ANAlisa V. Nikonenko

Alisa V. Nikonenko

*This is an algorithmically generated author record based on publicly available information.

Alisa V. Nikonenko has a total of 62 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    РАСПРЕДЕЛЕНИЕ ХИМИЧЕСКИХ ЭЛЕМЕНТОВ В МОДИФИЦИРОВАННОМ СЛОЕ УМЗ-СПЛАВА ВТ1-0 ПОД ДЕЙСТВИЕМ ИМПЛАНТАЦИИ ИОНАМИ АЛЮМИНИЯ

    by Елена Никоненко, Наталья Попова, Алиса Никоненко

    Проведено исследование градиентной структуры, возникающей при имплантации ионами алюминия сплава ВТ1-0 (технически чистого титана) в ультрамелкозернистом состоянии. Для формирова-ния ультрамелкозернистогосостояния был применен комбинированный метод многократного одноосного прессования (аbc-прессование) с последующей многоходовой прокаткой в ручьевых валках при комнатной температуре и последующим отжигом 673К, 1 час. Ионная имплантация проводилась при дозах облучения: 11017, 51017 и 101017ион/см2. Исследование выполнено методом просвечивающей электронной дифрак-ционной микроскопии и энергодисперсионной рентгеновской спектроскопии на фольгах, вырезанных пер-пендикулярно обработанной поверхности образца. Установлено, что сформированная имплантацией гради-ентная структура, состоит из 5 слоев: 1 –оксидный слой; 2 –ионно-имплантированный слой; 3 –слой с раз-рушенной зеренной структурой; 4 –слой остаточного влияния имплантации; 5 –слой, соответствующий не имплантированному состоянию сплава. В каждомслое определен фазовый состав, форма и расположение частиц вторых фаз, измерены размеры зерен -Ti, размеры, плотность распределения и объемные доли вы-делившихся частиц, проанализировано состояние твердого раствора. При каждой дозе облучения исследовано распределение алюминия по глубине модифицированных слоев. Установлено, что в слое 2 независимо от дозы облучения алюминий преимущественно участвует в образовании твердого раствора, оставшийся алюминий –в образовании интерметаллидных фаз. В слое 3 весь внедренный алюминий находится в интерметаллидных фазах. По мере удаления от обработанной поверхности образца содержание алюминия уменьшается, что приводит к уменьшению объемных долей интерметаллидных фаз. A study of the gradient structure arising from aluminum ion implantation of VT1-0 alloy (technically pure titanium) in the ultrafine-grained state has been carried out. To form the ultrafine-grained state, a combined method of multiple uniaxial pressing (abc-pressing) followed by multi-pass rolling in stream rolls at room tempera-ture and subsequent annealing at 673 K, 1 h was applied. Ion implantation was carried out at irradiation doses: 11017, 51017and 101017 ion/cm2. The study was carried out by transmission electron diffraction microscopy and energy-dispersive X-ray spectroscopy on foils cut perpendicular to the treated surface of the sample. It is established that the gradient structure formed by implantation consists of 5 layers: 1 –oxide layer; 2 –ion-implanted layer; 3 –layer with destroyed grain structure; 4 –layer of residual influence of implantation; 5 –layer corresponding to the non-implanted state of the alloy. n each layer, the phase composition, shape and location of particles of second phases were determined, the grain sizes of -Ti, the sizes, distribution density and volume fractions of released par-ticles were measured, and the state of the solid solution was analyzed. At each irradiation dose, the aluminum distri-bution along the depth of the modified layers was investigated. It was found that in layer 2, irrespective of the irradi-ation dose, aluminum is mainly involved in the formation of solid solution, the remaining aluminum -in the for-mation of intermetallic phases. In layer 3 all embedded aluminum is in intermetallic phases. The aluminum content decreases with distance from the treated surface of the sample, which leads to a decrease in the volume fractions of intermetallic phases.

  • Patterns of the formation of intermetallic phases in the surface layer upon implantation of aluminum ions into fine-grained titanium

    by Alisa Nikonenko, Mikhail Slobodyan, Natalia Popova, Elena Nikonenko, Anatoly Klopotov, Alexander Potekaev, Vladislav Borodin


  • Open Access

    Structural-phase state and properties of 56GM/(W + WC(Ni)) composite alloy obtained by wire electron beam additive manufacturing

    by A. V. Nikonenko, A. V. Vorontsov, N. N. Shamarin, V. R. Utyaganova, N. L. Savchenko, A. P. Zykova

