Taoli Xiao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Taoli Xiao has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Haicheng She
School of Urban Construction, Yangtze University, Jingzhou 434032, China
2 shared publications Hao Yuan
School of Urban Construction, Yangtze University, Jingzhou, China
2 shared publicationsMei Huang
School of Urban Construction, Yangtze University, Jingzhou, China
2 shared publications- Min Gao
State Key Laboratory of Coastal and Offshore Engineering
2 shared publications Yuanlong Zheng
Yangtze University
2 shared publications- Yunlong He
School of Urban Construction
2 shared publications
Latest Publications
- Open Access
- 19 April 2023
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 11
Influence of coplanar double fissures on failure characteristics of sandstone and fracture mechanics analysis
The influence of fissure angles and bridge lengths on rock mechanical properties and failure was analyzed using the uniaxial compression test and the Digital Image Correlation (DIC) technique. The research findings are as follows: 1) Peak stress and elastic modulus of the samples exhibited an obvious change trend with the change in fissure angle. The fissure angle has a more significant effect on a rock’s mechanical properties than the length of the rock bridge. 2) With an increase in the fissure angle, the number of surface cracks, main failure cracks and surface spalling decreased, whereas the area of the falling blocks significantly increased. However, with an increase in bridge length, the characteristics of crack propagation and spalling are essentially the same. During crack propagation, the connection of the rock bridge is related to its fissure angle and length. 3) At a low fissure angle, the failure mode of rock samples is dominated by tensile-failure cracks; with an increase in fissure angle, the tension-damage to shear-damage crack transformation will form a mixed tensile-shear damage mode; at the same time, with an increase in bridge length, the rock bridge becomes more difficult to connect, and the local crack expansion failure changes from tensile-shear cracks to tensile cracks. 4) Stress on the coplanar double-fissured rock sample was simplified and analyzed to explain the behavior of fractures on the sample. These research results have an important guiding value for engineering optimal designs.
- 19 April 2023
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 11
Open AccessInfluence of coplanar double fissures on failure characteristics of sandstone and fracture mechanics analysis
The influence of fissure angles and bridge lengths on rock mechanical properties and failure was analyzed using the uniaxial compression test and the Digital Image Correlation (DIC) technique. The research findings are as follows: 1) Peak stress and elastic modulus of the samples exhibited an obvious change trend with the change in fissure angle. The fissure angle has a more significant effect on a rock’s mechanical properties than the length of the rock bridge. 2) With an increase in the fissure angle, the number of surface cracks, main failure cracks and surface spalling decreased, whereas the area of the falling blocks significantly increased. However, with an increase in bridge length, the characteristics of crack propagation and spalling are essentially the same. During crack propagation, the connection of the rock bridge is related to its fissure angle and length. 3) At a low fissure angle, the failure mode of rock samples is dominated by tensile-failure cracks; with an increase in fissure angle, the tension-damage to shear-damage crack transformation will form a mixed tensile-shear damage mode; at the same time, with an increase in bridge length, the rock bridge becomes more difficult to connect, and the local crack expansion failure changes from tensile-shear cracks to tensile cracks. 4) Stress on the coplanar double-fissured rock sample was simplified and analyzed to explain the behavior of fractures on the sample. These research results have an important guiding value for engineering optimal designs.
- Open Access
- 11 January 2023
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 10
Crack propagation law of rock with single fissure based on PFC2D
In the study of pre-fabricated single-fissured rock, the failure mode, mechanical properties and propagation law of rock are affected by the length and inclination angle of fissure. In this study, artificially prepared marble-like rocks with different fissure characteristics were used as rock representatives, using PFC2D software to establish a uniaxial compression model tests for rocks with fissures. The effects of different fissure lengths and inclination angles on the failure mode and crack initiation and propagation of rock-like structures were systematically studied, revealing the mechanism of macroscopic mechanical behavior of rocks containing single fissures in the process of crack initiation, propagation, and failure at the micro-level. The results show that: 1) Failure mode of the rock sample is mainly controlled by fissure inclination angle and fragmentation degree is mainly controlled by fissure length. 2) The initiation stress, damage stress, and peak stress of rock samples during loading deformation increase with the increase of fissure inclination angle, and decrease with the increase of fissure length. The crack initiation angle decreases with the increase of the fissure inclination angle. 3) Crack initiation characteristics: at a low fissure inclination angle (α< 45°), the crack initiation position has a certain offset to the center of the prefabricated fissure, or starts from the tip of the prefabricated fissure. At high fissure inclination angles (α≥45°), the crack initiates from the tip of the prefabricated fissure and forms a “dispersed” distribution. 4) The crack propagation law is mainly shear cracks, at a low fissure inclination angle (α< 45°), the crack propagation has obvious aggregation band formation. At high fissure inclination angles (α≥45°), the crack aggregation zone gradually weakened and expanded in the direction of dispersion.
