Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Fanglin Huang has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Performance Analysis of Ferronickel Slag-Ordinary Portland Cement Pervious Concrete

    by Zhongping Tang, Hua Peng, Pingbo Mei, Fanglin Huang, Shixiang Yi, Fan Feng

    It is unknown whether Ferronickel slag (FNS)-ordinary Portland cement (OPC)-based pervious concrete (FOPC) is feasible. To this end, a feasibility study was conducted on FOPC. Firstly, a detailed microscopic examination of the FNS powder was conducted, encompassing analyses of its particle size distribution, SEM, EDS, and chemical composition. These analyses aimed to establish the suitability of a composite of FNS and OPC as a composite cementitious material. Subsequent experimentation focused on evaluating the compressive strength of the composite paste material with varying mixed proportions, revealing a slight reduction in strength as the FNS substitution rate increased. Furthermore, the study designed eighteen different mix proportions of FOPC to investigate the key physical properties, including porosity, density, compressive strength, and the coefficient of permeability. Findings indicated that increases in the cementitious material proportion correlate with enhanced concrete strength, where the ratio of cementitious to aggregate increased by 6.7% and 16.5%, and the strength of FOPC increased by 10–13% and 30–50%, respectively. Conversely, a rise in the FNS substitution rate led to a reduction in compressive strength across different mix ratios. Additionally, the ratio of paste material to aggregate was found to significantly influence the permeability coefficient. These comprehensive performance evaluations suggest that incorporating FNS into OPC for pervious concrete applications is a feasible approach, offering valuable insights for the promotion of waste reuse and the advancement of energy conservation and emissions reduction efforts.


  • Open Access

    Design and Optimization of the Bi-Directional U-Ribbed Stiffening Plate–Concrete Composite Bridge Deck Structure

    by Dingchao Wei, Jingwen Liao, Jianjun Liu, Yingjie Gao, Fanglin Huang

    The steel–concrete composite structure is widely used in civil engineering for large-span bridges. Orthotropic steel bridge decks (OSDs) have particularly gained popularity due to their excellent mechanical performance. To address cracking issues in OSDs and concrete in negative moment regions, a novel bi-directional U-ribbed stiffening plate (BUSP)–concrete composite bridge deck is proposed. By using finite element analysis, the mechanical performance is evaluated based on maximum tensile stress and vertical displacement of concrete overlays. Results show that the BUSP–concrete deck outperformed conventional flat decks. It is also found that increasing the height, thickness, and opening width of U-ribs reduced tensile stress and maximum displacement. Adjusting height had the most significant effect on displacement while opening width affected tensile stress the most. Considering material usage, optimizing height is proved to be more effective than adjusting thickness and opening width. Decreasing spacing parameters improved performance but added complexity and reduced construction convenience. These findings will guide the design and optimization of steel–concrete composite bridge deck structures.


  • Open Access

    Study on Temperature-Dependent Uniaxial Tensile Tests and Constitutive Relationship of Modified Polyurethane Concrete

    by Yanqun Han, Xiandong Meng, Fan Feng, Xuming Song, Fanglin Huang, Weibin Wen

    Modified polyurethane concrete (MPUC) is a new material for steel deck pavements. In service, the pavement is often cracked due to excessive tensile stress caused by temperature changes. In order to study the tensile properties of MPUC in the diurnal temperature range of steel decks, uniaxial tensile tests of MPUC were carried out at five temperatures. Three kinds of specimens and a novel fixture were designed and fabricated to compare the results of four different tensile test methods. The deformation of the specimen was collected synchronously by two methods: pasting strain gauge and digital image correlation (DIC) technique. Based on the experiment, the tensile mechanical properties, failure modes, and constitutive relations of MPUC were studied under the effect of temperature. The research results show that the novel fixture can avoid stress concentration. By observing the fracture surface of the specimens, the bonding performance is great between the binder and the aggregate at different temperatures. The tensile strength and elastic modulus of MPUC decrease with increasing temperatures, while the fracture strain, and fracture energy increase with increasing temperatures. The formulas of temperature-dependent tensile strength, fracture strain, and elastic modulus of MPUC were established, and the constitutive relationship of MPUC is further constructed in the rising stage under uniaxial tension. The calculation results show good agreement with experimental ones.


  • Open Access

    Enhanced Ultimate Shear Capacity of Concave Square Frustum-Shaped Wet Joint in Precast Steel–Concrete Composite Bridges

    by Fan Feng, Fanglin Huang, Weibin Wen, Peng Ge, Yong Tao

    Wet joints are widely used in precast steel–concrete composite bridges to accelerate the construction of bridges, though a conventional wet joint usually has a poor ultimate shear capacity. To improve the shear capacity of the wet joint, a concave square frustum-shaped wet joint was proposed, and the failure modes and ultimate shear capacity were studied experimentally and numerically. Specimens with concave square frustum-shaped and conventional wet joints (labeled as S-SWJ and S-CWJ) were fabricated, and experiments were performed on them. The results showed that the ultimate shear capacity of S-SWJ was substantially enhanced compared to that of S-CWJ. To further explore the ultimate shear capacity of S-SWJ, the failure modes and the influences of concrete strength and shear key angle on the ultimate shear capacity were studied using a validated finite element (FE) model. Based on the FE analysis, the guidelines for obtaining a wet joint with desirable shear capacity are presented, which is useful for the design of wet joints with high ultimate shear capacity.