    The authors investigated the microstructure and mechanical characteristics of 56GM steel-based composite produced by wire electron-beam additive manufacturing with the addition of W + WC(Ni) powders during printing. The analysis demonstrates that 56GM/(W + WC(Ni)) composite alloy is characterised by a gradient structure consisting of 56GM base layer, 56GM – 56GM/(W + WC(Ni)) intermediate layer and 56GM/(W + WC(Ni)) composite layer. The base layer of 56GM steel is characterized by a multidirectional acicular structure, which corresponds to the ferrite-martensite state. In 56GM – 56GM/(W + WC(Ni)) intermediate layer the acicular structure becomes less pronounced. In 56GM/(W + WC(Ni)) composite layer an equiaxed grain structure is formed, with an average grain size of 8.59 μm, along the boundaries of which cracks are observed. WC particles are located mainly along the boundaries of small grains and in small quantities inside the grains themselves. It was found that 56GM/(W + WC(Ni)) composite is mainly composed of α-Fe (~80.6 vol. %), Ni (~6 vol. %), WC carbide phase (~10.3 vol. %) and γ-Fe (3 vol. %). The structure and properties of initial 56GM steel change both in the area of direct addition of alloying powder and in the underlying layers due to diffusion processes and infiltration of W + WC(Ni). Microhardness values increase from ~3.5 GPa to ~6.5 GPa with distance from the substrate to the composite layer. In uniaxial tensile tests, the ultimate tensile strength and yield strength values reached 1100 – 1200 MPa and 835 MPa in the intermediate layer, respectively.

  • Glow Discharge at Atmospheric Pressure: Radiation, Thermal Erosion, Nanoparticles

    by K. P. Savkin, D. A. Sorokin, D. V. Beloplotov, A. G. Nikolaev, M. V. Shandrikov, A. V. Nikonenko, K. A. Shcheglov

    The results of studies of a glow discharge in an argon flow at atmospheric pressure, initiated by voltage pulses with a duration of several microseconds with a frequency of 100 kHz are presented. The discharge current value varied from several tens of milliamperes to ∼1 A. The conditions when ions and atoms of cathode metal insert appeared in discharge plasma were determined. It has been shown as a result of metal atoms cooling, they stick together into nano-sized particles, which form agglomerates with characteristic dimensions from several micrometers to tens of micrometers and exposure of metal particles at atmospheric pressure leads to the formation of metal oxide powders. The prospects for using a plasma generator based on the glow discharge at atmospheric pressure as a source of ultrafine metal oxide powders have been determined.


  • The Effect of Grain Size on the Structure and Phase Composition of VТ1-0 Alloy Implanted with Aluminum Ions

    by A. V. Nikonenko, N. A. Popova, E. L. Nikonenko, I. A. Kurzina

    The structural and phase state of the surface layers of technically pure titanium (VT1-0 alloy) implanted with aluminum ions in three states (submicrocrystalline, ultrafine-grained, and fine-grained) obtained by multiple uniaxial pressing (abc pressing) followed by multipass rolling in groove rolls at room temperature and subsequent annealing at 573, 673, and 773 K for 1 h, respectively, has been studied by transmission electron microscopy and energy dispersive X-ray spectroscopy on foils cut perpendicular to the machined sample surface. Ion implantation has been performed for 8 h and 20 min at an irradiation dose of 10 × 1017 ions/cm2 and a temperature of 623 K. It has been found that the implantation led to the formation of a gradient structure consisting of five layers. For each layer, the thickness, phase composition, and shape and arrangement of second-phase particles have been determined and the α-Ti grain size and the size, distribution density, and volume fractions of separated particles have been measured. It has been established that the implantation causes the formation of Ti3Al and TiAl3 intermetallic phases. Ti3Al particles have a lamellar shape and are located inside parts of α-Ti grains, while TiAl3 particles have a rounded shape and are arranged randomly.


  • The Influence of Ion Implantation on Internal Stresses of a Submicrocrystalline VT1-0 Alloy

    by A. V. Nikonenko, N. A. Popova, A. A. Klopotov, E. L. Nikonenko, A. I. Potekaev, V. I. Borodin


  • Open Access

    Magnesium Oxide Powder Synthesis in Cathodic Arc Discharge Plasma in an Argon Environment at Atmospheric Pressure

    by Dmitry Sorokin, Konstantin Savkin, Dmitry Beloplotov, Viktor Semin, Andrey Kazakov, Alisa Nikonenko, Alexander Cherkasov, Konstantin Shcheglov

