Alvian Kuzmych
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alvian Kuzmych has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Serhii Stepanenko
Institute of Mechanics and Automation of Agro-Industrial Production, National Academy of Agrarian Sciences of Ukraine
22 shared publications - Mykhailo Aneliak
Institute of Mechanics and Automatics of Agroindustrial Production of the National academy of Agrarian Sciences of Ukraine
9 shared publications - Roman Kalinichenko
National University of Life and Environmental Sciences of Ukraine
8 shared publications - Viktor Dnes
Institute of Mechanics and Automation of Agro-Industrial Production of the National Academy of Agrarian Sciences of Ukraine
8 shared publications - Andrii Boris
Institute of Mechanics and Automatics of Agroindustrial Production of the National Academy of Agrarian Sciences of Ukraine, Glevakha, Fastiv district, Kyiv region, Ukraine
6 shared publications - I. S. Popadyuk
Institute of Mechanics and Automation of Agro-Industrial Production, National Academy of Agrarian Sciences of Ukraine
5 shared publications
Latest Publications
- Open Access
- 12 October 2026
- Published by Vinnytsia National Agrarian University in Vibrations in engineering and technology
- No. 3(122),p. 204
EXPERIMENTAL RESULTS OF THE SEPARATION PROCESS OF GRAIN MATERIALS IN A PNEUMOCENTRIFUGAL SEPARATOR
The article presents the results of experimental studies of the separation process of grain materials in a pneumocentrifugal separator. The relevance of the study is determined by the need to improve the efficiency of cleaning and fractionation of grain mixtures based on their aerodynamic properties through the simultaneous use of airflow and centrifugal forces. The combination of pneumatic and centrifugal separation principles makes it possible to intensify particle movement in the working zone, ensure their differentiated movement depending on their physical, mechanical, and aerodynamic properties, and improve the controllability of the separation process. The aim of the study is to experimentally establish the regularities of the grain material separation process in a pneumocentrifugal separator and to determine the effect of the main design, technological, and operating parameters on the qualitative and quantitative performance indicators of its operation. Experimental studies were conducted using a laboratory-scale pneumocentrifugal separator, with the main technological parameters of the process determined under different operating conditions. During the experiments, the parameters governing the kinematic interaction of the grain material with the working surface and airflow were varied. The process efficiency was evaluated based on the yield of individual fractions, their degree of purity, the completeness of removal of mixture components, and losses of sound grain. The nature of changes in the technological parameters depending on the operating conditions of the pneumocentrifugal separator was established. It was shown that changes in airflow velocity and the kinematic parameters of the working element significantly affect particle trajectories, their residence time in the separation zone, and the conditions under which grain mixture components enter the corresponding fractions. As the airflow regime changes, the ratio of aerodynamic, centrifugal, gravitational, and drag forces changes, determining the intensity and selectivity of the separation process. Based on the experimental data, ranges of rational operating conditions of the separator were determined, under which the most favorable balance between separation efficiency, quality of the resulting fractions, and losses of sound grain is achieved. The results obtained can be used to substantiate the design and technological parameters of pneumocentrifugal separators, improve working elements and airflow control systems, and develop recommendations for the practical application of machines for cleaning and fractionating grain materials. The scientific novelty of the study lies in establishing experimental regularities in the variation of grain material separation performance indicators depending on the main operating parameters of the pneumocentrifugal separator and determining their relationship with the quality of the resulting fractions. The practical significance of the results obtained lies in the possibility of using the established regularities to select rational operating conditions and further improve the design of pneumocentrifugal separators.
