Wei Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Wei Li has a total of 95 co-authors. Here are the top co-authors by number of shared publications:
Jian Chen
Key Laboratory of Efficient & Clean Energy Utilization School of Energy and Power Engineering, Changsha University of Science & Technology Changsha China
8 shared publications- Cong Li
Institute of Energy and Power Engineering Changsha University of Science and Technology Changsha P. R. China
5 shared publications - Jian Chen
Key Laboratory of Efficient & Clean Energy Utilization, School of Energy and Power Engineering, Changsha University of Science & Technology, Changsha 410114, China
5 shared publications Cong Li
Key Laboratory of Efficient & Clean Energy Utilization School of Energy and Power Engineering, Changsha University of Science & Technology Changsha China
4 shared publications- Jianjun He
School of Energy and Power Engineering, Changsha University of Science and Technology, Changsha, China
4 shared publications Jianjun He
School of Energy and Power Engineering, Changsha University of Science and Technology, Changsha, China
3 shared publications
Latest Publications
Oxygen‐Plasma‐Induced Surface Reconstruction of WSe 2 Enables Nonvolatile Optoelectronic Synapses for in‐Sensor Neuromorphic Vision
Developing neuromorphic visual systems that integrate sensing, memory, and information processing is important for reducing data‐transfer overhead in edge vision. 2D WSe 2 offers strong light‐matter interaction, but its intrinsically rapid carrier relaxation generally leads to volatile photoresponses that are unfavorable for nonvolatile synaptic weight storage. Here, we develop a two‐terminal WSe 2 optoelectronic synapse through carefully controlled oxygen‐plasma‐induced surface reconstruction. The contact‐first, plasma‐reconstruction‐second strategy employs preformed metal electrodes to physically shield the underlying contact regions while allowing the exposed WSe 2 surface to undergo reconstruction. The resulting device exhibits persistent photogating, wavelength‐dependent optical potentiation, reversible electrical depression, and a large long‐term potentiation/depression (LTP/LTD) conductance dynamic range of 426. A high/low resistance state (HRS/LRS) resistance ratio on the order of 10 5 is maintained together with stable operation over more than 4000 cycles. An experimentally calibrated hardware‐software co‐simulation further demonstrates the potential of the measured optoelectronic response for front‐end noise suppression, highlighting a simple surface‐engineering route toward integrated sensing, nonvolatile weight storage, and neuromorphic preprocessing.
Oxygen‐Plasma‐Induced Surface Reconstruction of WSe 2 Enables Nonvolatile Optoelectronic Synapses for in‐Sensor Neuromorphic Vision
Developing neuromorphic visual systems that integrate sensing, memory, and information processing is important for reducing data‐transfer overhead in edge vision. 2D WSe 2 offers strong light‐matter interaction, but its intrinsically rapid carrier relaxation generally leads to volatile photoresponses that are unfavorable for nonvolatile synaptic weight storage. Here, we develop a two‐terminal WSe 2 optoelectronic synapse through carefully controlled oxygen‐plasma‐induced surface reconstruction. The contact‐first, plasma‐reconstruction‐second strategy employs preformed metal electrodes to physically shield the underlying contact regions while allowing the exposed WSe 2 surface to undergo reconstruction. The resulting device exhibits persistent photogating, wavelength‐dependent optical potentiation, reversible electrical depression, and a large long‐term potentiation/depression (LTP/LTD) conductance dynamic range of 426. A high/low resistance state (HRS/LRS) resistance ratio on the order of 10 5 is maintained together with stable operation over more than 4000 cycles. An experimentally calibrated hardware‐software co‐simulation further demonstrates the potential of the measured optoelectronic response for front‐end noise suppression, highlighting a simple surface‐engineering route toward integrated sensing, nonvolatile weight storage, and neuromorphic preprocessing.
