Pai-Ying Liao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pai-Ying Liao has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Mengwei Si
National Key Laboratory of Advanced Micro and Nano Manufacture Technology, Shanghai Jiao Tong University, Shanghai, China
7 shared publications - Peide D. Ye
Elmore Family School of Electrical and Computer Engineering, Purdue University, West Lafayette, USA
6 shared publications - Zhuocheng Zhang
School of Electrical and Computer Engineering, Purdue University, West Lafayette, IN, USA
5 shared publications Ali Shakouri
School of Electrical and Computer Engineering and the Birck Nanotechnology Center, Purdue University, West Lafayette, IN, USA
3 shared publications- Sami Alajlouni
School of Electrical and Computer Engineering and the Birck Nanotechnology Center, Purdue University, West Lafayette, IN, USA
3 shared publications - Zehao Lin
Elmore Family School of Electrical and Computer Engineering, Purdue University, West Lafayette, IN, USA
3 shared publications
Latest Publications
- 8 April 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124  (15)
Reduced temperature in lateral (AlxGa1−x)2O3/Ga2O3 heterojunction field effect transistor capped with nanocrystalline diamond
The low thermal conductivity of β-Ga2O3 is a significant concern for maximizing the potential of this ultra-wide bandgap semiconductor as a power switching device technology. Here, we report on the use of nanocrystalline diamond (NCD) deposited via microwave plasma enhanced chemical vapor deposition (MP-CVD) as a top-side, device-level thermal management solution on a lateral β-Ga2O3 transistor. NCD was grown via MP-CVD on β-(AlxGa1−x)2O3/β-Ga2O3 heterostructures prior to the gate formation of the field-effect transistor. A reduced growth temperature of 400 °C and a SiNx barrier layer were used to protect the oxide semiconductors from etching in the MP-CVD H2 plasma environment. Raman spectroscopy showed a highly sp3-bonded NCD film was obtained at 400 °C, with grain size of about 50–100 nm imaged via atomic force microscopy. The incorporation of the NCD heat-spreading layer resulted in a β-(AlxGa1−x)2O3/β-Ga2O3 heterostructure field-effect transistor showing a decrease in the total thermal resistance at the gate by 42%. The fabrication process, including the NCD etch in the gate region, will need to be improved to minimize the impact of these processes on important device characteristics (i.e., drain current, threshold voltage, and leakage current).
- 8 April 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124  (15)
Reduced temperature in lateral (AlxGa1−x)2O3/Ga2O3 heterojunction field effect transistor capped with nanocrystalline diamond
The low thermal conductivity of β-Ga2O3 is a significant concern for maximizing the potential of this ultra-wide bandgap semiconductor as a power switching device technology. Here, we report on the use of nanocrystalline diamond (NCD) deposited via microwave plasma enhanced chemical vapor deposition (MP-CVD) as a top-side, device-level thermal management solution on a lateral β-Ga2O3 transistor. NCD was grown via MP-CVD on β-(AlxGa1−x)2O3/β-Ga2O3 heterostructures prior to the gate formation of the field-effect transistor. A reduced growth temperature of 400 °C and a SiNx barrier layer were used to protect the oxide semiconductors from etching in the MP-CVD H2 plasma environment. Raman spectroscopy showed a highly sp3-bonded NCD film was obtained at 400 °C, with grain size of about 50–100 nm imaged via atomic force microscopy. The incorporation of the NCD heat-spreading layer resulted in a β-(AlxGa1−x)2O3/β-Ga2O3 heterostructure field-effect transistor showing a decrease in the total thermal resistance at the gate by 42%. The fabrication process, including the NCD etch in the gate region, will need to be improved to minimize the impact of these processes on important device characteristics (i.e., drain current, threshold voltage, and leakage current).
