I.-Chen Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
I.-Chen Chen has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
Jenq-Yang Chang
5 shared publicationsYen-Ho Chu
5 shared publicationsTeng-Hsiang Chang
4 shared publicationsChien-Chieh Lee
3 shared publicationsTomi Li
3 shared publicationsWen-Cheng Ke
3 shared publications
Latest Publications
- Open Access
- 27 January 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (5) , 8636-8645
Quasi-3D Plasmonic Metamaterials with Highly Stretch-Tunable Optical Responses
Three-dimensional (3D) assemblies of metal nanoparticles (NPs) exhibiting strong plasmonic responses have garnered significant interest owing to their potential in optoelectronic and sensing applications. However, the realization of active plasmonic metamaterials based on such architectures remains nontrivial, particularly in achieving uniform and sub-10 nm interparticle spacing within dynamically tunable media. Here, we present mechanically reconfigurable plasmonic nanocomposites composed of 3D stacked liquid gallium nanoparticles (GaNPs) embedded in a polydimethylsiloxane (PDMS) matrix, fabricated through a single-step Ga evaporation process. The resulting GaNPs/PDMS nanocomposites exhibit multilayered NP architectures with narrow interparticle spacing that can act as quasi-3D plasmonic metamaterials, where collective plasmon resonances hybridize with cavity modes to generate plasmon-polariton states. Under applied biaxial strain, the multilayered architecture enables simultaneous modulation of both intralayer and interlayer plasmonic coupling, giving rise to a reversible strain-induced spectral shift exceeding 300 nm. Finite-difference time-domain (FDTD) simulations confirm that the observed resonance shifts primarily originate from variations in both intra- and interlayer interparticle spacing. Based on structural characterization, furthermore, we propose a refined mechanism for the growth and embedment of nanoparticles within the polymer matrix. These findings could advance the understanding of nanoparticle-polymer interactions and benefit the development of mechanically tunable plasmonic metamaterials.
- 27 January 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (5) , 8636-8645
Open AccessQuasi-3D Plasmonic Metamaterials with Highly Stretch-Tunable Optical Responses
Three-dimensional (3D) assemblies of metal nanoparticles (NPs) exhibiting strong plasmonic responses have garnered significant interest owing to their potential in optoelectronic and sensing applications. However, the realization of active plasmonic metamaterials based on such architectures remains nontrivial, particularly in achieving uniform and sub-10 nm interparticle spacing within dynamically tunable media. Here, we present mechanically reconfigurable plasmonic nanocomposites composed of 3D stacked liquid gallium nanoparticles (GaNPs) embedded in a polydimethylsiloxane (PDMS) matrix, fabricated through a single-step Ga evaporation process. The resulting GaNPs/PDMS nanocomposites exhibit multilayered NP architectures with narrow interparticle spacing that can act as quasi-3D plasmonic metamaterials, where collective plasmon resonances hybridize with cavity modes to generate plasmon-polariton states. Under applied biaxial strain, the multilayered architecture enables simultaneous modulation of both intralayer and interlayer plasmonic coupling, giving rise to a reversible strain-induced spectral shift exceeding 300 nm. Finite-difference time-domain (FDTD) simulations confirm that the observed resonance shifts primarily originate from variations in both intra- and interlayer interparticle spacing. Based on structural characterization, furthermore, we propose a refined mechanism for the growth and embedment of nanoparticles within the polymer matrix. These findings could advance the understanding of nanoparticle-polymer interactions and benefit the development of mechanically tunable plasmonic metamaterials.
