KAKarim Abbaszadeh

Karim Abbaszadeh

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Karim Abbaszadeh has a total of 69 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Multiport Buck-Boost Integrated On-Board EV Charger for Multi-Energy Powertrains

    by Homayoun Soltani Gohari, Amir Safaeinasab, Karim Abbaszadeh, Peter Sergeant, Hendrik Vansompel

    To enhance EV powertrains and align them with recent advancements—such as multi-source integration and the demand for higher power density—the development of an advanced charger power circuit is essential. Aiming at this, a multi-port integrated on-board EV charger designed for powertrains powered by various energy sources and operating in multiple modes is presented in this paper. By utilizing motor windings as the power factor correction (PFC) filter, the system reduces the overall weight, volume, and cost of the powertrain. The converter’s ability to operate in both buck and boost modes enables efficient energy management for each source. Additionally, integrating a vehicle-roof PV panel and a fuel cell (FC) reduces grid dependency and enhances charging flexibility. Furthermore, the vehicle-to-grid (V2G) capability allows energy to be fed back into the grid, improving overall energy utilization. The proposed charger is thoroughly analyzed, and the employed control strategy is discussed. Moreover, theoretical evaluations are carefully validated through experimental results of the implemented 500W prototype.

  • Open Access

    Fast Response Predictive Controllers for Mono-Inverter Dual Parallel Permanent Magnet Synchronous

    by Mehdi Fadaie, Karim Abbaszadeh, Alireza Siadatan

    The method of Mono-Inverter Dual-Parallel motors has been noticed in the drive of the multi-motor systems in order to reduce the number of power electronic devices as well as the volume, weight, and cost of the drive system. The load torque imbalance in motors has been one of the main problems of these systems because of feeding the motors by a single inverter. Some control methods have also been proposed in this field and studies are ongoing. This paper deals with an effective Model Predictive Control (MPC) method for the design of speed and current controllers in MIDP motors. Pontryagin’s Maximum Principle and the Lagrange method are used in designing the current and speed controllers respectively. The current controller generates control signals as linear-parametric functions through the offline solving of the quadratic-linear cost function. Instead of using conventional PI controllers in the speed control loop, speed controllers are designed based on the regulating kinetic energy of motors. After driving and simplifying the mathematical equations, the proposed method is simulated. Simulation results are compared with the Finite Control Set-MPC. These results validate the prompt and accurate performance of proposed controllers in transient and steady states.


  • A high-gain, low cost function thirteen level switched-capacitor single source multi-level inverter

    by Yaser Habibi, Jafar Siahbalaee, Mohammad Divandari, Karim Abbaszadeh


  • An Outer-Rotor L-Shaped Modular Consequent Pole Permanent Magnet Machine for In-Wheel Electric Bike Propulsion

    by Mohammadreza Naeimi, Karim Abbaszadeh, Johan Gyselinck

    Electric bikes (e-bikes) have become increasingly popular as a sustainable option of transportation in megacities, effectively tackling issues such as pollution and traffic congestion. However, a significant gap still exists between the manufacturing cost and the electrical motor performance in e-bikes. Thus, this article proposes a new outer rotor unequal pole L-shaped modular consequent pole (UPLM-CPM) machine with an N-I and I-S pole configuration as an in-wheel e-bike propulsion. The proposed machine incorporates a modular consequent-pole permanent magnet (CPM) rotor to provide a strong flux-focusing effect and a high PM utilization ratio. It also utilizes an L-shaped rotor with an unequal pole structure to improve electromagnetic characteristics, such as back electro-motive force (EMF) voltage, torque ripple, and cogging torque. Besides, both PM polarities are utilized in N-I and I-S sequences to suppress leakage flux. First, a parametric analysis is conducted on the L-shaped rotor parameters to explore the best combination. Then, the proposed machine, an L-shaped modular CPM (LM-CPM1) machine, the LM-CPM1 with both PM polarities (LM-CPM2), and a modular surface-mounted PM (M-SMPM) machine are compared by the finite element analysis (FEAs) in terms of torque characteristics, no-load characteristics, and leakage flux. Finally, the proposed e-bike propulsion is fabricated and tested to verify simulation results.


  • Open Access

    Design Consideration and Experimental Validation of a Common Grounded High Step-Up DC-DC Converter With High Voltage Gain in Both High and Low Duty Cycles

    by Seyed Hossein Aleyasin, Amir Safaeinasab, Mohsen Taghizadeh Kejani, Karim Abbaszadeh, Hadi Tarzamni

    In this paper, a new non-isolated high step-up DC-DC converter is proposed, which can achieve high voltage gains in both low and high duty cycles, so that different high voltage gains could be chosen from both low or high duty cycles. Therefore, by changing the duty cycle in proper time periods, the voltage stress on switches could be modified in a way that they can achieve a better life span, without having any noticeable change in the output voltage. The structure of the converter reduces the voltage stress on switches with small number of elements and the output voltage ripple is lower than 1% of the output voltage using a very small capacitor. The input current remains continuous, and the converter maintains a common ground between input and output terminals, making it ideal for battery storage systems and renewable energy applications such as photovoltaic (PV) panels. The paper thoroughly examines the operation in Continuous Conduction Mode (CCM), including an efficiency analysis, the derivation of the small-signal model, and closed-loop analysis. Additionally, the Discontinuous Conduction Mode (DCM) operation is explored in detail. The proposed converter is benchmarked against other boost converters, and a laboratory-scale prototype is constructed to validate the theoretical findings through experimental results.


