JMJ. Adin Mann

J. Adin Mann

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


J. Adin Mann has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Line tension and line entropy associated with the monolayer/trilayer boundary of smectic liquid crystal at the air-water interface

    by Huda A. Alwusaydi, Joseph S. Yarzebinski, Pritam Mandal, J. Adin Mann, Elizabeth K. Mann

    Molecularly thin films of the smectic liquid crystal 4'-octyl-4-biphenylcarbonitrile (8CB) at the air-water interface phase separate into regions with different numbers of layers, in analogy with freestanding smectic liquid crystalline films. This paper reports the line tension associated with the boundary of coexisting trilayer and monolayer phases of in Langmuir films of 8CB at the air-water interface as a function of temperature and humidity and infers information on the boundary profile between the coexisting phases. Two complementary techniques are used to characterize the 8CB thin films: surface pressure-area isotherm and Brewster angle microscopy (BAM). We determine the line tension by stretching isolated domains from their equilibrium circular shape and analyzing the free relaxation with a hydrodynamic model. Then, we interpret the line tension vs temperature data in terms of an excess line entropy for the domain boundary, which requires careful consideration of the thermodynamics of inhomogeneous monolayer systems.

  • Open Access

    Robust surface light scattering spectroscopy for fluid interfaces

    by Angelo S Visco, Alan R Baldwin, Alexander I Belgovskiy, J Adin Mann, William V Meyer, Anthony E Smart, Nabin K Thapa, Elizabeth K Mann

    Surface Light Scattering Spectroscopy (SLSS) can characterize the dynamics of an interface between two immiscible fluids by measuring the frequency spectrum of coherent light scattered from thermophysical fluctuations—‘ripplons’. In principle, and for many interfaces, SLSS can simultaneously measure surface tension and viscosity, with the potential for higher-order properties, such as surface elasticity and bending moments. Previously, this has been challenging. We describe and present some measurements from an instrument with improvements in optical design, specimen access, vibrational stability, signal-to-noise ratio, electronics, and data processing. Quantitative improvements include total internal reflection at the interface to enhance the typically available signal by a factor of order 40 and optical improvements that minimize adverse effects of sloshing induced by external vibrations. Information retrieval is based on a comprehensive surface response function, an instrument function, which compensates for real geometrical and optical limitations, and processing of almost real-time data to report results and their likely accuracy. Detailed models may be fit to the power spectrum in real time. The raw one-dimensional digitized data stream is archived to allow post-experiment processing. This paper reports a system design and implementation that offers substantial improvements in accuracy, simplicity, ease of use, and cost. The presented data are for systems in regions of low viscosity where the ripplons are underdamped, but the hardware described is more widely applicable.


  • Comparison of Candidate Steady Loading Elevated Temperature Design-by-Analysis Methods

    by David Dewees, J. Adin Mann, Chithranjan Nadarajah, Mark Messner, Ben Hantz, David Andersen

    Design-by-Analysis is distinguished from Design-by-Formula or Design-by-Rule in that specific failure modes are identified, and detailed analysis of each failure mode is compared to criteria specific to each failure mode. Several ASME Boiler and Pressure Vessel code committees continue to work on design-by-analysis methods in the elevated temperature range, where creep rupture is a failure mode with steady loading. The Subgroup on Elevated Temperature Design, which reports to Section I and Section VIII and collaborates with Section III, has been evaluating eight different analysis methods for six example problems. The two Design-by-Formula methods are from Section I and Section VIII Division 1 and the Design-by-Analysis methods are (1) Linear Elastic Analysis with revised stress limits, (2) Isochronous Curve Limit Load, (3) STP-PT-070 Limit Load Analysis, (4) Detailed Inelastic Methods using the MPC Omega creep models, (5) ASME CC2843 (simplified NH method),and (6) Section III Division 5 Draft Code Case for Limit Load Analysis. The test cases include (1) Grade 11 Steam Outlet Header, (2) Grade 91 Header Endplate, (3) Grade 91 Steam Outlet Header, (4) Grade 91 Steam outlet Header 2, (5) Grade 91 Steam Piping Lateral and (6) Type 304 Stainless Spherical Vessel/Nozzle. To ensure a common comparison, a common material definition was used based on the ASME FFS-1/API579 material models. Each of the analysis methods and examples will be described along with a comparison of the maximum pressure predicted by each method for each problem.

  • Interfacial tension and mechanism of liquid–liquid phase separation in aqueous media

    by Amber R. Titus, Luisa A. Ferreira, Alexander I. Belgovskiy, Edgar E. Kooijman, Elizabeth K. Mann, J. Adin Mann, William V. Meyer, Anthony E. Smart, Vladimir N. Uversky, Boris Y. Zaslavsky

    The organization of multiple subcellular compartments is controlled by liquid–liquid phase separation.


  • Gasous Hole Closing in a Polymer Langmuir Monolayer

    by Lu Zou, Andrew J. Bernoff, J. Adin Mann, James C. Alexander, Elizabeth K. Mann

    The hole-closing phenomenon is studied in a polymer Langmuir film with coexisting gaseous and liquid phases both as a test of hydrodynamic theories of a two-dimensional fluid embedded in a three-dimensional one and as a means to accurately determine line tension, an important parameter determining size, shape, and dynamics within these and other membrane model systems. The hole-closing curve consists of both a universal linear regime and a history-dependent nonlinear one. Improved experimental technique allows us to explore the origin of the nonlinear regime. The linear regime confirms previous theoretical work and yields a value lambda = (0.69 +/- 0.02) pN for the line tension of the boundary between the gaseous and liquid phases. The observed hole closing also demonstrates that the two-dimensional polymer gas must be taken as having a small, probably negligible elasticity, so that line-tension measurements assuming that both phases are incompressible should be re-evaluated.


  • Measuring the roughness of interfaces

    by J.A. Mann, E.M. Rains, W.A. Woyczynski