- Open Access
Plasmon Tuning of Liquid Gallium Nanoparticles through Surface Anodization
In this work, tunable plasmonic liquid gallium nanoparticles (Ga NPs) were prepared through surface anodizing of the particles. Shape deformation of the Ga NPs accompanied with dimpled surface topographies could be induced during electrochemical anodization, and the formation of the anodic oxide shell helps maintain the resulting change in the particle shape. The nanoscale dimple-like textures led to changes in the localized surface plasmon resonance (LSPR) wavelength. A maximal LSPR red-shift of ~77 nm was preliminarily achieved using an anodization voltage of 0.7 V. The experimental results showed that an increase in the oxide shell thickness yielded a negligible difference in the observed LSPR, and finite-difference time-domain (FDTD) simulations also suggested that the LSPR tunability was primarily determined by the shape of the deformed particles. The extent of particle deformation could be adjusted in a very short period of anodization time (~7 s), which offers an efficient way to tune the LSPR response of Ga NPs.
Open AccessPlasmon Tuning of Liquid Gallium Nanoparticles through Surface Anodization
In this work, tunable plasmonic liquid gallium nanoparticles (Ga NPs) were prepared through surface anodizing of the particles. Shape deformation of the Ga NPs accompanied with dimpled surface topographies could be induced during electrochemical anodization, and the formation of the anodic oxide shell helps maintain the resulting change in the particle shape. The nanoscale dimple-like textures led to changes in the localized surface plasmon resonance (LSPR) wavelength. A maximal LSPR red-shift of ~77 nm was preliminarily achieved using an anodization voltage of 0.7 V. The experimental results showed that an increase in the oxide shell thickness yielded a negligible difference in the observed LSPR, and finite-difference time-domain (FDTD) simulations also suggested that the LSPR tunability was primarily determined by the shape of the deformed particles. The extent of particle deformation could be adjusted in a very short period of anodization time (~7 s), which offers an efficient way to tune the LSPR response of Ga NPs.
- Open Access
- 4 February 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (10) , 5579-5584
Fabrication of local micro-contacts to silicon solar cells by dewetting of ultrathin polymer films
A local contact patterning process based on dewetting of 50 nm-thick polystyrene (PS) films has been developed for fabrication of silicon PERC (Passivated Emitter and Rear Cell) solar cells. Holey PS films with a random pattern of holes were prepared on dielectric passivated silicon wafers through the dewetting process, and then served as etch masks for selective plasma etching of dielectric passivation layers, in doing so metal contact patterns could be generated. The impact of local back contact formation on cell performance was studied as a function of the metallization fraction. This chemical-based patterning process, which broadens the applications of dewetting of polymer films, offers an interesting alternative to laser-based approaches as it may avoid silicon surface damage and lower the manufacturing costs. The application of this patterning technique to PERC fabrication could result in a preliminary efficiency of 13.5% with a Voc = 655 mV and a Jsc = 38.4 mA cm−2. An apparent gain in conversion efficiency of 0.6% could be achieved compared to the full-area aluminum back surface field reference cell.
- 4 February 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (10) , 5579-5584
Open AccessFabrication of local micro-contacts to silicon solar cells by dewetting of ultrathin polymer films
A local contact patterning process based on dewetting of 50 nm-thick polystyrene (PS) films has been developed for fabrication of silicon PERC (Passivated Emitter and Rear Cell) solar cells. Holey PS films with a random pattern of holes were prepared on dielectric passivated silicon wafers through the dewetting process, and then served as etch masks for selective plasma etching of dielectric passivation layers, in doing so metal contact patterns could be generated. The impact of local back contact formation on cell performance was studied as a function of the metallization fraction. This chemical-based patterning process, which broadens the applications of dewetting of polymer films, offers an interesting alternative to laser-based approaches as it may avoid silicon surface damage and lower the manufacturing costs. The application of this patterning technique to PERC fabrication could result in a preliminary efficiency of 13.5% with a Voc = 655 mV and a Jsc = 38.4 mA cm−2. An apparent gain in conversion efficiency of 0.6% could be achieved compared to the full-area aluminum back surface field reference cell.
