Sang-Dae Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sang-Dae Lee has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Yong-Joo Kim
Eco-Friendly Hydrogen Electric Tractor & Agricultural Machinery Institute, Chungnam National University, Daejeon 34134, Republic of Korea
7 shared publications - Wan-Soo Kim
Department of Bio-Industrial Machinery Engineering, Kyungpook National University, Daegu, Republic of Korea
6 shared publications - Yeon-Soo Kim
Department of Bio-industrial Machinery Engineering, Pusan National University, Miryang 50463, Republic of Korea
6 shared publications - Bo-Min Bae
Department of Bio-industrial Machinery Engineering, Pusan National University, Miryang 50463, Republic of Korea
3 shared publications - Seung-Min Baek
Eco-Friendly Hydrogen Electric Tractor & Agricultural Machinery Institute, Chungnam National University, Daejeon 34134, Republic of Korea
3 shared publications - Seung-Yun Baek
Department of Smart Agriculture Systems, Chungnam National University, Daejeon 34134, Republic of Korea
3 shared publications
Latest Publications
- 11 February 2026
- Published by Springer Nature in Journal of Biosystems Engineering
- Vol. 51 (1) , 13
DEM Simulation for Selecting Optimal Tillage Depth of Moldboard Plow in Sandy Loam
- 11 February 2026
- Published by Springer Nature in Journal of Biosystems Engineering
- Vol. 51 (1) , 13
DEM Simulation for Selecting Optimal Tillage Depth of Moldboard Plow in Sandy Loam
- Open Access
- 27 November 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (12) , 2205
The Development of a Draft Force Prediction Model for Agricultural Tractors Based on the Discrete Element Method in Loam and Clay Loam
In the field of agricultural machinery, various empirical field tests are conducted to measure design loads for the optimal design and implementation of tractors. However, conducting field tests is costly and time-consuming, with many constraints on weather and field soil conditions, and research utilizing simulations has been proposed as an alternative to overcome these shortcomings. The objective of this study is to develop a DEM-based draft force prediction model that reflects differences in soil properties. For this, soil property measurements were conducted in two fields (Field A in Daejeon, Republic of Korea, and Field B in Chuncheon, Republic of Korea). The measured properties were used as parameters for DEM-based particle modeling. For the interparticle contact model, the EEPA contact model was used to reflect the compressibility and stickiness of cohesive soils. To generate an environment similar to real soil, particle mass and surface energy were calibrated based on bulk density and shear torque. The soil property measurements showed that Field B had a higher shear strength and lower cone index and moisture content compared to Field A. The actual measured draft force was 19.47% higher in Field B than in Field A. In this study, this demonstrates the uncertainty in predicting draft force by correlating only one soil property and suggests the need for a comprehensive consideration of soil properties. The simulation results of the tillage operation demonstrated the accuracy of the predicted shedding force compared to the actual field experiment and the existing theoretical calculation method (ASABE D497.4). Compared to the measured draft force in the actual field test, the predictions were 86.75% accurate in Field A and 74.51% accurate in Field B, which is 84% more accurate in Field A and 37.32% more accurate in Field B than the theoretical calculation method. This result shows that load prediction should reflect the soil properties of the working environment, and is expected to be used as an indicator of soil–tool interaction for digital twin modeling processes in the research field of bio-industrial machinery.
