al (nearly equally split Na + and Ca 2+ ), and [6] Zr (mostly Ca 2+ ). The network former‐BO‐network former linkages preferences were also tabulated; Si‐O‐Al and Al‐O‐Al were preferred at the expense of lower Si‐O‐ [3] B and [3] B‐O‐ [3] B linkages. These results provide insights on the structural origins of property changes such as glass‐transition temperature caused by the substitutions, providing a basis for future improvements of theoretical and computer simulation models.
- 27 September 2020
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 104 (1) , 183-207
Effects of Al:Si and (Al + Na):Si ratios on the properties of the international simple glass, part II: Structure
High‐alumina containing high‐level waste (HLW) will be vitrified at the Waste Treatment Plant at the Hanford Site. The resulting glasses, high in alumina, will have distinct composition‐structure‐property (C‐S‐P) relationships compared to previously studied HLW glasses. These C‐S‐P relationships determine the processability and product durability of glasses and therefore must be understood. The main purpose of this study is to understand the detailed structural changes caused by Al:Si and (Al + Na):Si substitutions in a simplified nuclear waste model glass (ISG, international simple glass) by combining experimental structural characterizations and molecular dynamics (MD) simulations. The structures of these two series of glasses were characterized by neutron total scattering and 27 Al, 23 Na, 29 Si, and 11 B solid‐state nuclear magnetic resonance (NMR) spectroscopy. Additionally, MD simulations were used to generate atomistic structural models of the borosilicate glasses and simulation results were validated by the experimental structural data. Short‐range (eg, bond distance, coordination number, etc) and medium‐range (eg, oxygen speciation, network connectivity, polyhedral linkages) structural features of the borosilicate glasses were systematically investigated as a function of the degree of substitution. The results show that bond distance and coordination number of the cation‐oxygen pairs are relatively insensitive to Al:Si and (Al + Na):Si substitutions with the exception of the B‐O pair. Additionally, the Al:Si substitution results in an increase in tri‐bridging oxygen species, whereas (Al + Na):Si substitution creates nonbridging oxygen species. Charge compensator preferences were found for Si‐[NBO] (Na + ), [3] B‐[NBO] (Na + ), [4] B (mostly Ca 2+ ), [4] Al (nearly equally split Na + and Ca 2+ ), and [6] Zr (mostly Ca 2+ ). The network former‐BO‐network former linkages preferences were also tabulated; Si‐O‐Al and Al‐O‐Al were preferred at the expense of lower Si‐O‐ [3] B and [3] B‐O‐ [3] B linkages. These results provide insights on the structural origins of property changes such as glass‐transition temperature caused by the substitutions, providing a basis for future improvements of theoretical and computer simulation models.
- Open Access
- 26 September 2020
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 104 (1) , 167-182
Effects of Al:Si and (Al + Na):Si ratios on the properties of the international simple glass, part I: Physical properties
Understanding composition‐structure‐property relationships of high‐alumina nuclear waste glasses are important for vitrification of nuclear waste at the Hanford Site. Two series of glasses were designed, one with varying Al:Si ratios and the other with (Al + Na):Si ratios based on the international simple glass (ISG, a simplified nuclear waste model glass), with Al 2 O 3 ranging from 0 to 23 mol% (0 to 32 wt%). The glasses were synthesized and characterized using electron probe microanalysis, X‐ray photoelectron spectroscopy, small angle X‐ray scattering, high‐temperature oxide melt solution calorimetry, and infrared spectroscopy. Glasses were crystal free, and the lowest Na 2 O and Al 2 O 3 glass formed an immiscible glass phase. Evolution of various properties—glass‐transition temperature, percentage of 4‐coordinated B, enthalpy of glass formation—and infrared spectroscopy results indicate that structural effects differ based on the glass series.
- 26 September 2020
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 104 (1) , 167-182
Open AccessEffects of Al:Si and (Al + Na):Si ratios on the properties of the international simple glass, part I: Physical properties
Understanding composition‐structure‐property relationships of high‐alumina nuclear waste glasses are important for vitrification of nuclear waste at the Hanford Site. Two series of glasses were designed, one with varying Al:Si ratios and the other with (Al + Na):Si ratios based on the international simple glass (ISG, a simplified nuclear waste model glass), with Al 2 O 3 ranging from 0 to 23 mol% (0 to 32 wt%). The glasses were synthesized and characterized using electron probe microanalysis, X‐ray photoelectron spectroscopy, small angle X‐ray scattering, high‐temperature oxide melt solution calorimetry, and infrared spectroscopy. Glasses were crystal free, and the lowest Na 2 O and Al 2 O 3 glass formed an immiscible glass phase. Evolution of various properties—glass‐transition temperature, percentage of 4‐coordinated B, enthalpy of glass formation—and infrared spectroscopy results indicate that structural effects differ based on the glass series.
