Zhiliang Xia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zhiliang Xia has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Zongliang Huo
Institute of Microelectronics, Chinese Academy of Sciences, Beijing, China
9 shared publications - Tao Yang
Institute of Microelectronics of the Chinese Academy of Sciences, Beijing, China
5 shared publications Wenxi Zhou
Yangtze Memory Technologies Co Ltd, No. 88, Future 3rd Road, Donghu New Technology Development Zone, Wuhan, Hubei, 430000, CHINA
5 shared publicationsLei Liu
Yangtze Memory Technologies Co Ltd, No. 88, Future 3rd Road, Donghu New Technology Development Zone, Wuhan, Hubei, 430000, CHINA
4 shared publications- Tao Yang
Institute of Microelectronics of the Chinese Academy of Sciences, Beijing 100029, China
3 shared publications Yuancheng Yang
Yangtze Memory Technologies Co Ltd, No. 88, Future 3rd Road, Donghu New Technology Development Zone, Wuhan, Hubei, 430000, CHINA
3 shared publications
Latest Publications
- Open Access
- 20 March 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (3) , 686
Self-Adaption of the GIDL Erase Promotes Stacking More Layers in 3D NAND Flash
The bit density is generally increased by stacking more layers in 3D NAND Flash. Gate-induced drain leakage (GIDL) erase is a critical enabler in the future development of 3D NAND Flash. The relationship between the drain-to-body potential (Vdb) of GIDL transistors and the increasing number of layers was studied to explain the reason for the self-adaption of the GIDL erase. The dynamics controlled by the drain-to-body and drain-to-gate potential contribute to the self-adaption of the GIDL erase. Increasing the number of layers leads to a longer duration of the maximum value of Vdb (Vdb_max), combined with the increased drain-to-gate potential, which enhances the GIDL current and further boosts channel potential to reach the same value at different positions of the NAND string. We proposed a method based on the correlation between the duration of Vdb_max and the number of layers to obtain the limited layers of the GIDL erase. The limited layers allowed are more than four times the number of layers used in the current simulation. Combining the novel method of dividing the channel into multi-regions with the asynchronous GIDL erase method will be useful for further stacking more layers in 3D NAND Flash.
- 20 March 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (3) , 686
Open AccessSelf-Adaption of the GIDL Erase Promotes Stacking More Layers in 3D NAND Flash
The bit density is generally increased by stacking more layers in 3D NAND Flash. Gate-induced drain leakage (GIDL) erase is a critical enabler in the future development of 3D NAND Flash. The relationship between the drain-to-body potential (Vdb) of GIDL transistors and the increasing number of layers was studied to explain the reason for the self-adaption of the GIDL erase. The dynamics controlled by the drain-to-body and drain-to-gate potential contribute to the self-adaption of the GIDL erase. Increasing the number of layers leads to a longer duration of the maximum value of Vdb (Vdb_max), combined with the increased drain-to-gate potential, which enhances the GIDL current and further boosts channel potential to reach the same value at different positions of the NAND string. We proposed a method based on the correlation between the duration of Vdb_max and the number of layers to obtain the limited layers of the GIDL erase. The limited layers allowed are more than four times the number of layers used in the current simulation. Combining the novel method of dividing the channel into multi-regions with the asynchronous GIDL erase method will be useful for further stacking more layers in 3D NAND Flash.
- 18 January 2023
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 38 (2) , 025013
An effective solution to optimize the saddle-shape warpage in 3D IC applications by patterning laser treatment
The asymmetric saddle-shape warpage is one of the hardest limitations on the development of three-dimensional integrated circuits (3D ICs) as the vertical integration increases. To improve the product yield, an effective method for saddle-shape warpage reduction in 3D IC production by backside patterning laser annealing treatment with a multilayer structure is investigated in this work. The reduction of saddle-shaped warpage by patterning laser treatment is the first time in 3D NAND array wafer application and through simulations and experiments, the laser annealing pattern is determined. In addition, the materials of the multilayer structure are selected as amorphous Al2O3 and TiN according to experiments and theoretical analysis. As a result, a conformal 47.8 µm optimization of the saddle-shape warpage is successfully reached in a control wafer test by patterning laser annealing treatment.
