S. Sakthivelu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
S. Sakthivelu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
M. Meignanamoorthy
3 shared publications- Chanakyan Chandrasekaran
Global Academy of Technology
2 shared publications - Manickam Ravichandran
Department of Mechanical Engineering, K.Ramakrishnan College of Engineering, Samayapuram, Trichy, India
2 shared publications P. P. Sethusundaram
Department of Mechanical Engineering, M.Kumarasamy College of Engineering, Karur, India
2 shared publications- Alagarsamy Sivasamy
Department of Mechanical Engineering, Shanmuganathan Engineering College, Pudukkottai, India
1 shared publication M. Ravichandran
Department of Mechanical Engineering , Chendhuran College of Engineering and Technology , Pudukkottai , India
1 shared publication
Latest Publications
- 1 September 2021
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 9 (3) , 035046
A hybrid approach for prediction of machining performances of glass fiber reinforced plastic (Epoxy) composites
In recent years, Glass Fiber Reinforced Plastic (GFRP) composites are more potential materials for usage in various structural applications in aerospace and automobile industries, owing to its favorable properties, such as light weight, specific strength, high elastic modulus and excellent corrosion resistance. This paper presents a new hybrid approach for multi-objective optimization of machining parameters on GFRP composite using Taguchi coupled grey relational (GR) and desirability function (DF) approach. The end milling of GFRP composite was performed as per Taguchi’s L16 orthogonal array by considering three input parameters: viz cutting speed (V), feed rate (F) and depth of cut (D), each at four levels. The material removal rate (MRR), surface roughness (SR) and tool wear (TW) were chosen as output responses. The main effect plot was used to determine the optimum level of machining parameters on the multiple responses. An experimental result revealed that, the optimum level of parameters obtained by GR analysis is V 2 F 3 D 4 . Similarly, the optimum level of parameters obtained by DF approach is V 2 F 4 D 4. Moreover, analysis of variance (ANOVA) was applied to examine the significance of the parameters. Based on the ANOVA results, it has been proved that the depth of cut was the most significant parameter, trailed by feed rate and cutting speed, respectively. It was also confirmed that the P-values of depth of cut for both analyses are 0.017 and 0.039, which is less than 0.05. Finally, the confirmation tests exhibited that the DA approach was employed better in terms of determining the optimum level of machining parameters as compared to GR analysis.
- 1 September 2021
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 9 (3) , 035046
A hybrid approach for prediction of machining performances of glass fiber reinforced plastic (Epoxy) composites
In recent years, Glass Fiber Reinforced Plastic (GFRP) composites are more potential materials for usage in various structural applications in aerospace and automobile industries, owing to its favorable properties, such as light weight, specific strength, high elastic modulus and excellent corrosion resistance. This paper presents a new hybrid approach for multi-objective optimization of machining parameters on GFRP composite using Taguchi coupled grey relational (GR) and desirability function (DF) approach. The end milling of GFRP composite was performed as per Taguchi’s L16 orthogonal array by considering three input parameters: viz cutting speed (V), feed rate (F) and depth of cut (D), each at four levels. The material removal rate (MRR), surface roughness (SR) and tool wear (TW) were chosen as output responses. The main effect plot was used to determine the optimum level of machining parameters on the multiple responses. An experimental result revealed that, the optimum level of parameters obtained by GR analysis is V 2 F 3 D 4 . Similarly, the optimum level of parameters obtained by DF approach is V 2 F 4 D 4. Moreover, analysis of variance (ANOVA) was applied to examine the significance of the parameters. Based on the ANOVA results, it has been proved that the depth of cut was the most significant parameter, trailed by feed rate and cutting speed, respectively. It was also confirmed that the P-values of depth of cut for both analyses are 0.017 and 0.039, which is less than 0.05. Finally, the confirmation tests exhibited that the DA approach was employed better in terms of determining the optimum level of machining parameters as compared to GR analysis.
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 37, 3480-3484
Influence of different reinforcements on properties of metal matrix composites: A review
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 37, 3480-3484
Influence of different reinforcements on properties of metal matrix composites: A review
- 23 August 2020
- Published by Springer Nature in Silicon
- Vol. 13 (4) , 1285-1294
Experimental Investigation and Analysis of Properties and Dry Sliding Wear Behavior of Al -Fe-Si Alloy Matrix Composites
- 23 August 2020
- Published by Springer Nature in Silicon
- Vol. 13 (4) , 1285-1294
Experimental Investigation and Analysis of Properties and Dry Sliding Wear Behavior of Al -Fe-Si Alloy Matrix Composites
- Open Access
- 1 January 2018
- Published by Walter de Gruyter GmbH in Mechanics and Mechanical Engineering
- Vol. 22 (1) , 357-370
Synthesis of Metal Matrix Composites through Stir Casting Process – a Review
Metal is the one of the important material in engineering materials because of their high strength to weight ratio. However the pure metals cannot be used as engineering materials due to their ductile property. So, to improve their mechanical properties, some of the high strength materials (not metals) were added as reinforcement to improve the mechanical properties of pure metals and the newly developed material is called as metal matrix composites. At present, Aluminium, Copper, Magnesium, Titanium and Iron have been used as matrix materials and materials like TiC, SiC, B4C, WC, Cr3C, TiO2, ZrO2, Gr, MoS2and Si3N4have been used as reinforcements. There are many processing techniques to fabricate metal matrix composites namely stir casting, ultra-sonic assisted casting, compo-casting, rheo casting, powder metallurgy technique, etc,. Among these, stir casting process is the most suitable and economical method to fabricate the metal matrix composites. In this article, an effort has been made to review the work of various researchers to fabricate metal matrix composites through stir casting process.
- 1 January 2018
- Published by Walter de Gruyter GmbH in Mechanics and Mechanical Engineering
- Vol. 22 (1) , 357-370
Open AccessSynthesis of Metal Matrix Composites through Stir Casting Process – a Review
Metal is the one of the important material in engineering materials because of their high strength to weight ratio. However the pure metals cannot be used as engineering materials due to their ductile property. So, to improve their mechanical properties, some of the high strength materials (not metals) were added as reinforcement to improve the mechanical properties of pure metals and the newly developed material is called as metal matrix composites. At present, Aluminium, Copper, Magnesium, Titanium and Iron have been used as matrix materials and materials like TiC, SiC, B4C, WC, Cr3C, TiO2, ZrO2, Gr, MoS2and Si3N4have been used as reinforcements. There are many processing techniques to fabricate metal matrix composites namely stir casting, ultra-sonic assisted casting, compo-casting, rheo casting, powder metallurgy technique, etc,. Among these, stir casting process is the most suitable and economical method to fabricate the metal matrix composites. In this article, an effort has been made to review the work of various researchers to fabricate metal matrix composites through stir casting process.