John Holmes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
John Holmes has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Paul Compston
6 shared publications- Raj Das
RMIT University
5 shared publications Zbigniew Stachurski
5 shared publications- Silvano Sommacal
Department of Materials Physics, Research School of Physics, Australian National University, Canberra, Australia
4 shared publications Klaus Drechsler
2 shared publications- Benno Böckl
School of Engineering & Design, Department of Aerospace and Geodesy, Chair of Carbon Composites, Technical University of Munich, Germany
1 shared publication
Latest Publications
- Open Access
- 1 October 2024
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 12 (10) , 4289-4310
Mechanistic investigation of highly bendable magnesium alloy sheet fabricated by short-process manufacturing
- 1 October 2024
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 12 (10) , 4289-4310
Open AccessMechanistic investigation of highly bendable magnesium alloy sheet fabricated by short-process manufacturing
- Open Access
- 23 September 2024
- Published by Elsevier in Composite Structures
- Vol. 351
X-ray micro-computed tomography for mechanical behaviour analysis of Automated Fiber Placement (AFP) laminates with integrated gaps and overlaps
- 23 September 2024
- Published by Elsevier in Composite Structures
- Vol. 351
Open AccessX-ray micro-computed tomography for mechanical behaviour analysis of Automated Fiber Placement (AFP) laminates with integrated gaps and overlaps
- Open Access
- 18 July 2024
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 38 (3) , 1257-1274
Using carbon fiber tape to tailor the coefficient of thermal expansion in 3D-Printed composite tooling
In this work, we investigated the effect of plain woven carbon fiber tape embedded in each layer of an additively manufactured part on the coefficient of thermal expansion (CTE) and compared it to conventionally printed parts. Current advancements in Additive Manufacturing enable cost-efficient 3D printing of composite tools. However, these tools do not yet offer a low CTE comparable to Invar, necessary for producing aerospace-quality composite parts. Using the novel Advanced Tape Layer Additive Manufacturing process, the tape is placed on top of the bead immediately after extruding the short fiber-reinforced material. The samples are compared to Material Extrusion specimens from a Large Format Additive Manufacturing System. A lower CTE was achieved within the printing plane. Micro-computed tomography images correlate the preferential orientation of short fibers with measured CTE values. The CTE modification can match the part CTE to the tool CTE and therefore optimize the quality of manufactured parts.
- 18 July 2024
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 38 (3) , 1257-1274
Open AccessUsing carbon fiber tape to tailor the coefficient of thermal expansion in 3D-Printed composite tooling
In this work, we investigated the effect of plain woven carbon fiber tape embedded in each layer of an additively manufactured part on the coefficient of thermal expansion (CTE) and compared it to conventionally printed parts. Current advancements in Additive Manufacturing enable cost-efficient 3D printing of composite tools. However, these tools do not yet offer a low CTE comparable to Invar, necessary for producing aerospace-quality composite parts. Using the novel Advanced Tape Layer Additive Manufacturing process, the tape is placed on top of the bead immediately after extruding the short fiber-reinforced material. The samples are compared to Material Extrusion specimens from a Large Format Additive Manufacturing System. A lower CTE was achieved within the printing plane. Micro-computed tomography images correlate the preferential orientation of short fibers with measured CTE values. The CTE modification can match the part CTE to the tool CTE and therefore optimize the quality of manufactured parts.
- Top Cited PapersOpen Access
- 31 March 2023
- Published by Elsevier in Composite Structures
- Vol. 315
Digital image and volume correlation for deformation and damage characterisation of fibre-reinforced composites: A review
- 31 March 2023
- Published by Elsevier in Composite Structures
- Vol. 315
Top Cited PapersOpen AccessDigital image and volume correlation for deformation and damage characterisation of fibre-reinforced composites: A review
- 1 January 2022
- Published by Elsevier in Composites Communications
- Vol. 29
3D topographical analysis for defect detection during loading of woven thermoplastic composites
- 1 January 2022
- Published by Elsevier in Composites Communications
- Vol. 29
3D topographical analysis for defect detection during loading of woven thermoplastic composites
- 1 May 2020
- Published by Elsevier in Composites Part B: Engineering
- Vol. 188
Surface topography evolution of woven thermoplastic composites under deformation
- 1 May 2020
- Published by Elsevier in Composites Part B: Engineering
- Vol. 188
Surface topography evolution of woven thermoplastic composites under deformation