- 30 June 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
Influence of NiCrAlY Content in TiC‐Based Self‐Healing Coating and Laser Remelting on Creep–Fatigue and Remnant Properties of 321 Stainless Steel
The remnant creep and tensile properties of AISI 321 steels after creep–fatigue exposure are crucial to their remnant service life. Therefore, based on our recently reported plasma‐sprayed TiC‐based self‐healing coating, an improved self‐healing coating consisting of a NiCrAlY layer, a TiC–50‐wt.% NiCrAlY layer, and an Al₂O₃–13% TiO₂ (AT13)–25‐wt.% NiCrAlY layer was designed and prepared for AISI 321 steel by plasma spraying and further laser remelting treatment. The results indicated that such laser remelting self‐healing coatings could further simultaneously improve the creep–fatigue resistance and remnant creep/tensile properties compared with the counterpart plasma‐sprayed self‐healing coating. This improvement is attributed to enhanced interlayer bonding, reduced porosity, and the introduction of dislocations due to thermal stresses during laser remelting treatment. Furthermore, the initial hardening observed during creep–fatigue exposure is due to dislocation strengthening, twin strengthening, and carbide strengthening, while the subsequent softening occurred due to dynamic recovery and coarsening of carbides as well as twin degradation.
- 30 June 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
Influence of NiCrAlY Content in TiC‐Based Self‐Healing Coating and Laser Remelting on Creep–Fatigue and Remnant Properties of 321 Stainless Steel
The remnant creep and tensile properties of AISI 321 steels after creep–fatigue exposure are crucial to their remnant service life. Therefore, based on our recently reported plasma‐sprayed TiC‐based self‐healing coating, an improved self‐healing coating consisting of a NiCrAlY layer, a TiC–50‐wt.% NiCrAlY layer, and an Al₂O₃–13% TiO₂ (AT13)–25‐wt.% NiCrAlY layer was designed and prepared for AISI 321 steel by plasma spraying and further laser remelting treatment. The results indicated that such laser remelting self‐healing coatings could further simultaneously improve the creep–fatigue resistance and remnant creep/tensile properties compared with the counterpart plasma‐sprayed self‐healing coating. This improvement is attributed to enhanced interlayer bonding, reduced porosity, and the introduction of dislocations due to thermal stresses during laser remelting treatment. Furthermore, the initial hardening observed during creep–fatigue exposure is due to dislocation strengthening, twin strengthening, and carbide strengthening, while the subsequent softening occurred due to dynamic recovery and coarsening of carbides as well as twin degradation.
- Open Access
- 15 April 2025
- Published by Elsevier in Chinese Journal of Mechanical Engineering
- Vol. 38 (1) , 1-22
Effect of Aluminizing and Laser Shock Peening Treatments on the High-Temperature Oxidation Resistance of AISI 321 Stainless Steel for Solar Thermal Power Heat Exchanger
- 15 April 2025
- Published by Elsevier in Chinese Journal of Mechanical Engineering
- Vol. 38 (1) , 1-22
Open AccessEffect of Aluminizing and Laser Shock Peening Treatments on the High-Temperature Oxidation Resistance of AISI 321 Stainless Steel for Solar Thermal Power Heat Exchanger
- 10 March 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (15) , 10934-10944
Se-vacancy induced structural reconstruction of iron nickel selenium nanosheets for efficient and durable electrocatalytic alkaline water and seawater oxidation
Se-vacancy-rich Fe-doped NiSe nanosheets were synthesized for the oxygen evolution reaction in both alkaline water and seawater. In situ Raman revealed Se vacancies promotie NiFeOOH and SeO42− formation enhancing catalytic performance.
- 10 March 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (15) , 10934-10944
Se-vacancy induced structural reconstruction of iron nickel selenium nanosheets for efficient and durable electrocatalytic alkaline water and seawater oxidation
Se-vacancy-rich Fe-doped NiSe nanosheets were synthesized for the oxygen evolution reaction in both alkaline water and seawater. In situ Raman revealed Se vacancies promotie NiFeOOH and SeO42− formation enhancing catalytic performance.