- 16 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70  (4) , 2052-2058
Transient Thermal and Electrical Co-Optimization of BEOL Top-Gated ALD In2O3 FETs Toward Monolithic 3-D Integration
In this work, the transient thermal and electrical characteristics of top-gated (TG), ultrathin, atomic-layer-deposited (ALD), back-end-of-line (BEOL) compatible indium oxide (In2O3) transistors on various thermally conductive substrates are co-optimized by visualization of the self-heating effect (SHE) utilizing an ultrafast high-resolution (HR) thermo-reflectance (TR) imaging system and overcome the thermal challenges through substrate thermal management and short-pulse measurement. At the steady-state, the temperature increase ($\Delta {T}$ ) of the devices on highly resistive silicon (HR Si) and diamond substrates are roughly 6 and 13 times lower than that on a SiO2/Si substrate, due to the much higher thermal conductivities ($\kappa $ ) of HR Si and diamond. Consequently, the ultrahigh drain current (${I}_{D}$ ) of 3.7 mA/$\mu \text{m}$ at drain voltage (${V}_{\text {DS}}$ ) of 1.4 V with direct current (dc) measurement is achieved with TG ALD In2O3 FETs on a diamond substrate. Furthermore, transient thermal study shows that it takes roughly 350 and 300 ns for the devices to heat-up and cool-down to the steady-states, being independent of the substrate. The extracted thermal time constants of heat-up ($\tau _{h}$ ) and cool-down ($\tau _{c}$ ) processes are 137 and 109 ns, respectively. By employing electrical short-pulse measurement with a pulsewidth (${t}_{\text {pulse}}$ ) shorter than$\tau _{h}$ , the SHE can be significantly reduced. Accordingly, a higher${I}_{D}$ of 4.3 mA/$\mu \text{m}$ is realized with a 1.9-nm-thick In2O3 FET on HR Si substrate after co-optimization. Besides, to integrate BEOL-compatible ALD In2O3 transistors on the front-end-of-line (FEOL) devices with the maintenance of the satisfactory heat dissipation capability, a FEOL-interlayer-BEOL structure is proposed where the interlayer not only electrically isolates the FEOL and BEOL devices but also serves as a thermally conductive layer to alleviate the SHE.- 16 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70  (4) , 2052-2058
Transient Thermal and Electrical Co-Optimization of BEOL Top-Gated ALD In2O3 FETs Toward Monolithic 3-D Integration
In this work, the transient thermal and electrical characteristics of top-gated (TG), ultrathin, atomic-layer-deposited (ALD), back-end-of-line (BEOL) compatible indium oxide (In2O3) transistors on various thermally conductive substrates are co-optimized by visualization of the self-heating effect (SHE) utilizing an ultrafast high-resolution (HR) thermo-reflectance (TR) imaging system and overcome the thermal challenges through substrate thermal management and short-pulse measurement. At the steady-state, the temperature increase ($\Delta {T}$ ) of the devices on highly resistive silicon (HR Si) and diamond substrates are roughly 6 and 13 times lower than that on a SiO2/Si substrate, due to the much higher thermal conductivities ($\kappa $ ) of HR Si and diamond. Consequently, the ultrahigh drain current (${I}_{D}$ ) of 3.7 mA/$\mu \text{m}$ at drain voltage (${V}_{\text {DS}}$ ) of 1.4 V with direct current (dc) measurement is achieved with TG ALD In2O3 FETs on a diamond substrate. Furthermore, transient thermal study shows that it takes roughly 350 and 300 ns for the devices to heat-up and cool-down to the steady-states, being independent of the substrate. The extracted thermal time constants of heat-up ($\tau _{h}$ ) and cool-down ($\tau _{c}$ ) processes are 137 and 109 ns, respectively. By employing electrical short-pulse measurement with a pulsewidth (${t}_{\text {pulse}}$ ) shorter than$\tau _{h}$ , the SHE can be significantly reduced. Accordingly, a higher${I}_{D}$ of 4.3 mA/$\mu \text{m}$ is realized with a 1.9-nm-thick In2O3 FET on HR Si substrate after co-optimization. Besides, to integrate BEOL-compatible ALD In2O3 transistors on the front-end-of-line (FEOL) devices with the maintenance of the satisfactory heat dissipation capability, a FEOL-interlayer-BEOL structure is proposed where the interlayer not only electrically isolates the FEOL and BEOL devices but also serves as a thermally conductive layer to alleviate the SHE.- 18 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70  (1) , 113-120
Alleviation of Self-Heating Effect in Top-Gated Ultrathin In2O3 FETs Using a Thermal Adhesion Layer
