Rayane Dantas da Cunha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rayane Dantas da Cunha has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Evans Paiva da Costa Ferreira
Department of Mechanical Engineering, University Campus, Federal University of Rio Grande do Norte, Natal-RN, Brazil
3 shared publicationsJosé Daniel Diniz Melo
Department of Mechanical Engineering, University Campus, Federal University of Rio Grande do Norte, Natal-RN, Brazil
3 shared publications- Raimundo Carlos Silverio Freire Júnior
Federal University of Rio Grande do Norte
3 shared publications Cristiano Cardoso
SENAI Institute of Innovation in Advanced Manufacturing and Microfabrication, Santo Amaro, Brazil
2 shared publications- Talita Galvão Targino
Department of Mechanical Engineering, University Campus, Federal University of Rio Grande do Norte, Natal-RN, Brazil
2 shared publications Antonio M Medeiros
SENAI Institute of Innovation in Renewable Energy, Natal-RN, Brazil
1 shared publication
Latest Publications
- 14 June 2025
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (29) , 3305-3319
Erosion behavior of turbine blades due to sand and salt particles
This study investigates the degradation of wind turbine blades (WTBs) exposed to the atmospheric conditions of tropical coastal environments. A wind tunnel experimental methodology was employed to simulate the erosive effects of airborne particulates, focusing on the influence of salt and sand particles. Specimens were subjected to controlled wind speeds and impact angles to assess material wear mechanisms. The results indicated that a 45° impact angle led to increased material loss due to both normal and tangential impact components. The highest mass loss recorded was 0.78% in the salt and sand particles test, while the most significant increase in surface roughness was 1.89 µm at a 90° impact angle, confirming the severe impact of perpendicular erosion. SEM analysis revealed that fiberglass delamination contributed to the degradation process, particularly in high-impact scenarios. These findings provide insights into material behavior under extreme coastal conditions and emphasize the need for improved protective coatings and maintenance strategies for WTBs in tropical maritime regions.
- 14 June 2025
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (29) , 3305-3319
Erosion behavior of turbine blades due to sand and salt particles
This study investigates the degradation of wind turbine blades (WTBs) exposed to the atmospheric conditions of tropical coastal environments. A wind tunnel experimental methodology was employed to simulate the erosive effects of airborne particulates, focusing on the influence of salt and sand particles. Specimens were subjected to controlled wind speeds and impact angles to assess material wear mechanisms. The results indicated that a 45° impact angle led to increased material loss due to both normal and tangential impact components. The highest mass loss recorded was 0.78% in the salt and sand particles test, while the most significant increase in surface roughness was 1.89 µm at a 90° impact angle, confirming the severe impact of perpendicular erosion. SEM analysis revealed that fiberglass delamination contributed to the degradation process, particularly in high-impact scenarios. These findings provide insights into material behavior under extreme coastal conditions and emphasize the need for improved protective coatings and maintenance strategies for WTBs in tropical maritime regions.
- 8 August 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (23) , 2555-2564
Damage resistance and damage tolerance of a double-double fiber-reinforced polymer composite laminate to impact
This article analyzes the damage tolerance after impact of an unconventional carbon/epoxy laminate (AS4/8552) of the Double-Double (DD) type tested with different impact energies and compares it to a traditional laminate with equivalent properties. Quadriaxial (QUAD) laminate has stacking sequence [03/90/±45]S and the DD equivalent laminate has stacking sequence [0/-55/0/+55]3T. These materials were subjected to the low velocity impact test (LVI) with three energy levels (30 J, 45 J and 74 J), the uniaxial compression test and the compression after impact (CAI). The objective of this article is to validate whether the proposed DD laminate can be a replacement for the QUAD presented, considering the behavior under impact. In addition to the comparative study, this article also has the objective of evaluating whether it is possible to relate the damage tolerance with the delaminated area, and for this purpose, X-ray computed tomography (CT) was performed, making it possible to measure and locate the damage found in the samples.
- 8 August 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (23) , 2555-2564
Damage resistance and damage tolerance of a double-double fiber-reinforced polymer composite laminate to impact
This article analyzes the damage tolerance after impact of an unconventional carbon/epoxy laminate (AS4/8552) of the Double-Double (DD) type tested with different impact energies and compares it to a traditional laminate with equivalent properties. Quadriaxial (QUAD) laminate has stacking sequence [03/90/±45]S and the DD equivalent laminate has stacking sequence [0/-55/0/+55]3T. These materials were subjected to the low velocity impact test (LVI) with three energy levels (30 J, 45 J and 74 J), the uniaxial compression test and the compression after impact (CAI). The objective of this article is to validate whether the proposed DD laminate can be a replacement for the QUAD presented, considering the behavior under impact. In addition to the comparative study, this article also has the objective of evaluating whether it is possible to relate the damage tolerance with the delaminated area, and for this purpose, X-ray computed tomography (CT) was performed, making it possible to measure and locate the damage found in the samples.