- 12 October 2026
- Published by Vinnytsia National Agrarian University in Vibrations in engineering and technology
- No. 3(122),p. 204
Open AccessEXPERIMENTAL RESULTS OF THE SEPARATION PROCESS OF GRAIN MATERIALS IN A PNEUMOCENTRIFUGAL SEPARATOR
The article presents the results of experimental studies of the separation process of grain materials in a pneumocentrifugal separator. The relevance of the study is determined by the need to improve the efficiency of cleaning and fractionation of grain mixtures based on their aerodynamic properties through the simultaneous use of airflow and centrifugal forces. The combination of pneumatic and centrifugal separation principles makes it possible to intensify particle movement in the working zone, ensure their differentiated movement depending on their physical, mechanical, and aerodynamic properties, and improve the controllability of the separation process. The aim of the study is to experimentally establish the regularities of the grain material separation process in a pneumocentrifugal separator and to determine the effect of the main design, technological, and operating parameters on the qualitative and quantitative performance indicators of its operation. Experimental studies were conducted using a laboratory-scale pneumocentrifugal separator, with the main technological parameters of the process determined under different operating conditions. During the experiments, the parameters governing the kinematic interaction of the grain material with the working surface and airflow were varied. The process efficiency was evaluated based on the yield of individual fractions, their degree of purity, the completeness of removal of mixture components, and losses of sound grain. The nature of changes in the technological parameters depending on the operating conditions of the pneumocentrifugal separator was established. It was shown that changes in airflow velocity and the kinematic parameters of the working element significantly affect particle trajectories, their residence time in the separation zone, and the conditions under which grain mixture components enter the corresponding fractions. As the airflow regime changes, the ratio of aerodynamic, centrifugal, gravitational, and drag forces changes, determining the intensity and selectivity of the separation process. Based on the experimental data, ranges of rational operating conditions of the separator were determined, under which the most favorable balance between separation efficiency, quality of the resulting fractions, and losses of sound grain is achieved. The results obtained can be used to substantiate the design and technological parameters of pneumocentrifugal separators, improve working elements and airflow control systems, and develop recommendations for the practical application of machines for cleaning and fractionating grain materials. The scientific novelty of the study lies in establishing experimental regularities in the variation of grain material separation performance indicators depending on the main operating parameters of the pneumocentrifugal separator and determining their relationship with the quality of the resulting fractions. The practical significance of the results obtained lies in the possibility of using the established regularities to select rational operating conditions and further improve the design of pneumocentrifugal separators.
- Open Access
- 12 October 2026
- Published by Vinnytsia National Agrarian University in Engineering, Energy, Transport AIC
- p. 45
MICROPROCESSOR SYSTEM FOR DIGITAL CONTROL OF ELECTRIC DRIVES OF WORKING ELEMENTS OF GRAIN CLEANING MACHINES
This paper addresses the development and experimental validation of a digital control system for the electric drives of grain-cleaning machine working units based on the SAKO SKI780 frequency converter, the Arduino Uno microcontroller platform and the Modbus RTU communication protocol. The proposed system is intended to improve the accuracy, flexibility and reliability of electric-drive control during grain-cleaning operations. The general architecture of the control system, the principles of interaction between its main hardware components, the control algorithm for generating and transmitting commands through the RS-485 interface, and the corresponding software implementation of the microprocessor-based control system are presented. Particular attention is paid to ensuring stable and reliable data exchange between the microcontroller and the frequency converter, as well as to the correct formation of control commands for regulating rotational speed and other operating parameters of the electric drive. The developed software makes it possible to set the required operating modes, transmit control signals, process feedback data and coordinate the operation of individual machine units. Experimental studies confirmed the stable operation of the proposed control system and its ability to accurately reproduce specified speed modes under varying load conditions. The obtained results demonstrate that the use of digital control makes it possible to reduce transient response time compared with conventional analog control methods, thereby improving the stability of electric-drive operation and the consistency of grain separation. The developed system also provides flexible adjustment of rotational speed and facilitates centralized control of individual working units. The proposed approach can be considered a promising solution for the automation and modernization of grain-cleaning equipment. Further development may involve the integration of sensors for monitoring grain quality, drive load and material flow, enabling adaptive control algorithms and automatic adjustment of operating parameters in response to changing technological conditions. The obtained results provide a scientific and practical basis for improving the energy efficiency, reliability and technological performance of modern grain-cleaning machines.
- 12 October 2026
- Published by Vinnytsia National Agrarian University in Engineering, Energy, Transport AIC
- p. 45
Open AccessMICROPROCESSOR SYSTEM FOR DIGITAL CONTROL OF ELECTRIC DRIVES OF WORKING ELEMENTS OF GRAIN CLEANING MACHINES
This paper addresses the development and experimental validation of a digital control system for the electric drives of grain-cleaning machine working units based on the SAKO SKI780 frequency converter, the Arduino Uno microcontroller platform and the Modbus RTU communication protocol. The proposed system is intended to improve the accuracy, flexibility and reliability of electric-drive control during grain-cleaning operations. The general architecture of the control system, the principles of interaction between its main hardware components, the control algorithm for generating and transmitting commands through the RS-485 interface, and the corresponding software implementation of the microprocessor-based control system are presented. Particular attention is paid to ensuring stable and reliable data exchange between the microcontroller and the frequency converter, as well as to the correct formation of control commands for regulating rotational speed and other operating parameters of the electric drive. The developed software makes it possible to set the required operating modes, transmit control signals, process feedback data and coordinate the operation of individual machine units. Experimental studies confirmed the stable operation of the proposed control system and its ability to accurately reproduce specified speed modes under varying load conditions. The obtained results demonstrate that the use of digital control makes it possible to reduce transient response time compared with conventional analog control methods, thereby improving the stability of electric-drive operation and the consistency of grain separation. The developed system also provides flexible adjustment of rotational speed and facilitates centralized control of individual working units. The proposed approach can be considered a promising solution for the automation and modernization of grain-cleaning equipment. Further development may involve the integration of sensors for monitoring grain quality, drive load and material flow, enabling adaptive control algorithms and automatic adjustment of operating parameters in response to changing technological conditions. The obtained results provide a scientific and practical basis for improving the energy efficiency, reliability and technological performance of modern grain-cleaning machines.