- Open Access
- 1 January 2025
- Published by Wiley in Structural Control and Health Monitoring
- Vol. 2025 (1)
Fatigue Monitoring of 321 Steel Coated by Laser Additively Manufactured CoCrFeMnNi High‐Entropy Alloy Using Acoustic Emission Technique
Fatigue failure is a common mode of deterioration for steel cables (e.g., 321 stainless steel) in cable‐stayed bridges. In this case, given that the FeCoNiCrMn high‐entropy alloy (HEA) coatings have been found to simultaneously improve the fatigue and corrosion resistance of 321 steel, the fatigue crack growth behavior of 321 steel coated with selective laser melting CoCrFeMnNi HEA was further studied in this work. The results indicate that the CoCrFeMnNi alloy coating is able to increase the fatigue crack growth resistance of 321 steel by 21.43% compared to the uncoated 321 steel, and this is because the initiation of crack is mitigated by the angular disparities between adjacent grains and an increased dislocation density in the coating. Furthermore, the acoustic emission (AE) technique was used to track fatigue damage and predict fatigue crack growth life. It was found that crack length could be effectively monitored and predicted using the count and energy parameter, suggesting material and stress ratio independence in the AE technique.
- 1 January 2025
- Published by Wiley in Structural Control and Health Monitoring
- Vol. 2025 (1)
Open AccessFatigue Monitoring of 321 Steel Coated by Laser Additively Manufactured CoCrFeMnNi High‐Entropy Alloy Using Acoustic Emission Technique
Fatigue failure is a common mode of deterioration for steel cables (e.g., 321 stainless steel) in cable‐stayed bridges. In this case, given that the FeCoNiCrMn high‐entropy alloy (HEA) coatings have been found to simultaneously improve the fatigue and corrosion resistance of 321 steel, the fatigue crack growth behavior of 321 steel coated with selective laser melting CoCrFeMnNi HEA was further studied in this work. The results indicate that the CoCrFeMnNi alloy coating is able to increase the fatigue crack growth resistance of 321 steel by 21.43% compared to the uncoated 321 steel, and this is because the initiation of crack is mitigated by the angular disparities between adjacent grains and an increased dislocation density in the coating. Furthermore, the acoustic emission (AE) technique was used to track fatigue damage and predict fatigue crack growth life. It was found that crack length could be effectively monitored and predicted using the count and energy parameter, suggesting material and stress ratio independence in the AE technique.
- 1 May 2024
- Published by Elsevier in Materials Letters
- Vol. 367
Photodetector based on 2H-WSe2 grown by physical vapor deposition method
- 1 May 2024
- Published by Elsevier in Materials Letters
- Vol. 367
Photodetector based on 2H-WSe2 grown by physical vapor deposition method
- 2 September 2022
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 45 (12) , 3746-3763
Remnant tensile and creep properties of aluminized AISI 321 austenite stainless steel under prior creep–fatigue interaction
Aluminized AISI 321 steels applied as heat exchange tube are generally subjected to creep–fatigue (C‐F) exposure during service. Remaining tensile and creep performance of this steel at 620°C were therefore studied under prior C‐F deformation. Results revealed that residual properties exhibit an initial increase and followed degradation with rising lifetime fraction of prior C‐F. The tensile strength and creep lifespan reach highest at 30% lifetime fraction, since dislocation cell networks are well developed and secondary nanotwins are activated at substrate. Additionally, dynamic recovery and wavy slips occurred in coatings partially accommodate local plastic deformations and inhibit defect initiations, avoiding premature material fracture. On the other hand, these networks could restrain the increase in coating thicknesses. When the lifetime fraction of prior C‐F increases to 80%, declined remnant properties are observed, which is attributed to the recovery of dislocation cells and carbide coarsening. Meanwhile, coating microcracks also accelerate steel failure.