- 5 June 2023
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 57 (19) , 2985-2993
Damage tolerance related to the damage area of impacted carbon/epoxy composite laminates
This study aimed to analyze the damage tolerance of a carbon/epoxy composite laminate (AS4/8552) impacted at low velocity, relating residual strength values with the impact energy and delaminated area. AS4/8552 laminated plates [0°3/90°/±45°]S were submitted to low-velocity impact tests with three energy levels: 30 J, 45 J and 74 J. Next, the test specimens were analyzed by X-ray computed tomography to check for cracks and delaminations, and compression after impact (CAI) tests conducted to assess their residual strength. The results indicate that above the minimum energy level of low-velocity impact to cause damage, the residual strength of the laminate may be related to the delaminated area.
- 5 June 2023
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 57 (19) , 2985-2993
Damage tolerance related to the damage area of impacted carbon/epoxy composite laminates
This study aimed to analyze the damage tolerance of a carbon/epoxy composite laminate (AS4/8552) impacted at low velocity, relating residual strength values with the impact energy and delaminated area. AS4/8552 laminated plates [0°3/90°/±45°]S were submitted to low-velocity impact tests with three energy levels: 30 J, 45 J and 74 J. Next, the test specimens were analyzed by X-ray computed tomography to check for cracks and delaminations, and compression after impact (CAI) tests conducted to assess their residual strength. The results indicate that above the minimum energy level of low-velocity impact to cause damage, the residual strength of the laminate may be related to the delaminated area.
- 13 March 2023
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 57 (10) , 1807-1817
Low velocity impact response of non-traditional double-double laminates
A novel family of composite laminates with a simplified stacking sequence and double-double layup [±ϕ/±ψ] n has significant potential to reduce weight and increase strength, while facilitating design optimization and simplifying the manufacturing process. In this study, the low-velocity impact response of a double-double (DD) laminate and a quadriaxial (Quad) laminate of equivalent stiffness and thickness were compared. Carbon/epoxy laminates were produced with stacking sequences of [±0/±50]10 and [03/90/±45/02/±45]2S corresponding to double-double and quadriaxial varieties, respectively. Low velocity impact tests were conducted at 74 J of energy and damage areas were examined using X-ray computed tomography. Compressive strength and compression after impact (CAI) strength were equivalent for the two laminates. However, differences in impact damage morphology were observed and are discussed.
- 13 March 2023
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 57 (10) , 1807-1817
Low velocity impact response of non-traditional double-double laminates
A novel family of composite laminates with a simplified stacking sequence and double-double layup [±ϕ/±ψ] n has significant potential to reduce weight and increase strength, while facilitating design optimization and simplifying the manufacturing process. In this study, the low-velocity impact response of a double-double (DD) laminate and a quadriaxial (Quad) laminate of equivalent stiffness and thickness were compared. Carbon/epoxy laminates were produced with stacking sequences of [±0/±50]10 and [03/90/±45/02/±45]2S corresponding to double-double and quadriaxial varieties, respectively. Low velocity impact tests were conducted at 74 J of energy and damage areas were examined using X-ray computed tomography. Compressive strength and compression after impact (CAI) strength were equivalent for the two laminates. However, differences in impact damage morphology were observed and are discussed.
- 23 February 2020
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 54 (21) , 3009-3019
The variation in low speed impact strength on glass fiber/Kevlar composite hybrids
The aim of this study was to analyze the effect of hybridization on impact and residual strength in composites as well as the types of damage caused by the impacts, quantifying the delaminated area of the test specimens. Two 11-layer composite laminates were developed, one with bidirectional glass fiber woven and the other a hybrid with three layers of bidirectional aramid fiber substituting the outer layers and the middle layer of the glass fiber. The materials revealed that the hybrid laminate obtained greater impact strength withstanding one impact of 76 J, albeit with an increase in the damaged area of between 64 and 85 cm2, resulting in a decline in mechanical properties along nearly the entire test specimen. This contrasts with what occurred in the glass fiber laminates, which recovered over 80% of their mechanical properties for a distance of 35 mm from the edge of the impactor. Moreover, it demonstrated that the variation in residual strength can be represented by an equation and that there is a relation between the damage area and the residual properties of the glass fiber material.
- 23 February 2020
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 54 (21) , 3009-3019
The variation in low speed impact strength on glass fiber/Kevlar composite hybrids
The aim of this study was to analyze the effect of hybridization on impact and residual strength in composites as well as the types of damage caused by the impacts, quantifying the delaminated area of the test specimens. Two 11-layer composite laminates were developed, one with bidirectional glass fiber woven and the other a hybrid with three layers of bidirectional aramid fiber substituting the outer layers and the middle layer of the glass fiber. The materials revealed that the hybrid laminate obtained greater impact strength withstanding one impact of 76 J, albeit with an increase in the damaged area of between 64 and 85 cm2, resulting in a decline in mechanical properties along nearly the entire test specimen. This contrasts with what occurred in the glass fiber laminates, which recovered over 80% of their mechanical properties for a distance of 35 mm from the edge of the impactor. Moreover, it demonstrated that the variation in residual strength can be represented by an equation and that there is a relation between the damage area and the residual properties of the glass fiber material.