- 13 July 2020
- Published by Springer Nature in Nature Materials
- Vol. 19 (9) , 962-963
Reply to: How much does corrosion of nuclear waste matrices matter
- 13 July 2020
- Published by Springer Nature in Nature Materials
- Vol. 19 (9) , 962-963
Reply to: How much does corrosion of nuclear waste matrices matter
- Open Access
- 3 April 2020
- Published by Springer Nature in npj Materials Degradation
- Vol. 4 (1) , 1-15
Near-field corrosion interactions between glass and corrosion resistant alloys
This study explores the corrosion interactions between model nuclear waste glass materials and corrosion resistant alloys, under accelerated conditions that simulate the near field of a nuclear waste repository. The interactions between the corrosion of stainless steel (SS) 316, alloy G30, or alloy 625, and international simple glass or soda-lime silica glass are systematically studied. The dissimilar materials were exposed in close proximity to each other in different electrolytes at 90 °C. After exposure, the glass surface exposed near metals showed different regimes of corrosion, with distinct surface morphologies and chemistries that were likely affected by the local environment created by the localized corrosion of metals. Surface and solution analyses showed that the corrosion rate of glass was enhanced by the presence of metals. Infrared spectroscopy data suggested the local build-up of stresses in the contact area of glass, which may lead to the mechanical instability of the glass alteration layer. On the other hand, the effect of glass on metal corrosion is strongly dependent on the leaching solution. In electrolytes containing abundant aggressive anions such as Cl−, glass seems to suppress the localized corrosion of SS by the precipitation of a Si-rich surface film that protects the SS substrate from solutions. However, in less aggressive electrolytes, the corrosion rate of SS was increased by the presence of glass corrosion products. Overall, our study showed that the hidden and localized damage on glass in contact with metals may enhance the release rate of glass components compared to typical uniform glass corrosion.
- 3 April 2020
- Published by Springer Nature in npj Materials Degradation
- Vol. 4 (1) , 1-15
Open AccessNear-field corrosion interactions between glass and corrosion resistant alloys
This study explores the corrosion interactions between model nuclear waste glass materials and corrosion resistant alloys, under accelerated conditions that simulate the near field of a nuclear waste repository. The interactions between the corrosion of stainless steel (SS) 316, alloy G30, or alloy 625, and international simple glass or soda-lime silica glass are systematically studied. The dissimilar materials were exposed in close proximity to each other in different electrolytes at 90 °C. After exposure, the glass surface exposed near metals showed different regimes of corrosion, with distinct surface morphologies and chemistries that were likely affected by the local environment created by the localized corrosion of metals. Surface and solution analyses showed that the corrosion rate of glass was enhanced by the presence of metals. Infrared spectroscopy data suggested the local build-up of stresses in the contact area of glass, which may lead to the mechanical instability of the glass alteration layer. On the other hand, the effect of glass on metal corrosion is strongly dependent on the leaching solution. In electrolytes containing abundant aggressive anions such as Cl−, glass seems to suppress the localized corrosion of SS by the precipitation of a Si-rich surface film that protects the SS substrate from solutions. However, in less aggressive electrolytes, the corrosion rate of SS was increased by the presence of glass corrosion products. Overall, our study showed that the hidden and localized damage on glass in contact with metals may enhance the release rate of glass components compared to typical uniform glass corrosion.
- Top Cited Papers
- 27 January 2020
- Published by Springer Nature in Nature Materials
- Vol. 19 (3) , 310-316
Self-accelerated corrosion of nuclear waste forms at material interfaces
The US plan for high-level nuclear waste includes the immobilization of long-lived radionuclides in glass or ceramic waste forms in stainless-steel canisters for disposal in deep geological repositories. Here we report that, under simulated repository conditions, corrosion could be significantly accelerated at the interfaces of different barrier materials, which has not been considered in the current safety and performance assessment models. Severe localized corrosion was found at the interfaces between stainless steel and a model nuclear waste glass and between stainless steel and a ceramic waste form. The accelerated corrosion can be attributed to changes of solution chemistry and local acidity/alkalinity within a confined space, which significantly alter the corrosion of both the waste-form materials and the metallic canisters. The corrosion that is accelerated by the interface interaction between dissimilar materials could profoundly impact the service life of the nuclear waste packages, which, therefore, should be carefully considered when evaluating the performance of waste forms and their packages. Moreover, compatible barriers should be selected to further optimize the performance of the geological repository system.