- Open Access
- 22 September 2026
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 13 (2) , F26
Mathematical Modeling and Parameter Identification of Seed Motion During Density Separation in a Vibro-Pneumo-Fluidized Bed
Vibro-pneumatic separation is widely used to sort grain mixtures by density. However, optimizing operational regimes requires an accurate description of the dynamics of internal bed resistance. This study aims to develop a mathematical model of grain movement in a vibro-pneumo-fluidized bed based on simplified physical and mechanical concepts, and to identify its parameters using direct experimental data. Experimental studies on particle immersion kinetics were conducted to identify empirical medium resistance coefficients. Numerical simulations of spatial trajectories for coarse and fine seed fractions were executed using the 4th-order Runge-Kutta numerical integration using the computer algebra system. Model calibration confirmed that resistance anisotropy and inter-layer shear friction significantly affect longitudinal particle translation. The coupled influence of seed layer height and superficial airflow velocity on the target particle immersion time was evaluated using a two-factor central composite rotatable design (CCRD). The regression model proved that layer height exerts the dominant positive effect on the target particle immersion time. Simultaneously, increasing airflow velocity accelerates descent by enhancing the bed’s porosity. Validation demonstrated high convergence between numerical simulation trajectories and empirical CCRD data, with relative errors below 9.4 %. The derived response surface equations provide a reliable foundation for optimizing the operating regimes of vibro-pneumatic seed separators.
- 22 September 2026
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 13 (2) , F26
Open AccessMathematical Modeling and Parameter Identification of Seed Motion During Density Separation in a Vibro-Pneumo-Fluidized Bed
Vibro-pneumatic separation is widely used to sort grain mixtures by density. However, optimizing operational regimes requires an accurate description of the dynamics of internal bed resistance. This study aims to develop a mathematical model of grain movement in a vibro-pneumo-fluidized bed based on simplified physical and mechanical concepts, and to identify its parameters using direct experimental data. Experimental studies on particle immersion kinetics were conducted to identify empirical medium resistance coefficients. Numerical simulations of spatial trajectories for coarse and fine seed fractions were executed using the 4th-order Runge-Kutta numerical integration using the computer algebra system. Model calibration confirmed that resistance anisotropy and inter-layer shear friction significantly affect longitudinal particle translation. The coupled influence of seed layer height and superficial airflow velocity on the target particle immersion time was evaluated using a two-factor central composite rotatable design (CCRD). The regression model proved that layer height exerts the dominant positive effect on the target particle immersion time. Simultaneously, increasing airflow velocity accelerates descent by enhancing the bed’s porosity. Validation demonstrated high convergence between numerical simulation trajectories and empirical CCRD data, with relative errors below 9.4 %. The derived response surface equations provide a reliable foundation for optimizing the operating regimes of vibro-pneumatic seed separators.