- 21 March 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (8) , 2259-2263
Low‐temperature grown indium oxide nanowire‐based antireflection coatings for multi‐crystalline silicon solar cells
Light harvesting by indium oxide nanowires (InO NWs) as an antireflection layer on multi‐crystalline silicon (mc‐Si) solar cells has been investigated. The low‐temperature growth of InO NWs was performed in electron cyclotron resonance (ECR) plasma with an O2–Ar system using indium nanocrystals as seed particles via the self‐catalyzed growth mechanism. The size‐dependence of antireflection properties of InO NWs was studied. A considerable enhancement in short‐circuit current (from 35.39 to 38.33 mA cm−2) without deterioration of other performance parameters is observed for mc‐Si solar cells coated with InO NWs.
- 21 March 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (8) , 2259-2263
Low‐temperature grown indium oxide nanowire‐based antireflection coatings for multi‐crystalline silicon solar cells
Light harvesting by indium oxide nanowires (InO NWs) as an antireflection layer on multi‐crystalline silicon (mc‐Si) solar cells has been investigated. The low‐temperature growth of InO NWs was performed in electron cyclotron resonance (ECR) plasma with an O2–Ar system using indium nanocrystals as seed particles via the self‐catalyzed growth mechanism. The size‐dependence of antireflection properties of InO NWs was studied. A considerable enhancement in short‐circuit current (from 35.39 to 38.33 mA cm−2) without deterioration of other performance parameters is observed for mc‐Si solar cells coated with InO NWs.
- Open Access
- 17 April 2015
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 4 (7) , P213-P219
Investigation of Electron Cyclotron Resonance Chemical Vapor Deposition Process for a-Si:H Deposition, Film Characterization and In Situ Plasma Diagnostics
We present the application of quadrupole mass spectrometry (QMS) with threshold ionization mass spectrometry (TIMS), optical emission spectroscopy (OES) with an actinometry method, and Langmuir probe (LP) as an integrated technique for in situ plasma characterization of the electron cyclotron resonance chemical vapor deposition (ECR-CVD) of hydrogenated amorphous silicon (a-Si:H). The main aim of this study was to determine the relationship among the process parameters, plasma characteristics, and thin film properties, including the microstructure parameter (R*), hydrogen content (CH), and a-Si:H film growth rate. The physical properties of plasma, such as the electron density (Ne), electron energy (Te), and sheath potential (Vs), were studied using an LP and OES. In addition to the general plasma properties, the ion density (Ni) and plasma electronegativity were examined. The results indicate the ECR plasma source has high potential for producing a high-quality a-Si:H film because of the availability of few high silanes (SinH2n+2, n > 2); furthermore, the results indicate an obvious difference in the QMS analysis results between plasma and gas. Therefore, the consumption of parent molecules must be considered. The TIMS method was applied to estimate the relative concentration of ground-state silane radicals (SiHx, x < 4) and consumption of SiH4. The results indicate that, in addition to the degree of ionization, the consumption of SiH4 and Vs are key factors affecting the thin film growth rate. When microwave power density increases, the values of Ni, Ne, and Vs increase considerably, but the plasma electronegativity remains unchanged. Furthermore, we compared our results with the TIMS analysis reported by other authors and found that the ratio of SiH2 to SiH3 obtained using QMS and TIMS can be considered an indicator of film quality for R* in the ECR-CVD process.