- 27 November 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (12) , 2205
Open AccessThe Development of a Draft Force Prediction Model for Agricultural Tractors Based on the Discrete Element Method in Loam and Clay Loam
In the field of agricultural machinery, various empirical field tests are conducted to measure design loads for the optimal design and implementation of tractors. However, conducting field tests is costly and time-consuming, with many constraints on weather and field soil conditions, and research utilizing simulations has been proposed as an alternative to overcome these shortcomings. The objective of this study is to develop a DEM-based draft force prediction model that reflects differences in soil properties. For this, soil property measurements were conducted in two fields (Field A in Daejeon, Republic of Korea, and Field B in Chuncheon, Republic of Korea). The measured properties were used as parameters for DEM-based particle modeling. For the interparticle contact model, the EEPA contact model was used to reflect the compressibility and stickiness of cohesive soils. To generate an environment similar to real soil, particle mass and surface energy were calibrated based on bulk density and shear torque. The soil property measurements showed that Field B had a higher shear strength and lower cone index and moisture content compared to Field A. The actual measured draft force was 19.47% higher in Field B than in Field A. In this study, this demonstrates the uncertainty in predicting draft force by correlating only one soil property and suggests the need for a comprehensive consideration of soil properties. The simulation results of the tillage operation demonstrated the accuracy of the predicted shedding force compared to the actual field experiment and the existing theoretical calculation method (ASABE D497.4). Compared to the measured draft force in the actual field test, the predictions were 86.75% accurate in Field A and 74.51% accurate in Field B, which is 84% more accurate in Field A and 37.32% more accurate in Field B than the theoretical calculation method. This result shows that load prediction should reflect the soil properties of the working environment, and is expected to be used as an indicator of soil–tool interaction for digital twin modeling processes in the research field of bio-industrial machinery.
- Open Access
- 3 August 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (8) , 1556
Working Load Analysis of a 42 kW Class Agricultural Tractor According to Tillage Type and Gear Selection during Rotary Tillage Operation
The objective of this study was to analyze the effect of tillage type (i.e., primary and secondary tillage) and gear selection (P1L2 to P1L4) on the working load of tractor–implement systems during rotary tillage. Soil properties change with depth, and differences in properties along the depth distribution, such as the location of formation of the hardpan layer, internal friction angle, and moisture content, affect the load of rotary tillage operations. Therefore, the physical properties of soil along the field depth distribution were measured to analyze the effect of tillage type and gear selection on workload in rotary tillage. In addition, a load measurement system equipped with PTO torque meter, axle torque meter, proximity sensor, and RTK-GPS were configured on the 42 kW agricultural tractor. The experimental results show that the combination of tillage type and gear selection has a wide-ranging effect on the tractor’s workload and performance when the rotavator operated at the same tilling depth. Overall working load was higher by up to 14% (engine) and 29.1% (PTO shaft) in primary tillage compared to secondary tillage when the gear selection was the same. When the tillage type is the same, it was analyzed that the overall average torque increased by up to 35.9% (engine) and 33.9% (PTO shaft) in P1L4 compared to P1L2 according to gear selection. Based on load analysis results, it was found that the effect of gear selection (Engine: 4–14%, PTO: 12.1–28.6%) on engine and PTO loads was higher than that of tillage type (Engine: 31.6–35.1%, PTO: 31.9–32.8%), and the power requirement tended to decrease in secondary tillage. Therefore, working load should be considered according to the soil environment and tillage type when designing agricultural machinery system.
- 3 August 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (8) , 1556
Open AccessWorking Load Analysis of a 42 kW Class Agricultural Tractor According to Tillage Type and Gear Selection during Rotary Tillage Operation
The objective of this study was to analyze the effect of tillage type (i.e., primary and secondary tillage) and gear selection (P1L2 to P1L4) on the working load of tractor–implement systems during rotary tillage. Soil properties change with depth, and differences in properties along the depth distribution, such as the location of formation of the hardpan layer, internal friction angle, and moisture content, affect the load of rotary tillage operations. Therefore, the physical properties of soil along the field depth distribution were measured to analyze the effect of tillage type and gear selection on workload in rotary tillage. In addition, a load measurement system equipped with PTO torque meter, axle torque meter, proximity sensor, and RTK-GPS were configured on the 42 kW agricultural tractor. The experimental results show that the combination of tillage type and gear selection has a wide-ranging effect on the tractor’s workload and performance when the rotavator operated at the same tilling depth. Overall working load was higher by up to 14% (engine) and 29.1% (PTO shaft) in primary tillage compared to secondary tillage when the gear selection was the same. When the tillage type is the same, it was analyzed that the overall average torque increased by up to 35.9% (engine) and 33.9% (PTO shaft) in P1L4 compared to P1L2 according to gear selection. Based on load analysis results, it was found that the effect of gear selection (Engine: 4–14%, PTO: 12.1–28.6%) on engine and PTO loads was higher than that of tillage type (Engine: 31.6–35.1%, PTO: 31.9–32.8%), and the power requirement tended to decrease in secondary tillage. Therefore, working load should be considered according to the soil environment and tillage type when designing agricultural machinery system.