- 9 June 2026
- Published by Institute of Physical Optics in Ukrainian Journal of Physical Optics
- Vol. 27 (4) , 04016-04033
INTELLIGENT SOYBEAN SEED FRACTION SEGMENTATION SYSTEM BASED ON THE INTEGRATION OF SPECTRAL SIGNATURES AND PRECISION NEURAL NETWORK ARCHITECTURES
- 9 June 2026
- Published by Institute of Physical Optics in Ukrainian Journal of Physical Optics
- Vol. 27 (4) , 04016-04033
INTELLIGENT SOYBEAN SEED FRACTION SEGMENTATION SYSTEM BASED ON THE INTEGRATION OF SPECTRAL SIGNATURES AND PRECISION NEURAL NETWORK ARCHITECTURES
- Open Access
- 5 May 2026
- Published by Publishing House Helvetica (Publications) in Bulletin of Sumy National Agrarian University. The series: Mechanization and Automation of Production Processes
- No. 1,p. 102-109
ДОСЛІДЖЕННЯ РУХУ ЗЕРНОВОГО МАТЕРІАЛУ В ПРОЦЕСАХ ВІБРОПНЕВМОРЕШЕТНОЇ СЕПАРАЦІЇ
У статті наведено результати теоретичних та експериментальних досліджень руху зернового матеріалу в процесах вібропневморешетної сепарації за умов коливального руху робочої поверхні. Об’єктом дослідження є зерновий матеріал, що перебуває у віброзрідженому стані на решеті вібропневмосепаратора, оснащеного додатковими пасивними робочими органами у вигляді розпушувачів. Актуальність роботи зумовлена обмеженою продуктивністю сучасних вібропневморешетних сепараторів, яка пов’язана з недостатньою інтенсивністю розпушення зернового шару та нерівномірним перерозподілом частинок за висотою шару. Метою дослідження є встановлення закономірностей переміщення та занурення частинок зерна у шарі матеріалу, а також обґрунтування раціональних конструктивних параметрів пасивних розпушувачів, які забезпечують інтенсифікацію процесу сепарації та підвищення його ефективності. У роботі застосовано комплексний підхід, що поєднує аналітичне моделювання і експериментальні дослідження. Побудовано механіко-математичну модель руху окремої частинки зерна у віброзрідженому шарі з урахуванням дії сил гравітації, інерції, напруженого стану сипкого середовища та додаткової виштовхуючої сили, зумовленої взаємодією зернового шару з пасивними розпушувачами. На основі отриманих рівнянь визначено аналітичні залежності, що описують траєкторії руху частинок зерна вздовж робочої поверхні решета, а також у напрямку їх занурення до просіювальних отворів. Проведено графічну інтерпретацію характеру переміщення частинок, яка підтверджує інтенсифікацію рекомбінації зернового матеріалу за висотою шару при використанні додаткових пасивних робочих органів. Експериментальні дослідження виконано на спеціально розробленій вібропневмосепарувальній установці з варіюванням конструктивних параметрів пасивних розпушувачів. Установлено, що раціональні значення ширини полки та кута розхилу розпушувачів сприяють активному розпушенню зернового шару, формуванню каналів у сипкому середовищі та більш інтенсивному просіюванню дрібних фракцій. Показано, що застосування пасивних розпушувачів дозволяє підвищити ефективність сепарації зернових сумішей на 20 % порівняно з відомими способами. Отримані результати можуть бути використані при проєктуванні та модернізації вібропневморешетних сепараторів зерна з метою підвищення їх продуктивності та якості очищення зернового матеріалу
- 5 May 2026
- Published by Publishing House Helvetica (Publications) in Bulletin of Sumy National Agrarian University. The series: Mechanization and Automation of Production Processes
- No. 1,p. 102-109
Open AccessДОСЛІДЖЕННЯ РУХУ ЗЕРНОВОГО МАТЕРІАЛУ В ПРОЦЕСАХ ВІБРОПНЕВМОРЕШЕТНОЇ СЕПАРАЦІЇ
У статті наведено результати теоретичних та експериментальних досліджень руху зернового матеріалу в процесах вібропневморешетної сепарації за умов коливального руху робочої поверхні. Об’єктом дослідження є зерновий матеріал, що перебуває у віброзрідженому стані на решеті вібропневмосепаратора, оснащеного додатковими пасивними робочими органами у вигляді розпушувачів. Актуальність роботи зумовлена обмеженою продуктивністю сучасних вібропневморешетних сепараторів, яка пов’язана з недостатньою інтенсивністю розпушення зернового шару та нерівномірним перерозподілом частинок за висотою шару. Метою дослідження є встановлення закономірностей переміщення та занурення частинок зерна у шарі матеріалу, а також обґрунтування раціональних конструктивних параметрів пасивних розпушувачів, які забезпечують інтенсифікацію процесу сепарації та підвищення його ефективності. У роботі застосовано комплексний підхід, що поєднує аналітичне моделювання і експериментальні дослідження. Побудовано механіко-математичну модель руху окремої частинки зерна у віброзрідженому шарі з урахуванням дії сил гравітації, інерції, напруженого стану сипкого середовища та додаткової виштовхуючої сили, зумовленої взаємодією зернового шару з пасивними розпушувачами. На основі отриманих рівнянь визначено аналітичні залежності, що описують траєкторії руху частинок зерна вздовж робочої поверхні решета, а також у напрямку їх занурення до просіювальних отворів. Проведено графічну інтерпретацію характеру переміщення частинок, яка підтверджує інтенсифікацію рекомбінації зернового матеріалу за висотою шару при використанні додаткових пасивних робочих органів. Експериментальні дослідження виконано на спеціально розробленій вібропневмосепарувальній установці з варіюванням конструктивних параметрів пасивних розпушувачів. Установлено, що раціональні значення ширини полки та кута розхилу розпушувачів сприяють активному розпушенню зернового шару, формуванню каналів у сипкому середовищі та більш інтенсивному просіюванню дрібних фракцій. Показано, що застосування пасивних розпушувачів дозволяє підвищити ефективність сепарації зернових сумішей на 20 % порівняно з відомими способами. Отримані результати можуть бути використані при проєктуванні та модернізації вібропневморешетних сепараторів зерна з метою підвищення їх продуктивності та якості очищення зернового матеріалу