In this work, a thin layer of hexagonal boron nitride (h-BN) or HfO $_{\text{2}}$ serves as an adhesion layer between the ultrathin atomic-layer-deposited (ALD) indium oxide (In $_{\text{2}}$ O $_{\text{3}}$ ) channel and a sapphire substrate to enhance the thermal interfacial conductance. A thermo-reflectance (TR) measurement system with high spatial resolution is introduced to experimentally demonstrates the improvement. With the thin h-BN or HfO $_{\text{2}}$ interlayer, the temperature elevation ( $\Delta \textit{T}$ ) induced by self-heating effect (SHE) is decreased by roughly 9% or 27%, respectively. To quantify the improvement of the interfacial heat transfer, a steady-state thermal diffusion model with a finite-element method is combined with the experimental TR observation to extract the effective thermal boundary conductance (TBC) values in each case. It is shown that the effective TBC is ameliorated by a factor of 2 or 7 with the h-BN or HfO $_{\text{2}}$ interlayer, which is responsible for the $\Delta \textit{T}$ reduction. Furthermore, phonon density of states (PDOS) distribution mismatch implies that the intersection over union (IOU) ratio in the acoustic phonon region of In $_{\text{2}}$ O $_{\text{3}}$ with h-BN or HfO $_{\text{2}}$ is roughly 3 or 11 times higher than that directly with sapphire, which is responsible for the profound TBC enhancement. Based on this, ultrahigh maximum drain current of 2.4 mA/ $\mu $ m is achieved with 2.1-nm-thick In $_{\text{2}}$ O $_{\text{3}}$ channel on a sapphire substrate with an HfO $_{\text{2}}$ interlayer in between due to the alleviated SHE.
- 18 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70  (1) , 113-120
Alleviation of Self-Heating Effect in Top-Gated Ultrathin In2O3 FETs Using a Thermal Adhesion Layer
In this work, a thin layer of hexagonal boron nitride (h-BN) or HfO $_{\text{2}}$ serves as an adhesion layer between the ultrathin atomic-layer-deposited (ALD) indium oxide (In $_{\text{2}}$ O $_{\text{3}}$ ) channel and a sapphire substrate to enhance the thermal interfacial conductance. A thermo-reflectance (TR) measurement system with high spatial resolution is introduced to experimentally demonstrates the improvement. With the thin h-BN or HfO $_{\text{2}}$ interlayer, the temperature elevation ( $\Delta \textit{T}$ ) induced by self-heating effect (SHE) is decreased by roughly 9% or 27%, respectively. To quantify the improvement of the interfacial heat transfer, a steady-state thermal diffusion model with a finite-element method is combined with the experimental TR observation to extract the effective thermal boundary conductance (TBC) values in each case. It is shown that the effective TBC is ameliorated by a factor of 2 or 7 with the h-BN or HfO $_{\text{2}}$ interlayer, which is responsible for the $\Delta \textit{T}$ reduction. Furthermore, phonon density of states (PDOS) distribution mismatch implies that the intersection over union (IOU) ratio in the acoustic phonon region of In $_{\text{2}}$ O $_{\text{3}}$ with h-BN or HfO $_{\text{2}}$ is roughly 3 or 11 times higher than that directly with sapphire, which is responsible for the profound TBC enhancement. Based on this, ultrahigh maximum drain current of 2.4 mA/ $\mu $ m is achieved with 2.1-nm-thick In $_{\text{2}}$ O $_{\text{3}}$ channel on a sapphire substrate with an HfO $_{\text{2}}$ interlayer in between due to the alleviated SHE.
- 26 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43  (11) , 1905-1908
A Gate-All-Around inO Nanoribbon FET With Near 20 mA/m Drain Current
In this work, we demonstrate atomic-layer-deposited (ALD) single-channel indium oxide (In2O3) gate-all-around (GAA) nanoribbon field-effect transistors (FETs) in a back-end-of-line (BEOL) compatible process. A maximum on-state current (ION) of 19.3 mA/ $\mu \text{m}$ (near 20 mA/ $\mu \text{m}$ ) and an on/off ratio of 106 are achieved in an In2O3 GAA nanoribbon FET with a channel thickness (TIO) of 3.1 nm, channel length (Lch) of 40 nm, channel width (Wch) of 30 nm and dielectric HfO2 of 5 nm. Short-pulse measurements are applied to mitigate the self-heating effect induced by the ultra-high drain current flowing in the ultra-thin channel layer. The record high drain current obtained from an In2O3 FET is about one order of magnitude higher than any conventional single-channel semiconductor FETs. This extraordinary drain current and its related on-state performance demonstrate that ALD In2O3 is a promising oxide semiconductor channel with great opportunities in BEOL compatible monolithic 3D integration.
