JTJames Tweedie

James Tweedie

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


James Tweedie has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Strain Recovery and Defect Characterization in Mg‐Implanted Homoepitaxial GaN on High‐Quality GaN Substrates

    by Yekan Wang, Kenny Huynh, Michael E. Liao, Hsuan-Ming Yu, Tingyu Bai, James Tweedie, Mathew Hayden Breckenridge, Ramon Collazo, Zlatko Sitar, Michal Bockowski, et al.

    The evolution of defects due to high‐pressure annealing of magnesium ion‐implanted epitaxial GaN grown on high‐quality GaN substrates is investigated. Changes in the implant‐induced strain are quantified as a function of annealing temperature and time. After annealing at 1300 °C for 10 min, the implant‐induced strain is fully relieved and accompanied by the presence of extended defects such as basal plane stacking faults and prismatic loops. Approximately one‐third of the original implant‐induced strain remains after annealing at 700 °C, and 5% of the original strain remains at 1000 °C for 100 min. In all cases, nearly all of the recovered strain occurs within first few minutes of annealing. A prominent increase in the asymmetric (104) triple axis X‐ray rocking curve full width at 0.01 maximum (FW0.01M) is observed after annealing at 1300 °C for 10 min. After annealing at 1300 °C for 100 min, a subsequent decrease in FW0.01M is correlated with a reduction of the extended defect density from 4 × 108 to 3 × 107 cm−2, determined through transmission electron microscope (TEM) measurements. Further reduction in the density of the extended defects by optimizing annealing temperature and time is expected to improve the performance of GaN‐based vertical power devices.


  • Modified zinc oxide absorbents for low-temperature gas desulfurisation

    by Thomas Baird, Patrick J. Denny, Robert Hoyle, Fiona McMonagle, Diane Stirling, James Tweedy

    The hydrogen sulfide absorption capacity of zinc oxide doped with first-row transtion-metal oxides (ca. 5% metal oxide loading) has been determined using a pulse reactor. The doped oxides were prepared either by impregnation of ZnO with the transition-metal nitrates or by comprecipitation of the transition-metal and zinc nitrates with ammonium/sodium carbonate. These absorbent precursors were then calcined to give the mixed oxides. Transmission electron microscopy studies of the impregnated and calcined absorbents revealed that the transition-metal oxides were finely dispersed over the ZnO as γ-Fe2O3, Co3O4 and CuO from the respective nitrate salts of these metals. The basal planes were the predominat exposed faces of the hexagonal ZnO in all the absorbents, irrespective of whether they were prepared by the coprecipitation or impregnation route. CuO and Co3O4 were not seen as separate phases in the respective calcined coprecipitated absorbents, but the particle morphology was noticeably changed after sulfidation and crystalline ZnS was detected by electron diffraction. Oxides prepared by the coprecipitation route had higher surface areas and a greater capacity for H2S removal than their impregnated counterparts. Doping with iron salts had little effect on the H2S uptake of ZnO, irrespective of whether an impregnation or a coprecipitation route had been used, but doping with copper or cobalt salts resulted in a marked enhancement in the H2S uptake in each case. The reaction of the mixed oxides with H2S was restricted to ca. 0.6 monolayers on average, based on calculations from surface areas, and is therefore largely confined to the surface of the oxides. However, the resulting sulfide is not present entirely as an adsorbed layer; some reaction occurs locally in depth to form ZnS crystallites sufficiently large to give an electron diffraction pattern. The main role of the transition-metal oxide is to increase the total surface area available for reaction with H2S.