- Open Access
- 29 April 2026
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 13 (1) , G20
Pattern Identification and Modeling of Energy-Efficient Operating Modes in Grain Micronization
The article addresses the critical issue of improving the energy efficiency of grain processing using thermo-radiation micronization. The research aims to substantiate energy-efficient processing modes that ensure increased equipment productivity while simultaneously reducing specific energy consumption. To achieve this goal, an improved mathematical model that describes complex heat and moisture transfer processes in grain during intensive infrared (IR) irradiation was developed. Based on direct experimental data, the model’s parameters were identified, enabling adaptation to real-world production conditions. The article proposes a simplified mathematical description of the patterns of raw material heating and dehydration suitable for engineering calculations. Special attention was paid to the analysis and modeling of oscillating modes, which involved alternating IR irradiation with periods of grain cooling by airflow. It was also demonstrated that such an approach allows for intensifying moisture removal without overheating the product. The research results provide a basis for implementing the oscillating mode as cyclic-pulse irradiation with intermediate forced cooling. This approach is the most effective, as it ensures moisture removal with 20–30 % less energy consumption and reduces surface overheating compared to continuous IR irradiation.
- 29 April 2026
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 13 (1) , G20
Open AccessPattern Identification and Modeling of Energy-Efficient Operating Modes in Grain Micronization
The article addresses the critical issue of improving the energy efficiency of grain processing using thermo-radiation micronization. The research aims to substantiate energy-efficient processing modes that ensure increased equipment productivity while simultaneously reducing specific energy consumption. To achieve this goal, an improved mathematical model that describes complex heat and moisture transfer processes in grain during intensive infrared (IR) irradiation was developed. Based on direct experimental data, the model’s parameters were identified, enabling adaptation to real-world production conditions. The article proposes a simplified mathematical description of the patterns of raw material heating and dehydration suitable for engineering calculations. Special attention was paid to the analysis and modeling of oscillating modes, which involved alternating IR irradiation with periods of grain cooling by airflow. It was also demonstrated that such an approach allows for intensifying moisture removal without overheating the product. The research results provide a basis for implementing the oscillating mode as cyclic-pulse irradiation with intermediate forced cooling. This approach is the most effective, as it ensures moisture removal with 20–30 % less energy consumption and reduces surface overheating compared to continuous IR irradiation.
- Open Access
- 17 April 2026
- Published by Vinnytsia National Agrarian University in Vibrations in engineering and technology
- p. 141
MATHEMATICAL MODELING OF THE VIBRO-CENTRIFUGAL PROCESS OF GRAIN SEPARATION
This article addresses an important scientific and practical problem in agricultural engineering: the intensification of grain cleaning and sorting processes through the use of vibrating centrifugal force fields. It has been established that traditional separation methods often fail to meet the necessary quality standards due to slight differences in the physical and mechanical properties of the components of the grain mixture. The study demonstrates that combining centrifugal fields with axial oscillations of the working surface effectively amplifies differences in particle density and aerodynamic properties, leading to more accurate separation. The study presents an improved mathematical model of the mechanics of a single particle on the inner surface of a conical rotor performing both rotational and oscillatory motion. A comprehensive force analysis was conducted, taking into account the centrifugal inertial force, the oscillatory inertial force, the gravitational force, the normal reaction of the rotor surface, and the friction force between the particle and the material. Based on an analysis of dynamic equilibrium and the conditions of continuous contact motion, a differential equation for the particle’s displacement to the end of the rotor’s expansion was derived. Analytical expressions were derived for determining the instantaneous and average velocities of grain material as functions of the oscillation phase. The study identified the critical conditions necessary to ensure a steady-state motion regime with periodic stops, which is optimal for high-quality separation. The quantitative influence of key kinematic parameters, in particular specifically, the amplitude and frequency of oscillations, the angular velocity of the rotor, the taper angle, and the friction coefficient, on process performance was established. The formulated recommendations provide a rigorous scientific basis for the design and modernization of high-performance vibrocentrifugal machines for grain cleaning, aimed at improving seed quality while simultaneously reducing energy consumption during post-harvest processing stages.