- Open Access
- 24 December 2022
- Published by MDPI AG in Agriculture
- Vol. 13 (1) , 56
Optimal Path Generation with Obstacle Avoidance and Subfield Connection for an Autonomous Tractor
As autonomous tractors become more common crop harvesting applications, the need to optimize the global servicing path becomes crucial for maximizing efficiency and crop yield. In recent years, several methods of path generation have been researched, but very few have studied their applications on complex field shapes. In this study, a method of creating the optimal servicing path for simple and complex field shapes is proposed. The proposed algorithm creates subfields for a target land, optimizes the track direction for several subfields individually, merges subfields that result in overall increased efficiency, and finds the minimum non-operating paths to travel from subfield to subfield while selecting the respective optimal subfield starting locations. Additionally, it is required that this process must be done within 3 seconds to meet performance requirements. Results from 3 separate field shapes show that the field traversal efficiency can range from 68.0% to 94.4%, and the coverage ratio can range from 98.8% to 99.9% for several different conditions. In comparison with previous studies using the same field shape, the proposed methods demonstrate an increase of 5.5% in field traversal efficiency.
- 24 December 2022
- Published by MDPI AG in Agriculture
- Vol. 13 (1) , 56
Open AccessOptimal Path Generation with Obstacle Avoidance and Subfield Connection for an Autonomous Tractor
As autonomous tractors become more common crop harvesting applications, the need to optimize the global servicing path becomes crucial for maximizing efficiency and crop yield. In recent years, several methods of path generation have been researched, but very few have studied their applications on complex field shapes. In this study, a method of creating the optimal servicing path for simple and complex field shapes is proposed. The proposed algorithm creates subfields for a target land, optimizes the track direction for several subfields individually, merges subfields that result in overall increased efficiency, and finds the minimum non-operating paths to travel from subfield to subfield while selecting the respective optimal subfield starting locations. Additionally, it is required that this process must be done within 3 seconds to meet performance requirements. Results from 3 separate field shapes show that the field traversal efficiency can range from 68.0% to 94.4%, and the coverage ratio can range from 98.8% to 99.9% for several different conditions. In comparison with previous studies using the same field shape, the proposed methods demonstrate an increase of 5.5% in field traversal efficiency.
- Open Access
Analysis of the Effect of Tillage Depth on the Working Performance of Tractor-Moldboard Plow System under Various Field Environments
The purpose of this study was to analyze the tillage depth effect on the tractor-moldboard plow systems in various soil environments and tillage depths using a field load measurement system. A field load measurement system can measure the engine load, draft force, travel speed, wheel axle load, and tillage depth in real-time. In addition, measurement tests of soil properties in the soil layer were preceded to analyze the effect of field environments. The presented results show that moldboard plow at the same tillage depth had a wide range of influences on the tractor’s working load and performance under various environments. As the draft force due to soil–tool interaction occurred in the range of 5.6–17.7 kN depending on the field environment, the overall mean engine torque and rear axle torque were up to 2.14 times and 1.67 times higher in hard and clayey soil, respectively, than in soft soil environments. In addition, the results showed tractive efficiency of 0.56–0.73 and were analyzed to have a lugging ability of 67.8% with a 44% maximum torque rise. The engine power requirement in hardpan was similar within 3.6–9.6%, but the power demand of the rear axle differed by up to 18.4%.