- 27 January 2020
- Published by Springer Nature in Nature Materials
- Vol. 19 (3) , 310-316
Top Cited PapersSelf-accelerated corrosion of nuclear waste forms at material interfaces
The US plan for high-level nuclear waste includes the immobilization of long-lived radionuclides in glass or ceramic waste forms in stainless-steel canisters for disposal in deep geological repositories. Here we report that, under simulated repository conditions, corrosion could be significantly accelerated at the interfaces of different barrier materials, which has not been considered in the current safety and performance assessment models. Severe localized corrosion was found at the interfaces between stainless steel and a model nuclear waste glass and between stainless steel and a ceramic waste form. The accelerated corrosion can be attributed to changes of solution chemistry and local acidity/alkalinity within a confined space, which significantly alter the corrosion of both the waste-form materials and the metallic canisters. The corrosion that is accelerated by the interface interaction between dissimilar materials could profoundly impact the service life of the nuclear waste packages, which, therefore, should be carefully considered when evaluating the performance of waste forms and their packages. Moreover, compatible barriers should be selected to further optimize the performance of the geological repository system.
- 25 January 2020
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 103 (6) , 3575-3589
Searching for correlations between vibrational spectral features and structural parameters of silicate glass network
Infrared (IR) and Raman spectroscopic features of silicate glasses are often interpreted based on the analogy with those of smaller molecules, molecular clusters, or crystalline counterparts; this study tests the accuracy and validity of these widely cited peak assignment schemes by comparing vibrational spectral features with bond parameters of the glass network created by molecular dynamics (MD) simulations. A series of sodium silicate glasses with compositions of [Na2O]x[Al2O3]2[SiO2]98−x with x = 7, 12, 17, and 22 were synthesized and analyzed with IR and Raman. A silica glass substrate and a crystalline quartz were also analyzed for comparison. Glass structures with the same compositions were generated with MD simulations using three types of potentials: fixed partial charge pairwise (Teter), partial diffuse charge potential (MGFF), and bond order‐based charge transfer potential (ReaxFF). The comparison of simulated and experimental IR spectra showed that, among these three potentials tested, ReaxFF reproduces the concentration dependence of spectral features closest to the experimentally observed trend. Thus, the bond length and angle distributions as well as Si–Qn species and ring size distributions of silica and sodium silicate glasses were obtained from ReaxFF‐MD simulations and further compared with the peak assignment or deconvolution schemes—which have been widely used since 1970s and 1980s—(a) correlation between the IR peak position in the Si–O stretch region (1050‐1120 cm−1) and the Si–O–Si bond angle; (b) deconvolution of the Raman bands in the Si–O stretch region with the Qn speciation; and (c) assignment of the Raman bands in the 420‐600 cm−1 region to the bending modes of (SiO)n rings with different sizes (typically, n = 3‐6). The comparisons showed that none of these widely used methods is congruent with the bond parameters or structures of silicate glass networks produced via ReaxFF‐MD simulations. This finding invokes that the adequacy of these spectral interpretation methods must be questioned. Alternative interpretations are proposed, which are to be tested independently in future studies.
- 25 January 2020
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 103 (6) , 3575-3589
Searching for correlations between vibrational spectral features and structural parameters of silicate glass network
Infrared (IR) and Raman spectroscopic features of silicate glasses are often interpreted based on the analogy with those of smaller molecules, molecular clusters, or crystalline counterparts; this study tests the accuracy and validity of these widely cited peak assignment schemes by comparing vibrational spectral features with bond parameters of the glass network created by molecular dynamics (MD) simulations. A series of sodium silicate glasses with compositions of [Na2O]x[Al2O3]2[SiO2]98−x with x = 7, 12, 17, and 22 were synthesized and analyzed with IR and Raman. A silica glass substrate and a crystalline quartz were also analyzed for comparison. Glass structures with the same compositions were generated with MD simulations using three types of potentials: fixed partial charge pairwise (Teter), partial diffuse charge potential (MGFF), and bond order‐based charge transfer potential (ReaxFF). The comparison of simulated and experimental IR spectra showed that, among these three potentials tested, ReaxFF reproduces the concentration dependence of spectral features closest to the experimentally observed trend. Thus, the bond length and angle distributions as well as Si–Qn species and ring size distributions of silica and sodium silicate glasses were obtained from ReaxFF‐MD simulations and further compared with the peak assignment or deconvolution schemes—which have been widely used since 1970s and 1980s—(a) correlation between the IR peak position in the Si–O stretch region (1050‐1120 cm−1) and the Si–O–Si bond angle; (b) deconvolution of the Raman bands in the Si–O stretch region with the Qn speciation; and (c) assignment of the Raman bands in the 420‐600 cm−1 region to the bending modes of (SiO)n rings with different sizes (typically, n = 3‐6). The comparisons showed that none of these widely used methods is congruent with the bond parameters or structures of silicate glass networks produced via ReaxFF‐MD simulations. This finding invokes that the adequacy of these spectral interpretation methods must be questioned. Alternative interpretations are proposed, which are to be tested independently in future studies.