- 2 September 2022
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 45 (12) , 3746-3763
Remnant tensile and creep properties of aluminized AISI 321 austenite stainless steel under prior creep–fatigue interaction
Aluminized AISI 321 steels applied as heat exchange tube are generally subjected to creep–fatigue (C‐F) exposure during service. Remaining tensile and creep performance of this steel at 620°C were therefore studied under prior C‐F deformation. Results revealed that residual properties exhibit an initial increase and followed degradation with rising lifetime fraction of prior C‐F. The tensile strength and creep lifespan reach highest at 30% lifetime fraction, since dislocation cell networks are well developed and secondary nanotwins are activated at substrate. Additionally, dynamic recovery and wavy slips occurred in coatings partially accommodate local plastic deformations and inhibit defect initiations, avoiding premature material fracture. On the other hand, these networks could restrain the increase in coating thicknesses. When the lifetime fraction of prior C‐F increases to 80%, declined remnant properties are observed, which is attributed to the recovery of dislocation cells and carbide coarsening. Meanwhile, coating microcracks also accelerate steel failure.
- Open Access
Low-Cycle Fatigue and Fracture Behavior of Aluminized Stainless Steel AISI 321 for Solar Thermal Power Generation Systems
The microstructure, low-cycle fatigue property, and fracture behavior of as-received and aluminized steel were investigated at room temperature, respectively. The results reveal that the aluminized layer is mainly composed of three layers: (I) the external Al2O3 layer, (II) the transition Fe-Al mesophase layer, and (III) the diffusion layer with AlFe and AlCrFe phase. The microhardness of as-received steel lower than that of aluminized steel until the distance from aluminized layer is greater than 150 μm. Compared to the original steel, the aluminized steel exhibits lower stress amplitude and fatigue life, which is correlated to the surface integrity. According to the Coffin-Manson relationship, the fatigue-ductility coefficients for as-received and aluminized steel is 4.347 and 3.528, respectively. Fractographic analysis reveals that the fatigue cracks tend to nucleate at the coating and propagate through the grain boundaries apace.
Open AccessLow-Cycle Fatigue and Fracture Behavior of Aluminized Stainless Steel AISI 321 for Solar Thermal Power Generation Systems
The microstructure, low-cycle fatigue property, and fracture behavior of as-received and aluminized steel were investigated at room temperature, respectively. The results reveal that the aluminized layer is mainly composed of three layers: (I) the external Al2O3 layer, (II) the transition Fe-Al mesophase layer, and (III) the diffusion layer with AlFe and AlCrFe phase. The microhardness of as-received steel lower than that of aluminized steel until the distance from aluminized layer is greater than 150 μm. Compared to the original steel, the aluminized steel exhibits lower stress amplitude and fatigue life, which is correlated to the surface integrity. According to the Coffin-Manson relationship, the fatigue-ductility coefficients for as-received and aluminized steel is 4.347 and 3.528, respectively. Fractographic analysis reveals that the fatigue cracks tend to nucleate at the coating and propagate through the grain boundaries apace.
- Open Access
- 13 March 2020
- Published by Wiley in International Journal of Photoenergy
- Vol. 2020, 1-9
Study on Tensile Creep Behavior of 12Cr1MoV Alloy Steel under High-Temperature Alkali Metal Salt Environment for Solar Thermal Power Generation
The heat exchange tubes of solar thermal power generation work in molten salt environment with periodic temperature change. In order to reveal the tensile creep behavior of 12Cr1MoV pipeline steel under high-temperature alkali metal salt environment, the tensile creep behavior of 12Cr1MoV alloy under different applied load and reaction temperature in high-temperature alkali metal chloride salt environment was studied. The results show that the deformation of 12Cr1MoV alloy in 600°C, NaCl-35%KCl mixed salt environment is mainly controlled by diffusion creep; with the increase of stress, the creep life of 12Cr1MoV alloy decreases. The creep fracture mechanism of 12Cr1MoV alloy in 600°C, NaCl-35%KCl mixed salt environment is intergranular ductile fracture; the increase of temperature will enhance the activation and oxidation of the chlorine atoms, thereby accelerating the corrosion of the base metal and increasing the spheroidization speed of the pearlite matrix, and the creep deformation rate of the alloy increases with increasing temperature.