- 17 April 2015
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 4 (7) , P213-P219
Open AccessInvestigation of Electron Cyclotron Resonance Chemical Vapor Deposition Process for a-Si:H Deposition, Film Characterization and In Situ Plasma Diagnostics
We present the application of quadrupole mass spectrometry (QMS) with threshold ionization mass spectrometry (TIMS), optical emission spectroscopy (OES) with an actinometry method, and Langmuir probe (LP) as an integrated technique for in situ plasma characterization of the electron cyclotron resonance chemical vapor deposition (ECR-CVD) of hydrogenated amorphous silicon (a-Si:H). The main aim of this study was to determine the relationship among the process parameters, plasma characteristics, and thin film properties, including the microstructure parameter (R*), hydrogen content (CH), and a-Si:H film growth rate. The physical properties of plasma, such as the electron density (Ne), electron energy (Te), and sheath potential (Vs), were studied using an LP and OES. In addition to the general plasma properties, the ion density (Ni) and plasma electronegativity were examined. The results indicate the ECR plasma source has high potential for producing a high-quality a-Si:H film because of the availability of few high silanes (SinH2n+2, n > 2); furthermore, the results indicate an obvious difference in the QMS analysis results between plasma and gas. Therefore, the consumption of parent molecules must be considered. The TIMS method was applied to estimate the relative concentration of ground-state silane radicals (SiHx, x < 4) and consumption of SiH4. The results indicate that, in addition to the degree of ionization, the consumption of SiH4 and Vs are key factors affecting the thin film growth rate. When microwave power density increases, the values of Ni, Ne, and Vs increase considerably, but the plasma electronegativity remains unchanged. Furthermore, we compared our results with the TIMS analysis reported by other authors and found that the ratio of SiH2 to SiH3 obtained using QMS and TIMS can be considered an indicator of film quality for R* in the ECR-CVD process.
- 1 March 2015
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 412, 5-10
Investigation of interface quality and passivation improvement with a-SiO:H deposited by ECRCVD at low temperature
- 1 March 2015
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 412, 5-10
Investigation of interface quality and passivation improvement with a-SiO:H deposited by ECRCVD at low temperature
- 1 February 2015
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 622, 669-675
Influence of annealing on microstructural and photoelectrochemical characteristics of CuSCN thin films via electrochemical process
- 1 February 2015
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 622, 669-675
Influence of annealing on microstructural and photoelectrochemical characteristics of CuSCN thin films via electrochemical process
- 1 November 2014
- Published by Elsevier in Thin Solid Films
- Vol. 570, 591-594
Investigation of hydrogenated amorphous silicon as passivation layer by high density plasma
- 1 November 2014
- Published by Elsevier in Thin Solid Films
- Vol. 570, 591-594
Investigation of hydrogenated amorphous silicon as passivation layer by high density plasma
- Open Access
- 10 August 2014
- Published by Wiley in International Journal of Photoenergy
- Vol. 2014, 1-8
Low Temperature (180°C) Growth of Smooth Surface Germanium Epilayers on Silicon Substrates Using Electron Cyclotron Resonance Chemical Vapor Deposition
This paper describes a new method to grow thin germanium (Ge) epilayers (40 nm) on c-Si substrates at a low growth temperature of 180°C using electron cyclotron resonance chemical vapor deposition (ECR-CVD) process. The full width at half maximum (FWHM) of the Ge (004) in X-ray diffraction pattern and the compressive stain in a Ge epilayer of 683 arcsec and 0.12% can be achieved. Moreover, the Ge/Si interface is observed by transmission electron microscopy to demonstrate the epitaxial growth of Ge on Si and the surface roughness is 0.342 nm. The thin-thickness and smooth surface of Ge epilayer grown on Si in this study is suitable to be a virtual substrate for developing the low cost and high efficiency III-V/Si tandem solar cells in our opinion. Furthermore, the low temperature process can not only decrease costs but can also reduce the restriction of high temperature processes on device manufacturing.
- 10 August 2014
- Published by Wiley in International Journal of Photoenergy
- Vol. 2014, 1-8
Open AccessLow Temperature (180°C) Growth of Smooth Surface Germanium Epilayers on Silicon Substrates Using Electron Cyclotron Resonance Chemical Vapor Deposition
This paper describes a new method to grow thin germanium (Ge) epilayers (40 nm) on c-Si substrates at a low growth temperature of 180°C using electron cyclotron resonance chemical vapor deposition (ECR-CVD) process. The full width at half maximum (FWHM) of the Ge (004) in X-ray diffraction pattern and the compressive stain in a Ge epilayer of 683 arcsec and 0.12% can be achieved. Moreover, the Ge/Si interface is observed by transmission electron microscopy to demonstrate the epitaxial growth of Ge on Si and the surface roughness is 0.342 nm. The thin-thickness and smooth surface of Ge epilayer grown on Si in this study is suitable to be a virtual substrate for developing the low cost and high efficiency III-V/Si tandem solar cells in our opinion. Furthermore, the low temperature process can not only decrease costs but can also reduce the restriction of high temperature processes on device manufacturing.