  • Open Access

    Evaluating the Dynamic Response of the Bridge‐Vehicle System considering Random Road Roughness Based on the Moment Method

    by Fan Feng, Fanglin Huang, Weibin Wen, Zhe Liu, Xiang Liu

    The bridge‐vehicle interaction (BVI) system vibration is caused by the vehicles passing through the bridge. The road roughness has a great impact on the system vibration. In this regard, poor road roughness is known to affect the comfort of the vehicle crossing the bridge and aggravate the fatigue damage of the bridge. Road roughness is usually regarded as a random process in numerical calculation. To fully consider the influence of road roughness randomness on the response of the BVI system, a random BVI model was established. Thereafter, the random process of road roughness was expressed by Karhunen–Loeve expansion (KLE), after which the moment method was used to calculate the maximum probability value of the BVI system response. The proposed method has higher accuracy and efficiency than the Monte Carlo simulation (MCS) calculation method. Subsequently, the influences of vehicle speed, roughness grade, and bridge span on the impact factor (IMF) were analyzed. The results show that the road roughness grade has a greater impact on the bridge IMF than the bridge span and vehicle speed.


  • Open Access

    Characterization of Air Void in Porous Asphalt Mixture Using Image Techniques and Permeability Test

    by Zhongping Tang, Fanglin Huang

    In this study, air void contents and distributions of porous asphalt mixtures along the vertical and horizontal directions were quantitatively measured on planar images. Air void contents were determined using some image techniques; while the permeability was measured by the falling head test. Two aggregate gradations (G1 and G2) and three blow numbers (30, 40, and 50) were chosen to explore the effects of gradation and compaction effort on the porosity and permeability. Results showed that porosities and permeabilities are symmetrically distributed along the middle of the specimens; the porosities and permeabilities got the minimum values around the middle zone. A finer gradation or a significant compaction effort generally led to a lower porosity and permeability coefficient. In the horizontal direction, the air void content showed an increasing trend from the outside layer to the inner layer, indicating the nonuniformity of porosity distribution.


  • Open Access

    Mode I Fracture Behaviors between Cement Concrete and Asphalt Concrete Layer

    by Zhongping Tang, Fanglin Huang, Hua Peng

    Asphalt overlay or concrete overlay on existing pavements is a common strategy for pavement maintenance. Interlayer bonding performance between asphalt and concrete layers is a critical concern in achieving optimal long‐term structural performance due to the possible cracking along the interface. In this study, bonding behaviors of asphalt concrete interface were characterized by employing mode I fracture tests conducted at −10 and 25°C, respectively. Two typical interface conditions were manually prepared. A tack coat material was applied on the interface with four distinct rates: 0.1, 0.2, 0.3, and 0.4 L/m2. Parameters including fracture strength, stress intensity factor (KIC), facture energy (GF), and energy release rate (J integral) were selected to evaluate the fracture performance. Results showed that optimum tack coat rates were 0.1 and 0.3 L/m2 for specimens with unmilled and milled surfaces. At the optimum tack coat rates, KIC and GF increased with the increase of interface roughness at −10°C, while, at 25°C, J integral of specimens with unmilled interface was larger than that of specimens with milled interface at the optimum tack coat rates. Analysis of variance (ANOVA) was conducted to evaluate the significance of the factors on the fracture loads and found that surface roughness is significant at −10°C and becomes nonsignificant at 25°C. Temperature and tack coat rate were significant factors considering a given interface.


  • Open Access

    Breast Cancer Image Classification via Multi-Network Features and Dual-Network Orthogonal Low-Rank Learning

    by Yongjun Wang, Baiying Lei, Ahmed Elazab, Ee-Leng Tan, Wei Wang, Fanglin Huang, Xuehao Gong, Tianfu Wang

    Histopathological image analysis is an important technique for early diagnosis and detection of breast cancer in clinical practice. However, it has limited efficiency and thus the detection of breast cancer is still an open issue in medical image analysis. To improve the early diagnostic accuracy of breast cancer and reduce the workload of doctors, we devise a classification framework based on histology images by combining deep learning with machine learning methodologies in this paper. Specifically, we devise a multi-network feature extraction model by using pre-trained deep convolution neural networks (DCNNs), develop an effective feature dimension reduction method and train an ensemble support vector machine (E-SVM). First, we preprocess the histological images via scale transformation and color enhancement methods. Second, the multi-network features are extracted by using four pre-trained DCNNs (e.g., DenseNet-121, ResNet-50, multi-level InceptionV3, and multi-level VGG-16). Third, a feature selection method via dual-network orthogonal low-rank learning (DOLL) is further developed for performance boosting and overfitting alleviation. Finally, an E-SVM is trained via fused features and voting strategy to perform the classification task, which classifies the images into four classes (i.e., benign, in situ carcinomas, invasive carcinomas, and normal). We evaluate the proposed method on the public ICIAR 2018 Challenge dataset of histology images of breast cancer and achieve a high classification accuracy of 97.70%. Experimental results show that our method can achieve quite promising performance and outperform state-of-the-art methods.