Tomáš Katrňák
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tomáš Katrňák has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Jaroslav Juračka
Institute of Aerospace Engineering, Faculty of Mechanical Engineering, Brno University of Technology, Brno, Czech Republic
2 shared publications - Ivo Jebáček
Institute of Aerospace Engineering, Brno University of Technology, 60190 Brno, Czech Republic
1 shared publication Katarzyna Łabno
Zakłady Mechaniczne Tarnów S.A.
1 shared publication- Ryszard Perłowski
Rzeszów University of Technology
1 shared publication - Władysław Zielecki
The Faculty of Mechanical Engineering and Aeronautics, Rzeszów University of Technology, Powstańców Warszawy 12, 35-959 Rzeszów
1 shared publication - Łukasz Bąk
Department of Materials Forming and Processing, Rzeszow University of Technology, Powstancow Warszawy 8, 35-959 Rzeszow, Poland
1 shared publication
Latest Publications
- Open Access
- 1 January 2023
- Published by Rzeszow University of Technology in Advances in Mechanical and Materials Engineering
- Vol. 40 (1) , 5-13
Experimental Research on the Influence of Structural Modifications of Adherends on the Load - Bearing Capacity of Lap Joints of S235JR Steel Sheets
The paper presents the results of the research determining the impact of structural modifications of adherends on the load capacity of the joints determined in the static shear test. Tests of adhesive lap joints of S235JR steel sheets bonded with Araldite 2014-2 epoxy adhesive are described. The influence of technologically simple structural modifications was investigated; it consisted in making notches and holes at the leading edge of the adherends. These modifications were aimed at bringing about local flexibility of the joint in the sensitive area of stress concentration. Based on experimental studies, it was shown that there is a possibility of increasing the load-bearing capacity of the joint due to the applied modifications; in the most favorable variant, an increase in the load-bearing capacity by 15.9% compared to the base variant was demonstrated. The tests confirmed that the notches filled with the adhesive in the front part of the adherends can significantly improve the strength properties of joint, while the considered modifications in the form of holes do not have a significant impact on the properties of the adherends. W pracy przedstawiono wyniki badań określające wpływ modyfikacji konstrukcyjnych elementów klejonych na nośność połączeń określoną na podstawie próby statycznego ścinania. Opisano badania zakładkowych połączeń klejonych blach ze stali S235JR łączonych klejem epoksydowym Araldite 2014-2. Określono wpływ prostych z technologicznego punktu widzenia modyfikacji konstrukcyjnych, polegających na wykonaniu wcięć oraz otworów przy czołowych krawędziach klejonych blach. Modyfikacje te miały na celu doprowadzenie do lokalnego uelastycznienia połączenia we wrażliwym obszarze, w którym dochodzi do koncentracji naprężeń. Na podstawie badań eksperymentalnych wykazano, że istnieje możliwość zwiększenia nośności połączenia dzięki zastosowanym modyfikacjom, w najkorzystniejszym wariancie wykazano wzrost nośności o 15,9% w stosunku do wariantu podstawowego. Przeprowadzone badania potwierdziły, że wypełnione klejem wcięć w czołowym obszarze połączenia może prowadzić do redukcji spiętrzenia naprężeń, co prowadzi do znaczącej poprawy właściwości wytrzymałościowych złącza klejowego. Wykazano również, że modyfikacje w postaci otworów o rozważanych wymiarach nie mają istotnego wpływu na właściwości połączeń.
- 1 January 2023
- Published by Rzeszow University of Technology in Advances in Mechanical and Materials Engineering
- Vol. 40 (1) , 5-13
Open AccessExperimental Research on the Influence of Structural Modifications of Adherends on the Load - Bearing Capacity of Lap Joints of S235JR Steel Sheets
The paper presents the results of the research determining the impact of structural modifications of adherends on the load capacity of the joints determined in the static shear test. Tests of adhesive lap joints of S235JR steel sheets bonded with Araldite 2014-2 epoxy adhesive are described. The influence of technologically simple structural modifications was investigated; it consisted in making notches and holes at the leading edge of the adherends. These modifications were aimed at bringing about local flexibility of the joint in the sensitive area of stress concentration. Based on experimental studies, it was shown that there is a possibility of increasing the load-bearing capacity of the joint due to the applied modifications; in the most favorable variant, an increase in the load-bearing capacity by 15.9% compared to the base variant was demonstrated. The tests confirmed that the notches filled with the adhesive in the front part of the adherends can significantly improve the strength properties of joint, while the considered modifications in the form of holes do not have a significant impact on the properties of the adherends. W pracy przedstawiono wyniki badań określające wpływ modyfikacji konstrukcyjnych elementów klejonych na nośność połączeń określoną na podstawie próby statycznego ścinania. Opisano badania zakładkowych połączeń klejonych blach ze stali S235JR łączonych klejem epoksydowym Araldite 2014-2. Określono wpływ prostych z technologicznego punktu widzenia modyfikacji konstrukcyjnych, polegających na wykonaniu wcięć oraz otworów przy czołowych krawędziach klejonych blach. Modyfikacje te miały na celu doprowadzenie do lokalnego uelastycznienia połączenia we wrażliwym obszarze, w którym dochodzi do koncentracji naprężeń. Na podstawie badań eksperymentalnych wykazano, że istnieje możliwość zwiększenia nośności połączenia dzięki zastosowanym modyfikacjom, w najkorzystniejszym wariancie wykazano wzrost nośności o 15,9% w stosunku do wariantu podstawowego. Przeprowadzone badania potwierdziły, że wypełnione klejem wcięć w czołowym obszarze połączenia może prowadzić do redukcji spiętrzenia naprężeń, co prowadzi do znaczącej poprawy właściwości wytrzymałościowych złącza klejowego. Wykazano również, że modyfikacje w postaci otworów o rozważanych wymiarach nie mają istotnego wpływu na właściwości połączeń.