- 11 January 2023
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 10
Open AccessCrack propagation law of rock with single fissure based on PFC2D
In the study of pre-fabricated single-fissured rock, the failure mode, mechanical properties and propagation law of rock are affected by the length and inclination angle of fissure. In this study, artificially prepared marble-like rocks with different fissure characteristics were used as rock representatives, using PFC2D software to establish a uniaxial compression model tests for rocks with fissures. The effects of different fissure lengths and inclination angles on the failure mode and crack initiation and propagation of rock-like structures were systematically studied, revealing the mechanism of macroscopic mechanical behavior of rocks containing single fissures in the process of crack initiation, propagation, and failure at the micro-level. The results show that: 1) Failure mode of the rock sample is mainly controlled by fissure inclination angle and fragmentation degree is mainly controlled by fissure length. 2) The initiation stress, damage stress, and peak stress of rock samples during loading deformation increase with the increase of fissure inclination angle, and decrease with the increase of fissure length. The crack initiation angle decreases with the increase of the fissure inclination angle. 3) Crack initiation characteristics: at a low fissure inclination angle (α< 45°), the crack initiation position has a certain offset to the center of the prefabricated fissure, or starts from the tip of the prefabricated fissure. At high fissure inclination angles (α≥45°), the crack initiates from the tip of the prefabricated fissure and forms a “dispersed” distribution. 4) The crack propagation law is mainly shear cracks, at a low fissure inclination angle (α< 45°), the crack propagation has obvious aggregation band formation. At high fissure inclination angles (α≥45°), the crack aggregation zone gradually weakened and expanded in the direction of dispersion.
- Open Access
- 6 January 2023
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 10
Mechanical properties and failure law of composite rock containing two coplanar fractures
Composite rocks comprise the rock structures that are commonly used in geotechnical engineering. The fracture configuration has a substantial influence on the mechanical behavior, failure mode, and crack propagation of composite rocks. In this study, we considered a composite rock with two prefabricated coplanar fractures. Through laboratory uniaxial compression tests and using a digital image acquisition system, we systematically studied the effects of different fracture lengths and inclination angles on the mechanical properties and failure characteristics of the rocks. We obtained the following results: 1) during the loading deformation of the rock sample, the peak stress and elastic modulus increased with an increase in the fracture inclination angle and decreased with an increase in the fracture length. The deterioration coefficient k (the ratio of the difference between the peak strength of intact and fractured rock sample to that of intact rock sample) decreased with an increase in the fracture inclination angle and increased with an increase in the fracture length. 2) The failure type of the rock samples was primarily controlled by the fracture inclination angle and material of the two rock types, and the fragmentation degree was primarily controlled by the fracture length. With an increase in the fracture inclination angle, the failure mode of rock sample exhibited the following order of changes leading to failure: a double-Y type (trwo wing and one antiwing cracks appeared on each prefabricated fracture) → double-Z type (two wing cracks appeared on each prefabricated fracture) → Z type (one wing crack appeared on each prefabricated fracture). 3) The type of coalescence of the rock bridge was controlled by the fracture inclination angle and structural plane. The crack positions were primarily affected by the fracture length. 4) At a low fracture inclination angle (α ≤ 30°), the propagation of the microcracks showed aggregated band formation. Above moderate fracture inclination angles (α > 30°), the microcrack aggregation band gradually weakened and expanded in the direction of dispersion.
- 6 January 2023
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 10
Open AccessMechanical properties and failure law of composite rock containing two coplanar fractures
Composite rocks comprise the rock structures that are commonly used in geotechnical engineering. The fracture configuration has a substantial influence on the mechanical behavior, failure mode, and crack propagation of composite rocks. In this study, we considered a composite rock with two prefabricated coplanar fractures. Through laboratory uniaxial compression tests and using a digital image acquisition system, we systematically studied the effects of different fracture lengths and inclination angles on the mechanical properties and failure characteristics of the rocks. We obtained the following results: 1) during the loading deformation of the rock sample, the peak stress and elastic modulus increased with an increase in the fracture inclination angle and decreased with an increase in the fracture length. The deterioration coefficient k (the ratio of the difference between the peak strength of intact and fractured rock sample to that of intact rock sample) decreased with an increase in the fracture inclination angle and increased with an increase in the fracture length. 2) The failure type of the rock samples was primarily controlled by the fracture inclination angle and material of the two rock types, and the fragmentation degree was primarily controlled by the fracture length. With an increase in the fracture inclination angle, the failure mode of rock sample exhibited the following order of changes leading to failure: a double-Y type (trwo wing and one antiwing cracks appeared on each prefabricated fracture) → double-Z type (two wing cracks appeared on each prefabricated fracture) → Z type (one wing crack appeared on each prefabricated fracture). 3) The type of coalescence of the rock bridge was controlled by the fracture inclination angle and structural plane. The crack positions were primarily affected by the fracture length. 4) At a low fracture inclination angle (α ≤ 30°), the propagation of the microcracks showed aggregated band formation. Above moderate fracture inclination angles (α > 30°), the microcrack aggregation band gradually weakened and expanded in the direction of dispersion.