- 18 January 2023
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 38 (2) , 025013
An effective solution to optimize the saddle-shape warpage in 3D IC applications by patterning laser treatment
The asymmetric saddle-shape warpage is one of the hardest limitations on the development of three-dimensional integrated circuits (3D ICs) as the vertical integration increases. To improve the product yield, an effective method for saddle-shape warpage reduction in 3D IC production by backside patterning laser annealing treatment with a multilayer structure is investigated in this work. The reduction of saddle-shaped warpage by patterning laser treatment is the first time in 3D NAND array wafer application and through simulations and experiments, the laser annealing pattern is determined. In addition, the materials of the multilayer structure are selected as amorphous Al2O3 and TiN according to experiments and theoretical analysis. As a result, a conformal 47.8 µm optimization of the saddle-shape warpage is successfully reached in a control wafer test by patterning laser annealing treatment.
- Open Access
- 16 January 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (1) , 230
Activation Enhancement and Grain Size Improvement for Poly-Si Channel Vertical Transistor by Laser Thermal Annealing in 3D NAND Flash
The bit density is generally increased by stacking more layers in 3D NAND Flash. Lowering dopant activation of select transistors results from complex integrated processes. To improve channel dopant activation, the test structure of vertical channel transistors was used to investigate the influence of laser thermal annealing on dopant activation. The activation of channel doping by different thermal annealing methods was compared. The laser thermal annealing enhanced the channel activation rate by at least 23% more than limited temperature rapid thermal annealing. We then comprehensively explore the laser thermal annealing energy density on the influence of Poly-Si grain size and device performance. A clear correlation between grain size mean and grain size sigma, large grain size mean and sigma with large laser thermal annealing energy density. Large laser thermal annealing energy density leads to tightening threshold voltage and subthreshold swing distribution since Poly-Si grain size regrows for better grain size distribution with local grains optimization. As an enabler for next-generation technologies, laser thermal annealing will be highly applied in 3D NAND Flash for better device performance with stacking more layers, and opening new opportunities of novel 3D architectures in the semiconductor industry.
- 16 January 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (1) , 230
Open AccessActivation Enhancement and Grain Size Improvement for Poly-Si Channel Vertical Transistor by Laser Thermal Annealing in 3D NAND Flash
The bit density is generally increased by stacking more layers in 3D NAND Flash. Lowering dopant activation of select transistors results from complex integrated processes. To improve channel dopant activation, the test structure of vertical channel transistors was used to investigate the influence of laser thermal annealing on dopant activation. The activation of channel doping by different thermal annealing methods was compared. The laser thermal annealing enhanced the channel activation rate by at least 23% more than limited temperature rapid thermal annealing. We then comprehensively explore the laser thermal annealing energy density on the influence of Poly-Si grain size and device performance. A clear correlation between grain size mean and grain size sigma, large grain size mean and sigma with large laser thermal annealing energy density. Large laser thermal annealing energy density leads to tightening threshold voltage and subthreshold swing distribution since Poly-Si grain size regrows for better grain size distribution with local grains optimization. As an enabler for next-generation technologies, laser thermal annealing will be highly applied in 3D NAND Flash for better device performance with stacking more layers, and opening new opportunities of novel 3D architectures in the semiconductor industry.
- 15 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 36 (1) , 139-143
An Emerging Local Annealing Method for Simultaneous Crystallization and Activation in Xtacking 3-D NAND Flash
The high thermal budget of three-dimensional NAND Flash (3D NAND Flash) is the key issue limiting the increase in vertical integration. The main purpose of this article is to design a local and high temperature annealing function to reduce the thermal budget and gain a high activation rate without diffusion at a target depth to improve the performance of 3D NAND Flash devices by laser annealing with green wavelength. The method of nanosecond pulse laser annealing (ns-PLA) for amorphous silicon (a-Si) crystallization and activation has been proven, and this method has the benefits of a low thermal budget and controllable heating. According to previous experiments, one of the important results is that ns-PLA with high energy can provide a high temperature that reaches the melting point of a-Si and obtain a deep and monocrystal-like silicon channel through liquid phase crystallization in 3D NAND applications and obtain a higher activation rate. These results cast emerging light on low thermal budget processes based on ns-PLA in 3D NAND flash for future architecture such as Xtacking architecture, and have significant ramifications for impurity activation rates and reducing channel leakages.