- 17 April 2026
- Published by Vinnytsia National Agrarian University in Vibrations in engineering and technology
- p. 141
Open AccessMATHEMATICAL MODELING OF THE VIBRO-CENTRIFUGAL PROCESS OF GRAIN SEPARATION
This article addresses an important scientific and practical problem in agricultural engineering: the intensification of grain cleaning and sorting processes through the use of vibrating centrifugal force fields. It has been established that traditional separation methods often fail to meet the necessary quality standards due to slight differences in the physical and mechanical properties of the components of the grain mixture. The study demonstrates that combining centrifugal fields with axial oscillations of the working surface effectively amplifies differences in particle density and aerodynamic properties, leading to more accurate separation. The study presents an improved mathematical model of the mechanics of a single particle on the inner surface of a conical rotor performing both rotational and oscillatory motion. A comprehensive force analysis was conducted, taking into account the centrifugal inertial force, the oscillatory inertial force, the gravitational force, the normal reaction of the rotor surface, and the friction force between the particle and the material. Based on an analysis of dynamic equilibrium and the conditions of continuous contact motion, a differential equation for the particle’s displacement to the end of the rotor’s expansion was derived. Analytical expressions were derived for determining the instantaneous and average velocities of grain material as functions of the oscillation phase. The study identified the critical conditions necessary to ensure a steady-state motion regime with periodic stops, which is optimal for high-quality separation. The quantitative influence of key kinematic parameters, in particular specifically, the amplitude and frequency of oscillations, the angular velocity of the rotor, the taper angle, and the friction coefficient, on process performance was established. The formulated recommendations provide a rigorous scientific basis for the design and modernization of high-performance vibrocentrifugal machines for grain cleaning, aimed at improving seed quality while simultaneously reducing energy consumption during post-harvest processing stages.
- Open Access
- 17 April 2026
- Published by Vinnytsia National Agrarian University in Engineering, Energy, Transport AIC
- p. 131
http://tetapk.vsau.org/en/particles/study-of-grain-material-motion-in-a-vibro-centrifugal-separator-considering-kinematic-parameters
The article investigates the influence of kinematic parameters on the velocity of grain material movement along the working surface of the rotor in a vibro-centrifugal separator. The relevance of the study is determined by the need to increase the efficiency of cleaning and sorting processes of grain mixtures through the use of centrifugal and vibration fields, which enhance the differences between particles in terms of specific mass and aerodynamic properties. The paper examines the mechanics of motion of an individual grain particle on the surface of a conical rotor performing simultaneous rotational and vibrational motion. The main forces acting on the particle during its movement are determined, including the centrifugal inertial force, the inertial force caused by vibrational motion, the gravitational force, the reaction force of the rotor surface, and the friction force between the particle and the working surface. Based on the analysis of the conditions for continuous contact motion of a particle along the rotor surface, a differential equation describing its motion was obtained, and relationships for determining the displacement and velocity of grain particles depending on the vibration phase were derived. The conditions ensuring stable particle motion in the direction of expansion of the conical rotor with periodic stops were established. An analytical expression for determining the average velocity of grain material movement was obtained, taking into account the vibration amplitude and frequency, the angular velocity of rotor rotation, the cone angle of the working body, and the coefficient of friction between the material and the rotor surface. The theoretical studies were supplemented by experimental investigations carried out on laboratory and pilot experimental installations, where the influence of rotor rotational speed, grain feed rate, and air flow parameters on the separation efficiency was analyzed. It was established that an increase in the vibration amplitude and frequency, as well as in the angular velocity of the rotor, leads to an increase in the average velocity of grain particle movement along the working surface. The obtained results can be used to substantiate the design and operating parameters of vibro-centrifugal separators and to develop high-performance grain cleaning machines.