Open AccessAnalysis of the Effect of Tillage Depth on the Working Performance of Tractor-Moldboard Plow System under Various Field Environments
The purpose of this study was to analyze the tillage depth effect on the tractor-moldboard plow systems in various soil environments and tillage depths using a field load measurement system. A field load measurement system can measure the engine load, draft force, travel speed, wheel axle load, and tillage depth in real-time. In addition, measurement tests of soil properties in the soil layer were preceded to analyze the effect of field environments. The presented results show that moldboard plow at the same tillage depth had a wide range of influences on the tractor’s working load and performance under various environments. As the draft force due to soil–tool interaction occurred in the range of 5.6–17.7 kN depending on the field environment, the overall mean engine torque and rear axle torque were up to 2.14 times and 1.67 times higher in hard and clayey soil, respectively, than in soft soil environments. In addition, the results showed tractive efficiency of 0.56–0.73 and were analyzed to have a lugging ability of 67.8% with a 44% maximum torque rise. The engine power requirement in hardpan was similar within 3.6–9.6%, but the power demand of the rear axle differed by up to 18.4%.
- Open Access
Power Transmission Efficiency Analysis of 42 kW Power Agricultural Tractor According to Tillage Depth during Moldboard Plowing
In order to optimize tractor design and optimize efficiency during tillage operation, it is essential to verify the impact through field tests on factors affecting the tractor load. The objectives of this study were to investigate the effect of tillage depth on power transmission efficiency of 42 kW power agricultural tractor during moldboard plowing. A load measurement system and a tillage depth measurement system were configured for field tests. To analyze the effect of tillage depth on power transmission efficiency and fuel consumption, the data measured in the three-repeated field test were classified according to tillage depth. As the tillage depth increased from 11 cm at the top of the hardpan to 23 cm at the deepest, the required power of the engine increased by approximately 13% from 35.48 kW to 40.11 kW, and the power transmission efficiency also increased significantly from 66% to 95%. Among them, the power transmission efficiency of the rear axle was significantly increased from 38% to 59%, which was the most affected. As the tillage depth increased, the overall power requirement is greatly increased due to the resulting workload, but the fuel consumption and the specific fuel consumption are reduced because the engine speed of the tractor is reduced. As the tillage depth increased from 11 cm to 23 cm, the fuel consumption rate was rather reduced by 13.5% as the engine rotational speed decreased 11.3% due to the increase work load of tractor. In addition, the specific fuel consumption decreased from 302.44 g/kWh to 236.93 g/kWh, showing a fuel consumption saving of up to 21.7% during moldboard plow. In addition, as the tillage depth increased, the ratio of the value excluding the mechanical and hydraulic power requirements has significantly decreased from 34% to 5% as the power transmission efficiency increases. This study considers the soil properties according to the soil depth, as well as the power transmission efficiency and fuel consumption rate. The research results can provide useful information for research on power transmission efficiency and selection of an appropriate power source of agricultural tractor according to tillage depth during moldboard plowing and are expected to be used in various ways as basic studies of digital farming research in agricultural machinery.
Open AccessPower Transmission Efficiency Analysis of 42 kW Power Agricultural Tractor According to Tillage Depth during Moldboard Plowing
In order to optimize tractor design and optimize efficiency during tillage operation, it is essential to verify the impact through field tests on factors affecting the tractor load. The objectives of this study were to investigate the effect of tillage depth on power transmission efficiency of 42 kW power agricultural tractor during moldboard plowing. A load measurement system and a tillage depth measurement system were configured for field tests. To analyze the effect of tillage depth on power transmission efficiency and fuel consumption, the data measured in the three-repeated field test were classified according to tillage depth. As the tillage depth increased from 11 cm at the top of the hardpan to 23 cm at the deepest, the required power of the engine increased by approximately 13% from 35.48 kW to 40.11 kW, and the power transmission efficiency also increased significantly from 66% to 95%. Among them, the power transmission efficiency of the rear axle was significantly increased from 38% to 59%, which was the most affected. As the tillage depth increased, the overall power requirement is greatly increased due to the resulting workload, but the fuel consumption and the specific fuel consumption are reduced because the engine speed of the tractor is reduced. As the tillage depth increased from 11 cm to 23 cm, the fuel consumption rate was rather reduced by 13.5% as the engine rotational speed decreased 11.3% due to the increase work load of tractor. In addition, the specific fuel consumption decreased from 302.44 g/kWh to 236.93 g/kWh, showing a fuel consumption saving of up to 21.7% during moldboard plow. In addition, as the tillage depth increased, the ratio of the value excluding the mechanical and hydraulic power requirements has significantly decreased from 34% to 5% as the power transmission efficiency increases. This study considers the soil properties according to the soil depth, as well as the power transmission efficiency and fuel consumption rate. The research results can provide useful information for research on power transmission efficiency and selection of an appropriate power source of agricultural tractor according to tillage depth during moldboard plowing and are expected to be used in various ways as basic studies of digital farming research in agricultural machinery.