- 15 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 36 (1) , 139-143
An Emerging Local Annealing Method for Simultaneous Crystallization and Activation in Xtacking 3-D NAND Flash
The high thermal budget of three-dimensional NAND Flash (3D NAND Flash) is the key issue limiting the increase in vertical integration. The main purpose of this article is to design a local and high temperature annealing function to reduce the thermal budget and gain a high activation rate without diffusion at a target depth to improve the performance of 3D NAND Flash devices by laser annealing with green wavelength. The method of nanosecond pulse laser annealing (ns-PLA) for amorphous silicon (a-Si) crystallization and activation has been proven, and this method has the benefits of a low thermal budget and controllable heating. According to previous experiments, one of the important results is that ns-PLA with high energy can provide a high temperature that reaches the melting point of a-Si and obtain a deep and monocrystal-like silicon channel through liquid phase crystallization in 3D NAND applications and obtain a higher activation rate. These results cast emerging light on low thermal budget processes based on ns-PLA in 3D NAND flash for future architecture such as Xtacking architecture, and have significant ramifications for impurity activation rates and reducing channel leakages.
- Open Access
- 19 October 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (10) , 1772
A Novel Capacitorless 1T DRAM with Embedded Oxide Layer
A novel vertical dual surrounding gate transistor with embedded oxide layer is proposed for capacitorless single transistor DRAM (1T DRAM). The embedded oxide layer is innovatively used to improve the retention time by reducing the recombination rate of stored holes and sensing electrons. Based on TCAD simulations, the new structure is predicted to not only have the characteristics of fast access, random read and integration of 4F2 cell, but also to realize good retention and deep scaling. At the same time, the new structure has the potential of scaling compared with the conventional capacitorless 1T DRAM.
- 19 October 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (10) , 1772
Open AccessA Novel Capacitorless 1T DRAM with Embedded Oxide Layer
A novel vertical dual surrounding gate transistor with embedded oxide layer is proposed for capacitorless single transistor DRAM (1T DRAM). The embedded oxide layer is innovatively used to improve the retention time by reducing the recombination rate of stored holes and sensing electrons. Based on TCAD simulations, the new structure is predicted to not only have the characteristics of fast access, random read and integration of 4F2 cell, but also to realize good retention and deep scaling. At the same time, the new structure has the potential of scaling compared with the conventional capacitorless 1T DRAM.
- Open Access
- 28 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 1243-1247
Optimization of Bump Defect at High-Concentration In-Situ Phosphorus Doped Polysilicon/TEOS Oxide Interface for 3D NAND Flash Memory Application
In the 3D NAND Flash memory manufacturing process, high-concentration in-situ phosphorus-doped polysilicon and TEOS oxide stack will produce bump defects at the interfaces, causing pattern defects and electrical failures. The formation mechanism of bump defects caused by oxygen-containing groups and phosphorus at the lower and upper interfaces of phosphorus-doped polysilicon is investigated in detail. Two methods were demonstrated to reduce bump defects, wet processing and Rapid Thermal Oxidation (RTO). The wet processing is to remove oxygen-containing groups and phosphorus, while the RTO process increases the solubility of phosphorus in silicon. Both methods have significantly reduced bump defects and greatly increased the yield rate, and further verify the proposed formation mechanism of bump defects.