- 17 April 2026
- Published by Vinnytsia National Agrarian University in Engineering, Energy, Transport AIC
- p. 131
Open Accesshttp://tetapk.vsau.org/en/particles/study-of-grain-material-motion-in-a-vibro-centrifugal-separator-considering-kinematic-parameters
The article investigates the influence of kinematic parameters on the velocity of grain material movement along the working surface of the rotor in a vibro-centrifugal separator. The relevance of the study is determined by the need to increase the efficiency of cleaning and sorting processes of grain mixtures through the use of centrifugal and vibration fields, which enhance the differences between particles in terms of specific mass and aerodynamic properties. The paper examines the mechanics of motion of an individual grain particle on the surface of a conical rotor performing simultaneous rotational and vibrational motion. The main forces acting on the particle during its movement are determined, including the centrifugal inertial force, the inertial force caused by vibrational motion, the gravitational force, the reaction force of the rotor surface, and the friction force between the particle and the working surface. Based on the analysis of the conditions for continuous contact motion of a particle along the rotor surface, a differential equation describing its motion was obtained, and relationships for determining the displacement and velocity of grain particles depending on the vibration phase were derived. The conditions ensuring stable particle motion in the direction of expansion of the conical rotor with periodic stops were established. An analytical expression for determining the average velocity of grain material movement was obtained, taking into account the vibration amplitude and frequency, the angular velocity of rotor rotation, the cone angle of the working body, and the coefficient of friction between the material and the rotor surface. The theoretical studies were supplemented by experimental investigations carried out on laboratory and pilot experimental installations, where the influence of rotor rotational speed, grain feed rate, and air flow parameters on the separation efficiency was analyzed. It was established that an increase in the vibration amplitude and frequency, as well as in the angular velocity of the rotor, leads to an increase in the average velocity of grain particle movement along the working surface. The obtained results can be used to substantiate the design and operating parameters of vibro-centrifugal separators and to develop high-performance grain cleaning machines.
- 23 December 2025
- Published by Central Ukrainian National Technical University in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
- No. 55
Theoretical Justification for the Separation of Grain Material on a Conical Sieve
The purpose of this article is to provide a theoretical justification and scientific basis for the development of a new type of vibro-centrifugal separator with a conical sieve. The study aims to overcome the limitations of existing pneumatic separators and to combine the advantages of pneumatic and sieve separation methods in order to improve the efficiency and quality of grain cleaning during post-harvest processing. The article considers theoretical aspects of improving post-harvest grain processing through the application of combined separation methods. The current state of pneumatic separators is analyzed, which mainly ensure the removal of light impurities, whereas for extracting heavy fractions and subsequent cleaning, sieve machines are required. Such an approach necessitates additional equipment, complicates technological schemes, and reduces the overall efficiency of production. Therefore, a scientific task is formulated to design a fundamentally new type of separator that combines the advantages of both methods, providing effective division of grain mass into fractions according to their physical and mechanical properties. A design of a vibro-centrifugal separator with a conical working surface is proposed, which enables the division of grain mixtures based on differences in particle terminal velocity. A mathematical model of particle motion on the conical sieve is developed, taking into account the action of centrifugal force, air drag, gravity, and the angle of air flow supply. Based on the derived motion equations, the conditions for particle displacement along the cone generatrix are determined, which allowed the formulation of a criterion for assigning particles to different fractions. The developed theoretical model provides a more accurate prediction of the separation process by considering both the structural parameters of the equipment and the physical properties of the grain. As a result of the study, three main separation zones were identified: for heavy, main, and fine fractions, which confirms the effectiveness of the proposed separator design. The obtained results demonstrate the prospects of using a conical sieve in vibro-centrifugal machines and can serve as a foundation for further experimental research. The practical significance of this work lies in the creation of a scientifically grounded basis for developing high-performance separators of a new generation, capable of improving the quality of post-harvest grain cleaning and optimizing technological processes in agricultural production.
- 23 December 2025
- Published by Central Ukrainian National Technical University in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
- No. 55
Theoretical Justification for the Separation of Grain Material on a Conical Sieve
The purpose of this article is to provide a theoretical justification and scientific basis for the development of a new type of vibro-centrifugal separator with a conical sieve. The study aims to overcome the limitations of existing pneumatic separators and to combine the advantages of pneumatic and sieve separation methods in order to improve the efficiency and quality of grain cleaning during post-harvest processing. The article considers theoretical aspects of improving post-harvest grain processing through the application of combined separation methods. The current state of pneumatic separators is analyzed, which mainly ensure the removal of light impurities, whereas for extracting heavy fractions and subsequent cleaning, sieve machines are required. Such an approach necessitates additional equipment, complicates technological schemes, and reduces the overall efficiency of production. Therefore, a scientific task is formulated to design a fundamentally new type of separator that combines the advantages of both methods, providing effective division of grain mass into fractions according to their physical and mechanical properties. A design of a vibro-centrifugal separator with a conical working surface is proposed, which enables the division of grain mixtures based on differences in particle terminal velocity. A mathematical model of particle motion on the conical sieve is developed, taking into account the action of centrifugal force, air drag, gravity, and the angle of air flow supply. Based on the derived motion equations, the conditions for particle displacement along the cone generatrix are determined, which allowed the formulation of a criterion for assigning particles to different fractions. The developed theoretical model provides a more accurate prediction of the separation process by considering both the structural parameters of the equipment and the physical properties of the grain. As a result of the study, three main separation zones were identified: for heavy, main, and fine fractions, which confirms the effectiveness of the proposed separator design. The obtained results demonstrate the prospects of using a conical sieve in vibro-centrifugal machines and can serve as a foundation for further experimental research. The practical significance of this work lies in the creation of a scientifically grounded basis for developing high-performance separators of a new generation, capable of improving the quality of post-harvest grain cleaning and optimizing technological processes in agricultural production.