- Open Access
Analysis of Tillage Depth and Gear Selection for Mechanical Load and Fuel Efficiency of an Agricultural Tractor Using an Agricultural Field Measuring System
This study was conducted to analyze the effects of tillage depth and gear selection on the mechanical load and fuel efficiency of an agricultural tractor during plow tillage. In order to analyze these effects, we developed an agricultural field measuring system consisting of a load measurement part (wheel torque meter, proximity sensor, and real-time kinematic (RTK) global positioning system (GPS)) and a tillage depth measurement part (linear potentiometer and inclinometer). Field tests were carried out using moldboard plows with a maximum tillage depth of 20 cm and three gear selections (M2H, M3L, and M3H) in a rice stubble paddy field for plow tillage. The average travel speed and slip ratio had the lowest M2H and the highest M3L. M3H had the highest theoretical speed, but the travel speed was 0.13 km/h lower than M3L due to the reduction in the axle rotational speed at deep tillage depth. Regarding engine load, the higher the gear, the greater the torque and the lower the axle rotation speed. The front axle load was not significantly affected by the tillage depth as compared to other mechanical parts, except for the M3H gear. The rear axle load generated about twice the torque of the front wheel and overall, it tended to show a higher average rear axle torque at higher gear selection. The rear axle load and fuel rate were found to be most affected by the combination of the tillage depth and gear selection combination. Overall, field test results show that the M3H had the highest fuel efficiency and a high working speed while overcoming high loads at the same tillage depth. In conclusion, M3H is the most suitable gear stage for plow cultivation, and the higher the gear stage and the deeper the tillage depth during plowing, the higher the fuel efficiency. The results of this study will be useful for analyzing mechanical load and fuel efficiency during farm operations. In a future study, we will conduct load analysis studies in other farming operations that consider various soil mechanics factors as well as tillage depths and gear selections.
Open AccessAnalysis of Tillage Depth and Gear Selection for Mechanical Load and Fuel Efficiency of an Agricultural Tractor Using an Agricultural Field Measuring System
This study was conducted to analyze the effects of tillage depth and gear selection on the mechanical load and fuel efficiency of an agricultural tractor during plow tillage. In order to analyze these effects, we developed an agricultural field measuring system consisting of a load measurement part (wheel torque meter, proximity sensor, and real-time kinematic (RTK) global positioning system (GPS)) and a tillage depth measurement part (linear potentiometer and inclinometer). Field tests were carried out using moldboard plows with a maximum tillage depth of 20 cm and three gear selections (M2H, M3L, and M3H) in a rice stubble paddy field for plow tillage. The average travel speed and slip ratio had the lowest M2H and the highest M3L. M3H had the highest theoretical speed, but the travel speed was 0.13 km/h lower than M3L due to the reduction in the axle rotational speed at deep tillage depth. Regarding engine load, the higher the gear, the greater the torque and the lower the axle rotation speed. The front axle load was not significantly affected by the tillage depth as compared to other mechanical parts, except for the M3H gear. The rear axle load generated about twice the torque of the front wheel and overall, it tended to show a higher average rear axle torque at higher gear selection. The rear axle load and fuel rate were found to be most affected by the combination of the tillage depth and gear selection combination. Overall, field test results show that the M3H had the highest fuel efficiency and a high working speed while overcoming high loads at the same tillage depth. In conclusion, M3H is the most suitable gear stage for plow cultivation, and the higher the gear stage and the deeper the tillage depth during plowing, the higher the fuel efficiency. The results of this study will be useful for analyzing mechanical load and fuel efficiency during farm operations. In a future study, we will conduct load analysis studies in other farming operations that consider various soil mechanics factors as well as tillage depths and gear selections.