- 28 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 1243-1247
Open AccessOptimization of Bump Defect at High-Concentration In-Situ Phosphorus Doped Polysilicon/TEOS Oxide Interface for 3D NAND Flash Memory Application
In the 3D NAND Flash memory manufacturing process, high-concentration in-situ phosphorus-doped polysilicon and TEOS oxide stack will produce bump defects at the interfaces, causing pattern defects and electrical failures. The formation mechanism of bump defects caused by oxygen-containing groups and phosphorus at the lower and upper interfaces of phosphorus-doped polysilicon is investigated in detail. Two methods were demonstrated to reduce bump defects, wet processing and Rapid Thermal Oxidation (RTO). The wet processing is to remove oxygen-containing groups and phosphorus, while the RTO process increases the solubility of phosphorus in silicon. Both methods have significantly reduced bump defects and greatly increased the yield rate, and further verify the proposed formation mechanism of bump defects.
- Open Access
- 15 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 8, 1021-1024
Hydrogen Source and Diffusion Path for Poly-Si Channel Passivation in Xtacking 3D NAND Flash Memory
Poly-Si channels need well passivated by using hydrogen passivation process in 3D NAND flash memories for better poly-Si quality with low trap density. It is believed that Xtacking 3D NAND flash memory has the advantage of flexible arranging the passivation process. In this paper, two different passivation locations were compared in Xtacking structure to achieve better trap passivation. An optimized passivation process conducted at wafer backside with passivation SiN as hydrogen diffusion source was found to have an improved trap passivation result. This benefit was attributed to the sufficient H diffusion paths in Xtacking. These results also indicated the advantage of trap passivation for future higher stacked Xtacking 3D NAND flash memory.
- 15 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 8, 1021-1024
Open AccessHydrogen Source and Diffusion Path for Poly-Si Channel Passivation in Xtacking 3D NAND Flash Memory
Poly-Si channels need well passivated by using hydrogen passivation process in 3D NAND flash memories for better poly-Si quality with low trap density. It is believed that Xtacking 3D NAND flash memory has the advantage of flexible arranging the passivation process. In this paper, two different passivation locations were compared in Xtacking structure to achieve better trap passivation. An optimized passivation process conducted at wafer backside with passivation SiN as hydrogen diffusion source was found to have an improved trap passivation result. This benefit was attributed to the sufficient H diffusion paths in Xtacking. These results also indicated the advantage of trap passivation for future higher stacked Xtacking 3D NAND flash memory.
- 10 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 41 (6) , 840-843
Optimization of Performance and Reliability in 3D NAND Flash Memory
3D NAND Flash with high storage capacity is in great demand for several technologies, which requires high performance and good reliability at the same time. Therefore, it is proposed to adjust the tunnel layer by changing the first SiO 2 (O1) layer thickness near poly Si channel in the tunnel layer based on SiO 2 /SiO x N y /SiO 2 structure. The optimal thickness of O1 layer is found. Under the optimal condition, program speed increased by 19% compared with no O1 layer deposition, though erase speed is slightly decreased by about 7%, the initial threshold voltage shift is improved greatly. Experimental results demonstrate that there are complex mechanisms affected by the dielectric constant, band barrier and equivalent oxide thickness. The optimization of O1 layer is useful towards an understanding of program/erase speed and retention characteristics.
- 10 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 41 (6) , 840-843
Optimization of Performance and Reliability in 3D NAND Flash Memory
3D NAND Flash with high storage capacity is in great demand for several technologies, which requires high performance and good reliability at the same time. Therefore, it is proposed to adjust the tunnel layer by changing the first SiO 2 (O1) layer thickness near poly Si channel in the tunnel layer based on SiO 2 /SiO x N y /SiO 2 structure. The optimal thickness of O1 layer is found. Under the optimal condition, program speed increased by 19% compared with no O1 layer deposition, though erase speed is slightly decreased by about 7%, the initial threshold voltage shift is improved greatly. Experimental results demonstrate that there are complex mechanisms affected by the dielectric constant, band barrier and equivalent oxide thickness. The optimization of O1 layer is useful towards an understanding of program/erase speed and retention characteristics.