- 13 March 2020
- Published by Wiley in International Journal of Photoenergy
- Vol. 2020, 1-9
Open AccessStudy on Tensile Creep Behavior of 12Cr1MoV Alloy Steel under High-Temperature Alkali Metal Salt Environment for Solar Thermal Power Generation
The heat exchange tubes of solar thermal power generation work in molten salt environment with periodic temperature change. In order to reveal the tensile creep behavior of 12Cr1MoV pipeline steel under high-temperature alkali metal salt environment, the tensile creep behavior of 12Cr1MoV alloy under different applied load and reaction temperature in high-temperature alkali metal chloride salt environment was studied. The results show that the deformation of 12Cr1MoV alloy in 600°C, NaCl-35%KCl mixed salt environment is mainly controlled by diffusion creep; with the increase of stress, the creep life of 12Cr1MoV alloy decreases. The creep fracture mechanism of 12Cr1MoV alloy in 600°C, NaCl-35%KCl mixed salt environment is intergranular ductile fracture; the increase of temperature will enhance the activation and oxidation of the chlorine atoms, thereby accelerating the corrosion of the base metal and increasing the spheroidization speed of the pearlite matrix, and the creep deformation rate of the alloy increases with increasing temperature.
- Open Access
- 26 February 2020
- Published by Wiley in International Journal of Photoenergy
- Vol. 2020, 1-13
Effect of Laser Shock Processing and Aluminizing on Microstructure and High-Temperature Creep Properties of 321 Stainless Steel for Solar Thermal Power Generation
The aluminized layer of 321 stainless steel was treated by laser shock processing (LSP). The effects of constituent distribution and microstructure change of the aluminized layer in 321 stainless steel on creep performance at high temperature were investigated. SEM and EDS results reveal that aluminized coating is mainly composed of an Al2O3 outer layer, the transition layer of the Fe-Al phase, and the diffusion layer. Additionally, LSP conducted on coating surface not only improves the density of the layer structure, resulting in an increment on the bonding strength of both infiltration layer and substrate, but also leaves higher residual compressive stress in the aluminized layer which improves its creep life effectively. Experimental results indicate that the microhardness of the laser-shocked region is improved strongly by the refined grains and the reconstruction of microstructures. Meanwhile, the roughness and microhardness of aluminized steel are found to increase with the laser impact times. On the other hand, the intermetallic layers, whose microstructure is stable enough to inhibit crack initiation, reinforce strength greatly. The anticreep life of aluminized sample with three times LSP was increased by 232.1% as compared to aluminized steel, which could attribute to the increased dislocation density in the peened sample as well as the decrease of creep voids in size and density.
- 26 February 2020
- Published by Wiley in International Journal of Photoenergy
- Vol. 2020, 1-13
Open AccessEffect of Laser Shock Processing and Aluminizing on Microstructure and High-Temperature Creep Properties of 321 Stainless Steel for Solar Thermal Power Generation
The aluminized layer of 321 stainless steel was treated by laser shock processing (LSP). The effects of constituent distribution and microstructure change of the aluminized layer in 321 stainless steel on creep performance at high temperature were investigated. SEM and EDS results reveal that aluminized coating is mainly composed of an Al2O3 outer layer, the transition layer of the Fe-Al phase, and the diffusion layer. Additionally, LSP conducted on coating surface not only improves the density of the layer structure, resulting in an increment on the bonding strength of both infiltration layer and substrate, but also leaves higher residual compressive stress in the aluminized layer which improves its creep life effectively. Experimental results indicate that the microhardness of the laser-shocked region is improved strongly by the refined grains and the reconstruction of microstructures. Meanwhile, the roughness and microhardness of aluminized steel are found to increase with the laser impact times. On the other hand, the intermetallic layers, whose microstructure is stable enough to inhibit crack initiation, reinforce strength greatly. The anticreep life of aluminized sample with three times LSP was increased by 232.1% as compared to aluminized steel, which could attribute to the increased dislocation density in the peened sample as well as the decrease of creep voids in size and density.