- 7 May 2014
- Published by Taylor & Francis in International Journal of Radiation Biology
- Vol. 90 (10) , 841-852
Radioprotective effects ofAntrodia cinnamomeaare enhanced on immune cells and inhibited on cancer cells
Purpose: The radioprotective effects of Antrodia cinnamomea (AC) were investigated for understanding the potential usefulness of AC as an adjunct treatment for reducing radiation side-effects. Materials and methods: In this study, we determined the ability of AC extracts (AC539) to reduce radiation side-effects by analyzing cellular viability in normal mouse spleen immune cells and human cancer cells with different radiosensitivity. We further detected the effect of AC on radiation-induced changes in cytokine- and inflammatory-related gene expressions. Furthermore, apoptosis assay was performed to determine whether AC could inhibit radiation-induced cytotoxicity. Results: We found that an AC dose of 100–150 μg/ml in a time-dependent manner was the most effective in blocking radiation-induced cytotoxicity, in vitro. Radiation-induced cytotoxicity was inhibited in spleen immune cells by 37–56%; however, pretreatment of human colorectal cancer cell line HT-29 with AC did not have any effect on radiation-induced cytotoxicity, while pretreatment of radiosensitive human breast cancer cell lines BT-474 with AC caused a moderate enhancement of radiation-induced damage. Furthermore, AC pretreatment differentially regulated the mRNA expression of several important immunomodulatory genes in response to irradiation in normal and cancer cells. Conclusions: Our data indicate that AC may inhibit important immunoregulatory signaling which could be vital in the avoidance of an over-activated cytotoxic and inflammatory response of the immune system caused by radiation-induced tissue damage. Additionally, AC does not provide a radioprotective effect to tumor cells but instead enhances radiation-induced inflammation and cytotoxicity in cancer.
- 7 May 2014
- Published by Taylor & Francis in International Journal of Radiation Biology
- Vol. 90 (10) , 841-852
Radioprotective effects ofAntrodia cinnamomeaare enhanced on immune cells and inhibited on cancer cells
Purpose: The radioprotective effects of Antrodia cinnamomea (AC) were investigated for understanding the potential usefulness of AC as an adjunct treatment for reducing radiation side-effects. Materials and methods: In this study, we determined the ability of AC extracts (AC539) to reduce radiation side-effects by analyzing cellular viability in normal mouse spleen immune cells and human cancer cells with different radiosensitivity. We further detected the effect of AC on radiation-induced changes in cytokine- and inflammatory-related gene expressions. Furthermore, apoptosis assay was performed to determine whether AC could inhibit radiation-induced cytotoxicity. Results: We found that an AC dose of 100–150 μg/ml in a time-dependent manner was the most effective in blocking radiation-induced cytotoxicity, in vitro. Radiation-induced cytotoxicity was inhibited in spleen immune cells by 37–56%; however, pretreatment of human colorectal cancer cell line HT-29 with AC did not have any effect on radiation-induced cytotoxicity, while pretreatment of radiosensitive human breast cancer cell lines BT-474 with AC caused a moderate enhancement of radiation-induced damage. Furthermore, AC pretreatment differentially regulated the mRNA expression of several important immunomodulatory genes in response to irradiation in normal and cancer cells. Conclusions: Our data indicate that AC may inhibit important immunoregulatory signaling which could be vital in the avoidance of an over-activated cytotoxic and inflammatory response of the immune system caused by radiation-induced tissue damage. Additionally, AC does not provide a radioprotective effect to tumor cells but instead enhances radiation-induced inflammation and cytotoxicity in cancer.