    Discharges with cathode spots can operate in a wide range of gas pressures. Erosion of the cathode material is an inherent property of such discharges. The erosion products are considered to be ionized atoms and electrically neutral microdroplets. In accordance with this concept, a plasma source based on a pulsed cathodic arc discharge in atmospheric-pressure argon with a current of up to 200 A, a pulse duration of 250 μs, and a pulse repetition rate of 10 Hz was implemented. Using this source, the synthesis of magnesium oxide powder was performed. The chemical composition of the erosion products was determined using the TEM/EDS method and the composition of the gas mixture in which the discharge system operated was evaluated by optical spectrometry. It was shown that particles of the synthesized powder have different morphological features, depending on the nature of the electrical erosion of the cathode material. Micron-sized particles are formed due to the removal of microdroplets from liquid–metal craters on the cathode surface at certain plasma pressures. Submicron particles are produced during the agglomeration of atoms originating from the plasma jets flowing out from cathode spots. These atoms are magnesium ions that are neutralized by collisions with gas particles. The advantages and disadvantages of this synthesis method are discussed in this paper. The reference methods for the powder synthesis of magnesium oxide are compared. The prospects of the studied method from the point of view of its application for obtaining ceramic materials are also evaluated.


  • Open Access

    ВЛИЯНИЕ РАЗМЕРА ЗЕРНА НА СТРУКТУРУ И ФАЗОВЫЙ СОСТАВ СПЛАВА ВТ1-0, ИМПЛАНТИРОВАННОГО ИОНАМИ АЛЮМИНИЯ

    by Алиса Владимировна Никоненко, Наталья Анатольевна Попова, Елена Леонидовна Никоненко, Ирина Александровна Курзина

    Методом просвечивающей электронной дифракционной микроскопии и энергодисперсионной рентгеновской спектроскопии на фольгах, вырезанных перпендикулярно обработанной поверхности образца, проведено исследование структурно-фазового состояния поверхностных слоев имплантированного ионами алюминия технически чистого титана (сплав марки ВТ1-0) в трех состояниях: субмикрокристаллическом, ультрамелкозернистом и мелкозернистом, полученных после комбинированного метода многократного одноосного прессования (аbc-прессование) с последующей многоходовой прокаткой в ручьевых валках при комнатной температуре и последующего отжига соответственно при 573, 673 и 773 К, 1 час. Ионная имплантация проводилась в течение 8 часов 20 минут, дозе облучения 10×1017 ион/см2 и температуре 623 К. Установлено, что имплантация привела к формированию градиентной структуры состоящей из 5 слоев. Для каждого слоя определена его толщина, фазовый состав, форма и расположение частиц вторых фаз, измерены размеры зерен a-Ti, размеры, плотность распределения и объемные доли выделившихся частиц. Установлено, что имплантация привела к образованию интерметаллидных фаз Ti3Al и TiAl3. Частицы Ti3Al обладают пластинчатой формой и располагаются внутри части зерен a-Ti, частицы TiAl3 имеют округлую форму и располагаются случайным образом.

  • Open Access

    Microstructures and Phases in Electron Beam Additively Manufactured Ti-Al-Mo-Zr-V/CuAl9Mn2 Alloy

    by Anna Zykova, Aleksandra Nikolaeva, Aleksandr Panfilov, Andrey Vorontsov, Alisa Nikonenko, Artem Dobrovolsky, Andrey Chumaevskii, Denis Gurianov, Andrey Filippov, Natalya Semenchuk, et al.

    Electron beam additive manufacturing from dissimilar metal wires was used to intermix 5, 10 and 15 vol.% of Ti-Al-Mo-Z-V titanium alloy with CuAl9Mn2 bronze on a stainless steel substrate. The resulting alloys were subjected to investigations into their microstructural, phase and mechanical characteristics. It was shown that different microstructures were formed in an alloy containing 5 vol.% titanium alloy, as well as others containing 10 and 15 vol.%. The first was characterized by structural components such as solid solution, eutectic intermetallic compound TiCu2Al and coarse grains of γ1-Al4Cu9. It had enhanced strength and demonstrated steady oxidation wear in sliding tests. The other two alloys also contained large flower-like Ti(Cu,Al)2 dendrites that appeared due to the thermal decomposition of γ1-Al4Cu9. This structural transformation resulted in catastrophic embrittlement of the composite and changing of wear mechanism from oxidative to abrasive.


  • Low-Current Discharge in a Flow of Atmospheric-Pressure Argon Under the Formation of Metal Atoms: Electric and Optical Characteristics

    by D. V. Beloplotov, A. S. Bugaev, V. I. Gushenets, A. G. Nikolaev, A. V. Nikonenko, K. P. Savkin, D. A. Sorokin, A. A. Cherkasov, M. V. Shandrikov