- Open Access
- 1 January 2021
- Published by Wiley in Shock and Vibration
- Vol. 2021 (1)
Estimating the Basal Heave Stability of Narrow Braced Excavations
Engineering practices indicate that narrow braced excavation exhibits a clear size effect. However, the slip circle method in the design codes fails to consider the effect of excavation width on basal heave stability, causing waste for narrow excavation. In this paper, numerical simulation for basal heave failure of excavation with different widths was performed by FEM with SSRT (shear strength reduction technique). The results revealed that the failure mechanism of narrow excavation is different from the complete slip circle mode. In addition, the safety factor decreases increasingly slowly as the excavation widens and stabilizes when approaching the critical width. Subsequently, the corresponding computation model was presented, and an improved SCM (slip circle method) was further developed. Finally, the engineering case illustrated that it can effectively optimize the design, which exhibits clear superiority.
- 1 January 2021
- Published by Wiley in Shock and Vibration
- Vol. 2021 (1)
Open AccessEstimating the Basal Heave Stability of Narrow Braced Excavations
Engineering practices indicate that narrow braced excavation exhibits a clear size effect. However, the slip circle method in the design codes fails to consider the effect of excavation width on basal heave stability, causing waste for narrow excavation. In this paper, numerical simulation for basal heave failure of excavation with different widths was performed by FEM with SSRT (shear strength reduction technique). The results revealed that the failure mechanism of narrow excavation is different from the complete slip circle mode. In addition, the safety factor decreases increasingly slowly as the excavation widens and stabilizes when approaching the critical width. Subsequently, the corresponding computation model was presented, and an improved SCM (slip circle method) was further developed. Finally, the engineering case illustrated that it can effectively optimize the design, which exhibits clear superiority.
- Open Access
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Experimental and Numerical Studies on the Inflatable Recyclable Anchor in the Tube Piece Type Based on the Soil‐Anchor Interaction Mechanism
This paper deeply studies the characteristics and “uplift bearing capacity” of a novel type of inflatable recyclable anchor in the tube piece. The proposed novel inflatable recyclable anchor in the tube piece type comprises a metallic rod, an inflatable anchorage device, and a recovery device. Fifteen field uplift tests are conducted to investigate the effects of inflation pressure, thickness of the steel disc, embedment length, and time lapse between anchor inflation and pullout on “the uplift bearing capacity.” The results show that “the uplift bearing capacity” of the novel inflatable anchor in the tube piece type increases with the increase of inflation pressure, thickness of the steel disc, and embedment length. With the increase of inflation time, “the uplift bearing capacity” of the novel inflatable anchor experiences an increase after first experiencing a decrease. The finite element analysis method is used to establish a numerical analysis model of the inflatable anchor, and the distribution law of the tensile stress of the surrounding soil during the pullout of the anchor is analysed. Compared with the traditional grouted anchor, the proposed anchor has an obvious superiority in recyclability, reusability, and swifter formation of anchorage force and thus is a resource‐saving and environmentally friendly anchor technology.
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Open AccessExperimental and Numerical Studies on the Inflatable Recyclable Anchor in the Tube Piece Type Based on the Soil‐Anchor Interaction Mechanism
This paper deeply studies the characteristics and “uplift bearing capacity” of a novel type of inflatable recyclable anchor in the tube piece. The proposed novel inflatable recyclable anchor in the tube piece type comprises a metallic rod, an inflatable anchorage device, and a recovery device. Fifteen field uplift tests are conducted to investigate the effects of inflation pressure, thickness of the steel disc, embedment length, and time lapse between anchor inflation and pullout on “the uplift bearing capacity.” The results show that “the uplift bearing capacity” of the novel inflatable anchor in the tube piece type increases with the increase of inflation pressure, thickness of the steel disc, and embedment length. With the increase of inflation time, “the uplift bearing capacity” of the novel inflatable anchor experiences an increase after first experiencing a decrease. The finite element analysis method is used to establish a numerical analysis model of the inflatable anchor, and the distribution law of the tensile stress of the surrounding soil during the pullout of the anchor is analysed. Compared with the traditional grouted anchor, the proposed anchor has an obvious superiority in recyclability, reusability, and swifter formation of anchorage force and thus is a resource‐saving and environmentally friendly anchor technology.