- 2 November 2025
- Published by National Scientific Center - Institute of Agricultural Engineering and Electrification in Mechanics and automatics of agroindustrial production
Prospects for the application of the YOLOv11 model for automatic control of combine harvesters based on the detection of damaged grains
Purpose. Improving the efficiency of grain harvesting by developing scientific and technical principles for an automatic combine harvester control system based on the YOLOv11 model, which minimizes grain damage losses through high-precision real-time detection. Methods. Methods of data analysis, collection and preparation, digital image segmentation, deep learning of convolutional neural networks were used. Software for digital image analysis was developed in the Python programming language using the computer vision libraries OpenCV and PyTorch. Results. The concept and algorithm of the automation system for the control of a combine harvester were developed. The influence of the parameters of the working bodies of the combine harvester on grain injury was studied. A dataset was collected and the YOLOv11 model was trained for the classification and segmentation of winter wheat grain material. The trained model was tested by detecting objects and segmenting them on images of real samples of grain materials. Conclusions. The research confirms that the implementation of an automatic control system for combine harvesters based on object detection is not only technically feasible, but also economically viable. The problem of grain damage, which leads to significant financial losses, can be solved using technologies capable of providing constant and accurate quality control in real time. The YOLOv11 model, due to its speed and architectural innovations, meets the requirements necessary for dynamic control of a combine harvester. In addition, its architecture, specially designed for improved detection of small and partially hidden objects, solves key challenges in visual analysis of grain material flows. The conceptual model of the system, based on peripheral computing, can operate autonomously in field conditions, making it independent of the network infrastructure. Testing of the model demonstrated a high level of detection of grain mixture objects. According to the results of testing on the Jetson AGX Orin GPU, the processing time for a 1280x1280 image was 90.6 ms. Keywords: winter wheat, combine harvester, convolutional neural network, machine vision.
- 2 November 2025
- Published by National Scientific Center - Institute of Agricultural Engineering and Electrification in Mechanics and automatics of agroindustrial production
Prospects for the application of the YOLOv11 model for automatic control of combine harvesters based on the detection of damaged grains
Purpose. Improving the efficiency of grain harvesting by developing scientific and technical principles for an automatic combine harvester control system based on the YOLOv11 model, which minimizes grain damage losses through high-precision real-time detection. Methods. Methods of data analysis, collection and preparation, digital image segmentation, deep learning of convolutional neural networks were used. Software for digital image analysis was developed in the Python programming language using the computer vision libraries OpenCV and PyTorch. Results. The concept and algorithm of the automation system for the control of a combine harvester were developed. The influence of the parameters of the working bodies of the combine harvester on grain injury was studied. A dataset was collected and the YOLOv11 model was trained for the classification and segmentation of winter wheat grain material. The trained model was tested by detecting objects and segmenting them on images of real samples of grain materials. Conclusions. The research confirms that the implementation of an automatic control system for combine harvesters based on object detection is not only technically feasible, but also economically viable. The problem of grain damage, which leads to significant financial losses, can be solved using technologies capable of providing constant and accurate quality control in real time. The YOLOv11 model, due to its speed and architectural innovations, meets the requirements necessary for dynamic control of a combine harvester. In addition, its architecture, specially designed for improved detection of small and partially hidden objects, solves key challenges in visual analysis of grain material flows. The conceptual model of the system, based on peripheral computing, can operate autonomously in field conditions, making it independent of the network infrastructure. Testing of the model demonstrated a high level of detection of grain mixture objects. According to the results of testing on the Jetson AGX Orin GPU, the processing time for a 1280x1280 image was 90.6 ms. Keywords: winter wheat, combine harvester, convolutional neural network, machine vision.