- 26 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43  (11) , 1905-1908
A Gate-All-Around inO Nanoribbon FET With Near 20 mA/m Drain Current
In this work, we demonstrate atomic-layer-deposited (ALD) single-channel indium oxide (In2O3) gate-all-around (GAA) nanoribbon field-effect transistors (FETs) in a back-end-of-line (BEOL) compatible process. A maximum on-state current (ION) of 19.3 mA/ $\mu \text{m}$ (near 20 mA/ $\mu \text{m}$ ) and an on/off ratio of 106 are achieved in an In2O3 GAA nanoribbon FET with a channel thickness (TIO) of 3.1 nm, channel length (Lch) of 40 nm, channel width (Wch) of 30 nm and dielectric HfO2 of 5 nm. Short-pulse measurements are applied to mitigate the self-heating effect induced by the ultra-high drain current flowing in the ultra-thin channel layer. The record high drain current obtained from an In2O3 FET is about one order of magnitude higher than any conventional single-channel semiconductor FETs. This extraordinary drain current and its related on-state performance demonstrate that ALD In2O3 is a promising oxide semiconductor channel with great opportunities in BEOL compatible monolithic 3D integration.
- 18 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
BEOL-Compatible, ALD-grown In2O3 Top-Gate FETs with Maximum Drain Current of 3 A/mm through Thermal Engineering and Pulse Measurement
This paper reports 1 A/mm drain current (I D ) and 0.24 Ω•mm contact resistance (R C ) at on-state with BEOL-compatible, top-gated, and ALD-grown 1.3-nm In 2 O 3 . Nonetheless, the devices suffer severely from self-heating effect (SHE) as larger bias is applied. Accordingly, beside quantitatively investigating the SHE in this system, thermal engineering is utilized to greatly alleviate it and therefore achieve higher I D of 2 A/mm by employing highly resistive silicon as the substrate. Moreover, pulse measurements further reduce SHE and attain even higher I D of 3 A/mm due to the lowered power rate of the devices.
- 18 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
BEOL-Compatible, ALD-grown In2O3 Top-Gate FETs with Maximum Drain Current of 3 A/mm through Thermal Engineering and Pulse Measurement
This paper reports 1 A/mm drain current (I D ) and 0.24 Ω•mm contact resistance (R C ) at on-state with BEOL-compatible, top-gated, and ALD-grown 1.3-nm In 2 O 3 . Nonetheless, the devices suffer severely from self-heating effect (SHE) as larger bias is applied. Accordingly, beside quantitatively investigating the SHE in this system, thermal engineering is utilized to greatly alleviate it and therefore achieve higher I D of 2 A/mm by employing highly resistive silicon as the substrate. Moreover, pulse measurements further reduce SHE and attain even higher I D of 3 A/mm due to the lowered power rate of the devices.
- 17 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69  (1) , 147-151
Realization of Maximum 2 A/mm Drain Current on Top-Gate Atomic-Layer-Thin Indium Oxide Transistors by Thermal Engineering
In this work, we demonstrate the record high maximum drain current ( ${I}_{{\mathrm {D}}}$ ) of 2 A/mm of top-gate (TG) indium oxide (In 2 O 3 ) transistors. The scaled and atomic-layer-deposited (ALD) In 2 O 3 transistors have channel length ( ${L}_{{\mathrm {ch}}}$ ) down to 40 nm and channel thickness ( ${T}_{{\mathrm {ch}}}$ ) down to 1.3 nm. Besides, the thermal budget of the whole material formation and device fabrication process is as low as 225 °C, making it compatible with back-end-of-line (BEOL) technologies by a huge margin. On the other hand, highly resistive silicon is utilized to serve as a desired high thermal conducting substrate to dissipate the generated heat efficiently as a larger current is conducted under a larger voltage bias. It greatly alleviates the self-heating effect (SHE) and allows an approximately 100% higher drain current. Quantitative studies of the SHE and channel temperature at ON-state with SiO 2 /Si and highly resistive silicon substrates are also presented.
