Christer Sandberg
Research Subjects
Christer Sandberg has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Fritjof Nilsson
School of Engineering Sciences in Chemistry, Biotechnology and Health, Fibre and Polymer Technology, KTH Royal Institute of Technology, Stockholm, Sweden
2 shared publications Rita Ferritsius
6311 Mid Sweden University , SE-851 70 Sundsvall , Sweden
2 shared publications- Birgitta A. Engberg
FSCN Research Centre, Department of Engineering, Mathematics and Science Education, Mid Sweden University, SE-85170 Sundsvall, Sweden
1 shared publication - Geoffrey Daniel
Department of Forest Products/Wood Science Swedish University of Agricultural Sciences Uppsala Sweden
1 shared publication - Jan Hill
QualTech , Tyringe , Sweden
1 shared publication Jan-Erik Berg
Mid Sweden University
1 shared publication
Latest Publications
- Open Access
- 17 February 2025
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 40 (2) , 275-285
Development of handsheet mechanical properties linked to fibre distributions in two-stage low consistency refining of high yield pulp
In this study, a two-stage, low-consistency (LC) refining process at the Holmen Braviken paper mill in Sweden was examined to evaluate the relationship between energy input, fibre distributions, and pulp properties, including handsheet properties. The LC refiners used thermo-mechanical pulp based on 100 % Norway spruce, with two specific energy levels: “low” (≈80 kWh/adt) or “high” (≈100 kWh/adt). All four permutations of these settings were examined. Overall, higher refining efficiency (measured by the increase in tensile index per applied energy) was observed in the first LC refiner stage than in the second. To further explore the impact of LC refining, pulp particle distributions were investigated. Samples from before, between and after the two LC stages were analysed using an optical fibre analyser, which provided detailed data on length-width-curl-fibrillation distributions. The impact of LC refining on these distributions was quantified using Kolmogorov-Smirnov statistics, highlighting statistically significant changes observed in the length and curl distributions. We investigated the correlation between energy input into the LC refiners and the impact on fibre distributions and handsheet properties. These insights underscore the effectiveness of our analytical approach and its potential for refining process control in mechanical pulping, offering a method for more targeted and efficient adjustments.
- 17 February 2025
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 40 (2) , 275-285
Open AccessDevelopment of handsheet mechanical properties linked to fibre distributions in two-stage low consistency refining of high yield pulp
In this study, a two-stage, low-consistency (LC) refining process at the Holmen Braviken paper mill in Sweden was examined to evaluate the relationship between energy input, fibre distributions, and pulp properties, including handsheet properties. The LC refiners used thermo-mechanical pulp based on 100 % Norway spruce, with two specific energy levels: “low” (≈80 kWh/adt) or “high” (≈100 kWh/adt). All four permutations of these settings were examined. Overall, higher refining efficiency (measured by the increase in tensile index per applied energy) was observed in the first LC refiner stage than in the second. To further explore the impact of LC refining, pulp particle distributions were investigated. Samples from before, between and after the two LC stages were analysed using an optical fibre analyser, which provided detailed data on length-width-curl-fibrillation distributions. The impact of LC refining on these distributions was quantified using Kolmogorov-Smirnov statistics, highlighting statistically significant changes observed in the length and curl distributions. We investigated the correlation between energy input into the LC refiners and the impact on fibre distributions and handsheet properties. These insights underscore the effectiveness of our analytical approach and its potential for refining process control in mechanical pulping, offering a method for more targeted and efficient adjustments.
- Open Access
- 19 November 2024
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 40 (1) , 107-112
Energy consumption in refiner mechanical pulping
The efficiency of mechanical pulping has long been of interest due to the large energy consumed by the process. Previous estimates of theoretical efficiency have accounted for less than 20 % of the energy employed. In this study, we make new estimates based on fracture mechanics and abrasion as the mechanisms of new surface creation. We postulate that fracture mechanics comminutes wood into fibres and creates pores in fibre walls. This consumes around 100 kWh/t. Abrasion peels surface material from fibres in the form of morphologically different fines particles. Based on abrasion theory, we estimate this specific energy to be around 1,330 kWh/t. Together, fracture mechanics and abrasion, account for about 70 % of the specific energy (2,000 kWh/t) to produce TMP for printing paper grades. We postulate that the remaining energy is consumed as hysteresis losses from viscoelastic strains not linked to creation of new surface. The largest single source of energy consumption, abrasion, alone accounts for about 66 % of the energy of the process. Finally, we discuss how energy may be reduced by refining intensity and other means.