- Open Access
- 30 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 8 (1) , 140-144
Analysis and Optimization of Threshold Voltage Variability by Polysilicon Grain Size Simulation in 3D NAND Flash Memory
The impact of linear correlation between lognormal distribution grain size mean and sigma along the polysilicon channel on threshold voltage (Vth) variability has been investigated in three dimensional (3D) NAND flash. The variety of grain size mean and sigma results in the unstable Vth variability. To obtain a stable Vth distribution with various grain size mean, the grain size mean dependent Vth variability sensitivity to the grain size sigma was used to optimize the linear correlation between grain size mean and sigma via TCAD simulation. The optimized linear correlation with stable Vth variability is obtained except for the “unbalance region” affected by the combination of grain boundaries and positions with these grain size mean and sigma values resulting in the slightly shrinking Vth variability. Our results strongly suggest that this approach could guide the direction of polysilicon crystallization optimization to obtain stable Vth distribution with the predicted linear correlation between grain size mean and sigma.
- 30 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 8 (1) , 140-144
Open AccessAnalysis and Optimization of Threshold Voltage Variability by Polysilicon Grain Size Simulation in 3D NAND Flash Memory
The impact of linear correlation between lognormal distribution grain size mean and sigma along the polysilicon channel on threshold voltage (Vth) variability has been investigated in three dimensional (3D) NAND flash. The variety of grain size mean and sigma results in the unstable Vth variability. To obtain a stable Vth distribution with various grain size mean, the grain size mean dependent Vth variability sensitivity to the grain size sigma was used to optimize the linear correlation between grain size mean and sigma via TCAD simulation. The optimized linear correlation with stable Vth variability is obtained except for the “unbalance region” affected by the combination of grain boundaries and positions with these grain size mean and sigma values resulting in the slightly shrinking Vth variability. Our results strongly suggest that this approach could guide the direction of polysilicon crystallization optimization to obtain stable Vth distribution with the predicted linear correlation between grain size mean and sigma.
- Open Access
- 1 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 140054-140061
An Improved Dimensional Measurement Method of Staircase Patterns With Higher Precision in 3D NAND
3D NAND is a great architectural innovation in the field of flash memory. The staircase for control gate is a unique and important process in the manufacturing of 3D NAND. The staircase is employed to form the electrical connection between the control gate and contact. The current method used to measure the dimension of staircase patterns is, however, not precise enough for the development of state-of-the-art 3D NAND. In this circumstance, an accurate measurement of dimension for as-formed staircase patterns is of great importance and technical interest. In this paper, an improved measurement method is proposed to meet the requirement for higher precision. By taking the overlay into account, a calculation formula for measuring the dimensional error of as-formed staircase is derived for the first time. Two kinds of anchor design (convex SS0 and concave SS0) are put forward to perform dedicated experiments. Achieved results show that the measurement error of as-formed staircase using this improved method is improved from 31.6 nm for normal measurement method to 14.1 nm. The dimensional uniformity of as-formed staircase is therefore improved significantly which in turn leads to well controlled word line leakage. Furthermore, in advanced staircase structure of stair divided scheme (SDS), the convex SS0 shows an advantage in cost compared to the concave SS0.
- 1 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 140054-140061
Open AccessAn Improved Dimensional Measurement Method of Staircase Patterns With Higher Precision in 3D NAND
3D NAND is a great architectural innovation in the field of flash memory. The staircase for control gate is a unique and important process in the manufacturing of 3D NAND. The staircase is employed to form the electrical connection between the control gate and contact. The current method used to measure the dimension of staircase patterns is, however, not precise enough for the development of state-of-the-art 3D NAND. In this circumstance, an accurate measurement of dimension for as-formed staircase patterns is of great importance and technical interest. In this paper, an improved measurement method is proposed to meet the requirement for higher precision. By taking the overlay into account, a calculation formula for measuring the dimensional error of as-formed staircase is derived for the first time. Two kinds of anchor design (convex SS0 and concave SS0) are put forward to perform dedicated experiments. Achieved results show that the measurement error of as-formed staircase using this improved method is improved from 31.6 nm for normal measurement method to 14.1 nm. The dimensional uniformity of as-formed staircase is therefore improved significantly which in turn leads to well controlled word line leakage. Furthermore, in advanced staircase structure of stair divided scheme (SDS), the convex SS0 shows an advantage in cost compared to the concave SS0.