- Open Access
- 22 January 2020
- Published by Vilnius Gediminas Technical University in Aviation
- Vol. 23 (3) , 83-90
RESEARCH OF EFFECTS OF DEFECTS ON STABILITY FAILURES OF SEMI-MONOCOQUE STIFFENERS
This article presents further results of the research of effects of model defects on the local buckling of compressed stiffeners in nonlinear finite element (FE) analyses. The main outcomes are confirmation of trends for 10 sets of profile dimensions, final validations of various sets of FE simulations, and designs of practical types of defects with appropriate ratio values. A single node defect and then complex types of defects with alternating distributions of node shifts along one edge, two free flange edges, one flange surface and both flange surfaces are analyzed in this research project. First parts of this paper describe designed FE models with defects, their effects on simulation results, colored graphic visualizations with stress scales and determinations of the sudden failure of stability in the local mode. Then, particular results of FE analyses are validated by a comparison with the results of analytical methods of stability failure. Final detail comparisons of analytical and FE simulation results with data of experimental tests confirm predicted critical buckling forces. The validation of results and design parameters together with the knowledge of effects of model defects on buckling behaviors allows more accurate simulations of internal stiffeners of thin-walled semi-monocoque structures.
- 22 January 2020
- Published by Vilnius Gediminas Technical University in Aviation
- Vol. 23 (3) , 83-90
Open AccessRESEARCH OF EFFECTS OF DEFECTS ON STABILITY FAILURES OF SEMI-MONOCOQUE STIFFENERS
This article presents further results of the research of effects of model defects on the local buckling of compressed stiffeners in nonlinear finite element (FE) analyses. The main outcomes are confirmation of trends for 10 sets of profile dimensions, final validations of various sets of FE simulations, and designs of practical types of defects with appropriate ratio values. A single node defect and then complex types of defects with alternating distributions of node shifts along one edge, two free flange edges, one flange surface and both flange surfaces are analyzed in this research project. First parts of this paper describe designed FE models with defects, their effects on simulation results, colored graphic visualizations with stress scales and determinations of the sudden failure of stability in the local mode. Then, particular results of FE analyses are validated by a comparison with the results of analytical methods of stability failure. Final detail comparisons of analytical and FE simulation results with data of experimental tests confirm predicted critical buckling forces. The validation of results and design parameters together with the knowledge of effects of model defects on buckling behaviors allows more accurate simulations of internal stiffeners of thin-walled semi-monocoque structures.
- Open Access
- 27 March 2017
- Published by Vilnius Gediminas Technical University in Aviation
- Vol. 21 (1) , 29-34
Topometry FEM optimization of the wing structure of the transport aircraft
The article presents the topometry optimization of the critical semi-shell wing structure of the aircraft in the Commuter category of the CS-23 regulation standard (EASA 2012). Modern finite element (FE) optimization methods are used. The main outcome is that the milled integral lower wing panel allows significant weight savings due to an optimization of the thickness of each skin segment. The FE model validation with the analytical software and the selection of structural constraints and requirements for the optimization are described in this article. Also, a final stress analysis and a complex load capacity analysis validate required properties of designed structural modifications with an optimal stress distribution. Additionally the analysis of weight savings and elongation of the fatigue durability according to the Damage tolerance methodology was done.
- 27 March 2017
- Published by Vilnius Gediminas Technical University in Aviation
- Vol. 21 (1) , 29-34
Open AccessTopometry FEM optimization of the wing structure of the transport aircraft
The article presents the topometry optimization of the critical semi-shell wing structure of the aircraft in the Commuter category of the CS-23 regulation standard (EASA 2012). Modern finite element (FE) optimization methods are used. The main outcome is that the milled integral lower wing panel allows significant weight savings due to an optimization of the thickness of each skin segment. The FE model validation with the analytical software and the selection of structural constraints and requirements for the optimization are described in this article. Also, a final stress analysis and a complex load capacity analysis validate required properties of designed structural modifications with an optimal stress distribution. Additionally the analysis of weight savings and elongation of the fatigue durability according to the Damage tolerance methodology was done.