- 19 November 2024
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 40 (1) , 107-112
Open AccessEnergy consumption in refiner mechanical pulping
The efficiency of mechanical pulping has long been of interest due to the large energy consumed by the process. Previous estimates of theoretical efficiency have accounted for less than 20 % of the energy employed. In this study, we make new estimates based on fracture mechanics and abrasion as the mechanisms of new surface creation. We postulate that fracture mechanics comminutes wood into fibres and creates pores in fibre walls. This consumes around 100 kWh/t. Abrasion peels surface material from fibres in the form of morphologically different fines particles. Based on abrasion theory, we estimate this specific energy to be around 1,330 kWh/t. Together, fracture mechanics and abrasion, account for about 70 % of the specific energy (2,000 kWh/t) to produce TMP for printing paper grades. We postulate that the remaining energy is consumed as hysteresis losses from viscoelastic strains not linked to creation of new surface. The largest single source of energy consumption, abrasion, alone accounts for about 66 % of the energy of the process. Finally, we discuss how energy may be reduced by refining intensity and other means.
- 18 September 2024
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 39 (4) , 575-585
Development of fibre properties in mill scale: high- and low consistency refining of thermomechanical pulp (part 2) – Importance of fibre curl
Increased knowledge on the correlation between pulp processing, fibre-properties and paper properties is required to improve fibre-based products. Part 1 of this investigation deals with the effects of HC and LC refining on fibre properties development. LC refining reduced curl and increased tensile index in a manner similar to hot disintegration whereas HC refining increased curl slightly. In this second part, the correlation between fibre curl and handsheet properties of thermomechanical pulp, subjected to low consistency (LC) refining and hot/cold disintegration is examined. Fibre curl decreased by laboratory disintegration and LC refining and showed a linear correlation with increased tensile index and tensile stiffness. Evaluation of fibre property distributions gave a more detailed description of the development of fibre properties. These revealed that disintegration and LC refining gave different fibre curl versus fibre length distributions, even when their average values were similar. These results confirm that analysing fibre property distributions contributes to a more detailed knowledge of the development of pulp quality. Hot disintegration before laboratory testing exaggerated pulp quality and increase internal fibrillation and can therefore be questioned. When hot disintegration is performed before pulp analyses, the impact of LC refining on paper properties may be misjudged.
- 18 September 2024
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 39 (4) , 575-585
Development of fibre properties in mill scale: high- and low consistency refining of thermomechanical pulp (part 2) – Importance of fibre curl
Increased knowledge on the correlation between pulp processing, fibre-properties and paper properties is required to improve fibre-based products. Part 1 of this investigation deals with the effects of HC and LC refining on fibre properties development. LC refining reduced curl and increased tensile index in a manner similar to hot disintegration whereas HC refining increased curl slightly. In this second part, the correlation between fibre curl and handsheet properties of thermomechanical pulp, subjected to low consistency (LC) refining and hot/cold disintegration is examined. Fibre curl decreased by laboratory disintegration and LC refining and showed a linear correlation with increased tensile index and tensile stiffness. Evaluation of fibre property distributions gave a more detailed description of the development of fibre properties. These revealed that disintegration and LC refining gave different fibre curl versus fibre length distributions, even when their average values were similar. These results confirm that analysing fibre property distributions contributes to a more detailed knowledge of the development of pulp quality. Hot disintegration before laboratory testing exaggerated pulp quality and increase internal fibrillation and can therefore be questioned. When hot disintegration is performed before pulp analyses, the impact of LC refining on paper properties may be misjudged.
- Open Access
- 13 April 2021
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (9) , 824-837
Fibre development in an intensified mechanical pulping process
Mechanical pulp for printing paper can be produced with a process that involve much less equipment and that require much lower specific energy compared to conventional processes. Even though common evaluation methods, e.g. handsheet testing, have shown that the pulp quality is similar for the simplified and the conventional processes, it is not known how fibre properties, at the microscopic level, is developed with the simplified process. In this mill scale study, the fibre properties attained with an “intensified” mechanical pulping process, consisting of single stage high consistency double disc refining followed by two stage low consistency refining and no reject treatment was investigated. The simplified process was compared to a process with a reject system. The simplified process rendered fibres with higher degree of fibrillation, higher share of axial splits, lower fibre wall thickness but slightly lower length than the conventional process. The fibrillar fines size distribution of the two processes was different. The conventional process generated more of small fibrillar fines which probably explains the higher tensile index at given density for that process. The results show that it is possible to simplify the production process for mechanical pulp and reduce the specific energy with over 700 kWh/adt.
