Wenhe Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wenhe Feng has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Jiang Guo
State Key Laboratory of High-Performance Precision Manufacturing, Dalian University of Technology, Dalian, China
2 shared publications Yin Chi Wan
Singapore Institute of Manufacturing Technology (SIMTech), Singapore, Singapore
2 shared publicationsChaolin Tan
1 shared publicationFei Weng
Singapore Institute of Manufacturing Technology (SIMTech), Agency for Science, Technology and Research (A*STAR) Research Entities, Singapore, Singapore
1 shared publicationGavin Kane O’nEill
Division of Musculoskeletal Trauma, Department of Orthopaedic Surgery, NUHS Tower Block Level 11, National University Hospital, Singapore, Singapore
1 shared publication- Guijun Bi
Institute of Intelligent Manufacturing, Guangdong Academy of Sciences, Guangzhou, China
1 shared publication
Latest Publications
- Top Cited Papers
- 22 April 2024
- Published by Elsevier in Journal of Manufacturing Systems
- Vol. 74, 527-574
In-situ process monitoring and adaptive quality enhancement in laser additive manufacturing: A critical review
- 22 April 2024
- Published by Elsevier in Journal of Manufacturing Systems
- Vol. 74, 527-574
Top Cited PapersIn-situ process monitoring and adaptive quality enhancement in laser additive manufacturing: A critical review
- 10 December 2022
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 8 (5) , 997-1005
The influence of laser surface remelting on the in vitro cell viability of additively manufactured Ti–6Al–4V plates
- 10 December 2022
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 8 (5) , 997-1005
The influence of laser surface remelting on the in vitro cell viability of additively manufactured Ti–6Al–4V plates
- 24 July 2020
- Published by Springer Nature in Nanomanufacturing and Metrology
- Vol. 3 (3) , 199-204
PMMA-Based Microsphere Mask for Sub-wavelength Photolithography
- 24 July 2020
- Published by Springer Nature in Nanomanufacturing and Metrology
- Vol. 3 (3) , 199-204
PMMA-Based Microsphere Mask for Sub-wavelength Photolithography
- 6 March 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (4) , 045011
Underwater laser micro-milling of fine-grained aluminium and the process modelling by machine learning
Nanosecond-pulsed laser ablation is often accompanied by adverse thermal effects, such as oxidation, debris recast and burr formation. To reduce these effects, in this paper, the authors present the underwater laser milling process using RSA-905 fine-grained aluminium as the target material for the first time. The results show that channels up to 200 μ m in width, 700 μ m depth and bottom roughness around 1 µ m R a could be fabricated with reduced thermal effects. By conducting multi- and single-factor experiments, empirical models relating the laser processing parameters to the key dimensions of channels were derived using an artificial neural network algorithm and polynomial regression, and the models’ accuracies were evaluated. Based on the models, the cross-section profile of a channel subject to a given set of processing parameters can be predicted. The process can serve as a pre-treatment technique in mechanical milling such that the tool life will be extended and the profile of a desired feature can be precisely defined.
- 6 March 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (4) , 045011
Underwater laser micro-milling of fine-grained aluminium and the process modelling by machine learning
Nanosecond-pulsed laser ablation is often accompanied by adverse thermal effects, such as oxidation, debris recast and burr formation. To reduce these effects, in this paper, the authors present the underwater laser milling process using RSA-905 fine-grained aluminium as the target material for the first time. The results show that channels up to 200 μ m in width, 700 μ m depth and bottom roughness around 1 µ m R a could be fabricated with reduced thermal effects. By conducting multi- and single-factor experiments, empirical models relating the laser processing parameters to the key dimensions of channels were derived using an artificial neural network algorithm and polynomial regression, and the models’ accuracies were evaluated. Based on the models, the cross-section profile of a channel subject to a given set of processing parameters can be predicted. The process can serve as a pre-treatment technique in mechanical milling such that the tool life will be extended and the profile of a desired feature can be precisely defined.
- 1 April 2019
- Published by Elsevier in Optics & Laser Technology
- Vol. 111, 653-663
Deep channel fabrication on copper by multi-scan underwater laser machining
- 1 April 2019
- Published by Elsevier in Optics & Laser Technology
- Vol. 111, 653-663
Deep channel fabrication on copper by multi-scan underwater laser machining