  • Open Access

    A Novel External‐Rotor Consequent‐Pole Machine With Asymmetrical and Hybrid Pole Arrangement for E‐Bike Application

    by Mohammadreza Naeimi, Karim Abbaszadeh, Johan Gyselinck

    This article proposes a novel L‐shaped modular consequent‐pole permanent magnet (PM) machine with an asymmetrical and hybrid pole structure (namely the AHPLM‐CPM machine) designed for in‐hub electric bikes (e‐bikes). The AHPLM‐CPM machine combines L‐shaped modules with a consequent‐pole structure to enhance the PM utilisation ratio and flux‐focusing effect simultaneously. Additionally, a hybrid pole configuration, consisting of PM‐iron and iron‐PM sequences, is employed to reduce axial leakage flux. A multi‐objective optimisation is performed on the L‐shaped module parameters to minimise torque ripple while maximising average torque, leading to an asymmetrical pole structure. A comparative study on five proposed machines is conducted to highlight the superiority of the AHPLM‐CPM machine in terms of torque characteristics, back‐EMF voltage, airgap flux density and cost. Simulation results show that the PM utilisation ratio of the proposed machine is increased by 80.4% compared to a modular surface‐mounted PM (MSMPM) machine. Furthermore, the AHPLM‐CPM machine exhibits the lowest torque ripple and cogging torque while reducing PM costs by 50% compared to the MSMPM machine. Finally, a 250 r/min 500 W prototype is constructed and tested by considering the effect of the e‐bike's gear system to verify the simulation results.

  • Open Access

    A Single‐Switch Resonant High Voltage Gain DC‐DC Converter Based on Magnetic Coupling

    by Mohammad Reza Hosseiny, Karim Abbaszadeh

    This paper introduces a single switch high‐step‐up DC‐DC converter designed for photovoltaic energy system applications with the primary purpose of increasing the relatively low output voltage of photovoltaic panels to the DC‐bus voltage of 400 V. The proposed high step‐up converter is centered on a coupled inductor, thereby providing flexibility in the output voltage range, enabling the attainment of higher voltage gain. To recycle the leakage inductance energy, the resonance method is employed. Additionally, the clamped capacitor effectively minimizes voltage stress on the main switch by clamping the capacitor voltage on the switch, thereby alleviating large voltage spikes, resulting in the implementation of a low on‐resistance single switch, leading to simplified switch control, and ultimately enhanced efficiency. By incorporating the non‐isolating approach and hence having a common ground structure, the system's power density is enhanced, and electromagnetic interference (EMI) effects are reduced. A comprehensive and comparative analysis of the steady‐state operation and design of the proposed converter is presented, with detailed examination of its performance metrics and thorough comparison to various existing converter topologies. Experimental results have been obtained from a 25 V/402 V/200 W prototype, validating the correct operation and feasibility of the presented converter.


  • Open Access

    2‐D Electromagnetic Analysis Coupled With 3‐D Thermal Analysis of a Dual‐PM Excited Flux‐Switching Generator With Overhang Structure for Direct Drive Wind Turbines

    by Amir Ebrahimi Shohani, Mohammad Farahzadi, Salman Ali, Karim Abbaszadeh, Fabrizio Marignetti, Fariba Farrokh

    This study introduces a new outer‐rotor dual‐permanent magnet (PM) excited flux‐switching generator with an overhang structure for direct‐drive wind turbine applications. The proposed generator incorporates flux barriers and ferrite PMs in the stator while utilising neodymium PMs in the rotor segments. Contrary to ferrite PMs, neodymium PMs are prone to demagnetisation in high‐temperature conditions. Given that the operating temperature of the stator is nearly double that of the rotor in this study, ferrite PMs are strategically positioned in the stator to mitigate this issue. The main goal of this paper is to provide a fast and accurate method to study the electromagnetic‐thermal performance of the generator. Hence, a two‐dimensional finite element analysis (2‐D FEA) electromagnetic analysis is coupled with a 3‐D FEA thermal analysis. Moreover, a precise thermal circuit of each generator's element is displayed. Finally, the accuracy of the method is confirmed through a comparison of the simulation results with experimental data, indicating a small margin of error.


  • Open Access

    Design and Experimental Validation of a New Outer Rotor Double PM Excited Flux Switching Generator for Direct Drive Wind Turbines

    by Mohammad Farahzadi, Salman Ali, Seyedarmin Mirnikjoo, Karim Abbaszadeh, Fabrizio Marignetti, Maryam Salehi

    An outer rotor double permanent magnet (PM) excited flux switching generator is designed and optimized in this paper for direct drive wind turbine applications. This generator consists of two sets of PMs: ferrite PMs embedded in the stator yoke and neodymium PMs sandwiched between the rotor segments. In this regard, the main justification for employing ferrite PMs in the stator yoke is that the risk of demagnetization of ferrite PMs at high temperatures is lower than that of neodymium PMs (the temperature of the machine’s stationary parts is higher than that of its rotating parts). For the design of the machine, the Taguchi design of experiments is deployed, while a decision-making algorithm based on the technique for order of preference by similarity to the ideal solution is used to solve the contradiction that results from the Taguchi design of experiments in the multi-objective design optimization process. During the multi-objective design optimization steps, simultaneously maximizing the no-load phase voltage and minimizing the cogging torque and total harmonic distortion of the no-load phase voltage are defined as the objective functions. The optimally designed machine is prototyped and subsequently subjected to experimental validation to verify the predictions in satisfying the objective functions.