- 13 April 2021
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (9) , 824-837
Open AccessFibre development in an intensified mechanical pulping process
Mechanical pulp for printing paper can be produced with a process that involve much less equipment and that require much lower specific energy compared to conventional processes. Even though common evaluation methods, e.g. handsheet testing, have shown that the pulp quality is similar for the simplified and the conventional processes, it is not known how fibre properties, at the microscopic level, is developed with the simplified process. In this mill scale study, the fibre properties attained with an “intensified” mechanical pulping process, consisting of single stage high consistency double disc refining followed by two stage low consistency refining and no reject treatment was investigated. The simplified process was compared to a process with a reject system. The simplified process rendered fibres with higher degree of fibrillation, higher share of axial splits, lower fibre wall thickness but slightly lower length than the conventional process. The fibrillar fines size distribution of the two processes was different. The conventional process generated more of small fibrillar fines which probably explains the higher tensile index at given density for that process. The results show that it is possible to simplify the production process for mechanical pulp and reduce the specific energy with over 700 kWh/adt.
- Open Access
- 13 April 2021
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 36 (3) , 425-434
Energy efficiency in mechanical pulping – definitions and considerations
Production of mechanical pulps requires high specific electrical energy compared to many other attrition processes. In Scandinavia, the lowest specific refining energy for production of thermomechanical pulp is around 1800 kWh/t for newsprint quality, which is roughly 60 times higher than for crushing of stone to a similar size distribution. The high specific energy demand for refining has naturally motivated large efforts in the search for improved efficiency. It is always practical to be able to quantify improvements in efficiency for comparison of process designs and of different machine types. However, there is no commonly accepted definition of efficiency for mechanical pulping processes. In published work within mechanical pulping, energy efficiency has been presented in different ways. In this paper, we discuss definitions of energy efficiency and aspects that ought to be considered when energy efficiency is presented. Although focus of this work is on energy efficiency for refiner processes, the principles can be applied to other types of mechanical pulping processes such as stone groundwood.
- 13 April 2021
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 36 (3) , 425-434
Open AccessEnergy efficiency in mechanical pulping – definitions and considerations
Production of mechanical pulps requires high specific electrical energy compared to many other attrition processes. In Scandinavia, the lowest specific refining energy for production of thermomechanical pulp is around 1800 kWh/t for newsprint quality, which is roughly 60 times higher than for crushing of stone to a similar size distribution. The high specific energy demand for refining has naturally motivated large efforts in the search for improved efficiency. It is always practical to be able to quantify improvements in efficiency for comparison of process designs and of different machine types. However, there is no commonly accepted definition of efficiency for mechanical pulping processes. In published work within mechanical pulping, energy efficiency has been presented in different ways. In this paper, we discuss definitions of energy efficiency and aspects that ought to be considered when energy efficiency is presented. Although focus of this work is on energy efficiency for refiner processes, the principles can be applied to other types of mechanical pulping processes such as stone groundwood.
- Open Access
- 5 November 2019
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 35 (1) , 1-17
On the development of the refiner mechanical pulping process – a review
This paper is a review of the development of the mechanical pulping process with focus on refiner-based processes. The intention is to provide an overview of the trends and the major advances in the development of the mechanical pulping (MP) process. The focus is on the development of the entire MP process, rather than the refiner as such. However, when discussing the MP process development, it is inevitable to consider the development of the refiner unit operation briefly. Processes for printing papers based on softwood is mainly discussed, but board processes are discussed briefly as well.
- 5 November 2019
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 35 (1) , 1-17
Open AccessOn the development of the refiner mechanical pulping process – a review
This paper is a review of the development of the mechanical pulping process with focus on refiner-based processes. The intention is to provide an overview of the trends and the major advances in the development of the mechanical pulping (MP) process. The focus is on the development of the entire MP process, rather than the refiner as such. However, when discussing the MP process development, it is inevitable to consider the development of the refiner unit operation briefly. Processes for printing papers based on softwood is mainly discussed, but board processes are discussed briefly as well.
- 1 February 2019
- Published by BioResources in BioResources
- Vol. 14 (1) , 882-894
Low Consistency Refining Combined with Screen Fractionation: Reduction of Mechanical Pulping Process Complexity
- 1 February 2019
- Published by BioResources in BioResources
- Vol. 14 (1) , 882-894
Low Consistency Refining Combined with Screen Fractionation: Reduction of Mechanical Pulping Process Complexity