- 17 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69  (1) , 147-151
Realization of Maximum 2 A/mm Drain Current on Top-Gate Atomic-Layer-Thin Indium Oxide Transistors by Thermal Engineering
In this work, we demonstrate the record high maximum drain current ( ${I}_{{\mathrm {D}}}$ ) of 2 A/mm of top-gate (TG) indium oxide (In 2 O 3 ) transistors. The scaled and atomic-layer-deposited (ALD) In 2 O 3 transistors have channel length ( ${L}_{{\mathrm {ch}}}$ ) down to 40 nm and channel thickness ( ${T}_{{\mathrm {ch}}}$ ) down to 1.3 nm. Besides, the thermal budget of the whole material formation and device fabrication process is as low as 225 °C, making it compatible with back-end-of-line (BEOL) technologies by a huge margin. On the other hand, highly resistive silicon is utilized to serve as a desired high thermal conducting substrate to dissipate the generated heat efficiently as a larger current is conducted under a larger voltage bias. It greatly alleviates the self-heating effect (SHE) and allows an approximately 100% higher drain current. Quantitative studies of the SHE and channel temperature at ON-state with SiO 2 /Si and highly resistive silicon substrates are also presented.
- 26 June 2020
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 13  (6) , 064063
Alignment of Polarization against an Electric Field in van der Waals Ferroelectrics
Polarization in ferroelectrics can be switched in the direction of an applied electric field by dipole reorientation, enabling numerous applications and fundamental phenomena. Here, we demonstrate that, in the van der Waals (vdW) layered ferrielectric , a unique mechanism exists where polarization aligns against the direction of the applied electric field, seemingly in violation of the fundamental properties of a dipolar solid. The mechanism is the result of the electric field driving the atoms unidirectionally across the vdW gaps, which is distinctively different from dipole reorientation. The crossing of atoms is the fundamental process of ionic conductivity, yet it is compatible with the existence of polarization. These phenomena are confirmed by nanoscale imaging and spectroscopy of ferroelectric capacitors, coupled with dynamic density-functional-theory simulations. The symbiotic relationship of ferroelectric and ionic phenomena enables alternative approaches to control polarization and necessitates a change in perspective on nucleation, domain-wall dynamics, and other ferroelectric and electromechanical characteristics in material systems where ionic and ferroelectric phenomena manifest.- 26 June 2020
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 13  (6) , 064063
Alignment of Polarization against an Electric Field in van der Waals Ferroelectrics
Polarization in ferroelectrics can be switched in the direction of an applied electric field by dipole reorientation, enabling numerous applications and fundamental phenomena. Here, we demonstrate that, in the van der Waals (vdW) layered ferrielectric , a unique mechanism exists where polarization aligns against the direction of the applied electric field, seemingly in violation of the fundamental properties of a dipolar solid. The mechanism is the result of the electric field driving the atoms unidirectionally across the vdW gaps, which is distinctively different from dipole reorientation. The crossing of atoms is the fundamental process of ionic conductivity, yet it is compatible with the existence of polarization. These phenomena are confirmed by nanoscale imaging and spectroscopy of ferroelectric capacitors, coupled with dynamic density-functional-theory simulations. The symbiotic relationship of ferroelectric and ionic phenomena enables alternative approaches to control polarization and necessitates a change in perspective on nucleation, domain-wall dynamics, and other ferroelectric and electromechanical characteristics in material systems where ionic and ferroelectric phenomena manifest.- 10 February 2020
- Published by Springer Nature in Nature Electronics
- Vol. 3  (3) , 141-147
Raman response and transport properties of tellurium atomic chains encapsulated in nanotubes
- 10 February 2020
- Published by Springer Nature in Nature Electronics
- Vol. 3  (3) , 141-147
Raman response and transport properties of tellurium atomic chains encapsulated in nanotubes