- Open Access
Development of a Real-Time Tillage Depth Measurement System for Agricultural Tractors: Application to the Effect Analysis of Tillage Depth on Draft Force during Plow Tillage
The objectives of this study were to develop a real-time tillage depth measurement system for agricultural tractor performance analysis and then to validate these configured systems through soil non-penetration tests and field experiment during plow tillage. The real-time tillage depth measurement system was developed by using a sensor fusion method, consisting of a linear potentiometer, inclinometer, and optical distance sensor to measure the vertical penetration depth of the attached implement. In addition, a draft force measurement system was developed using six-component load cells, and an accuracy of 98.9% was verified through a static load test. As a result of the soil non-penetration tests, it was confirmed that sensor fusion type A, consisting of a linear potentiometer and inclinometer, was 6.34–11.76% more accurate than sensor fusion type B, consisting of an optical distance sensor and inclinometer. Therefore, sensor fusion type A was used during field testing as it was found to be more suitable for use in severe working environments. To verify the accuracy of the real-time tillage depth measurement system, a linear regression analysis was performed between the measured draft and the predicted values calculated using the American Society of Agricultural and Biological Engineers (ASABE) standards-based equation. Experimental data such as traveling speed and draft force showed that it was significantly affected by tillage depth, and the coefficient of determination value at M3–Low was 0.847, which is relatively higher than M3–High. In addition, the regression analysis of the integrated data showed an R-square value of 0.715, which is an improvement compared to the accuracy of the ASABE standard prediction formula. In conclusion, the effect of tillage depth on draft force of agricultural tractors during plow tillage was analyzed by the simultaneous operation of the proposed real-time tillage depth measurement system and draft force measurement system. In addition, system accuracy is higher than the predicted accuracy of 40% based on the ASABE standard equation, which is considered to be useful for various agricultural machinery research fields. In future studies, real-time tillage depth measurement systems can be used in tractor power train design and to ensure component reliability, in accordance with agricultural working conditions, by predicting draft force and axle loads depending on the tillage depth during tillage operations.Open AccessDevelopment of a Real-Time Tillage Depth Measurement System for Agricultural Tractors: Application to the Effect Analysis of Tillage Depth on Draft Force during Plow Tillage
The objectives of this study were to develop a real-time tillage depth measurement system for agricultural tractor performance analysis and then to validate these configured systems through soil non-penetration tests and field experiment during plow tillage. The real-time tillage depth measurement system was developed by using a sensor fusion method, consisting of a linear potentiometer, inclinometer, and optical distance sensor to measure the vertical penetration depth of the attached implement. In addition, a draft force measurement system was developed using six-component load cells, and an accuracy of 98.9% was verified through a static load test. As a result of the soil non-penetration tests, it was confirmed that sensor fusion type A, consisting of a linear potentiometer and inclinometer, was 6.34–11.76% more accurate than sensor fusion type B, consisting of an optical distance sensor and inclinometer. Therefore, sensor fusion type A was used during field testing as it was found to be more suitable for use in severe working environments. To verify the accuracy of the real-time tillage depth measurement system, a linear regression analysis was performed between the measured draft and the predicted values calculated using the American Society of Agricultural and Biological Engineers (ASABE) standards-based equation. Experimental data such as traveling speed and draft force showed that it was significantly affected by tillage depth, and the coefficient of determination value at M3–Low was 0.847, which is relatively higher than M3–High. In addition, the regression analysis of the integrated data showed an R-square value of 0.715, which is an improvement compared to the accuracy of the ASABE standard prediction formula. In conclusion, the effect of tillage depth on draft force of agricultural tractors during plow tillage was analyzed by the simultaneous operation of the proposed real-time tillage depth measurement system and draft force measurement system. In addition, system accuracy is higher than the predicted accuracy of 40% based on the ASABE standard equation, which is considered to be useful for various agricultural machinery research fields. In future studies, real-time tillage depth measurement systems can be used in tractor power train design and to ensure component reliability, in accordance with agricultural working conditions, by predicting draft force and axle loads depending on the tillage depth during tillage operations.