- Open Access
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
The Prediction of Pile Foundation Buried Depth Based on BP Neural Network Optimized by Quantum Particle Swarm Optimization
Due to the fluctuation of the bearing stratum and the distinct properties of the soil layer, the buried depth of the pile foundation will differ from each other as well. In practical construction, since the designed pile length is not definitely consistent with the actual pile length, masses of piles will be required to be cut off or supplemented, resulting in huge cost waste and potential safety hazards. Accordingly, the prediction of pile foundation buried depth is of great significance in construction engineering. In this paper, a nonlinear model based on coordinates and buried depth of piles was established by the BP neural network to predict the samples to be evaluated, the consequence of which indicated that the BP neural network was easily trapped in local extreme value, and the error reached 31%. Afterwards, the QPSO algorithm was proposed to optimize the weights and thresholds of the BP network, which showed that the minimum error of QPSO‐BP was merely 9.4% in predicting the depth of bearing stratum and 2.9% in predicting the buried depth of pile foundation. Besides, this paper compared QPSO‐BP with three other robust models referred to as FWA‐BP, PSO‐BP, and BP by three statistical tests (RMSE, MAE, and MAPE). The accuracy of the QPSO‐BP algorithm was the highest, which demonstrated the superiority of QPSO‐BP in practical engineering.
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Open AccessThe Prediction of Pile Foundation Buried Depth Based on BP Neural Network Optimized by Quantum Particle Swarm Optimization
Due to the fluctuation of the bearing stratum and the distinct properties of the soil layer, the buried depth of the pile foundation will differ from each other as well. In practical construction, since the designed pile length is not definitely consistent with the actual pile length, masses of piles will be required to be cut off or supplemented, resulting in huge cost waste and potential safety hazards. Accordingly, the prediction of pile foundation buried depth is of great significance in construction engineering. In this paper, a nonlinear model based on coordinates and buried depth of piles was established by the BP neural network to predict the samples to be evaluated, the consequence of which indicated that the BP neural network was easily trapped in local extreme value, and the error reached 31%. Afterwards, the QPSO algorithm was proposed to optimize the weights and thresholds of the BP network, which showed that the minimum error of QPSO‐BP was merely 9.4% in predicting the depth of bearing stratum and 2.9% in predicting the buried depth of pile foundation. Besides, this paper compared QPSO‐BP with three other robust models referred to as FWA‐BP, PSO‐BP, and BP by three statistical tests (RMSE, MAE, and MAPE). The accuracy of the QPSO‐BP algorithm was the highest, which demonstrated the superiority of QPSO‐BP in practical engineering.
- Open Access
- 16 July 2020
- Published by Wiley in Shock and Vibration
- Vol. 2020, 1-12
Triaxial Permeability Experimental Study on Deformation and Failure Processes of Single-Fractured Rock Specimens
A series of rock-like specimens with specific sizes and fracture inclinations was created in the laboratory. The different effects of seepage pressure on the deformation and failure characteristics between a conventional triaxial compression test and a triaxial permeability test were studied using a servo-controlled testing machine. Furthermore, the change in the permeability of single-fractured specimens was explored based on a triaxial permeability test. The results were as follows. Compared with those observed in the conventional triaxial compression test, the peak stress and corresponding axial strain decrease under seepage pressure in the triaxial permeability test, while the deformation modulus increased. With the increase of fracture length, the peak stress of specimen decreases due to the seepage pressure and the specimen showed tensile failure horizontally. The failure mode of the single-fractured specimens was changed by the seepage pressure. A closed relationship was observed between the failure modes and the permeability-stress curves. A shear failure along the crack surface will occur when the permeability abruptly changed later than the peak stress point. The dramatic change in the permeability indicated that the permeability channel was extended or new seepage paths were created. These conclusions can provide a valuable theoretical reference for the numerical simulation of excavation and design in stability analysis of jointed rock masses.
- 16 July 2020
- Published by Wiley in Shock and Vibration
- Vol. 2020, 1-12
Open AccessTriaxial Permeability Experimental Study on Deformation and Failure Processes of Single-Fractured Rock Specimens
A series of rock-like specimens with specific sizes and fracture inclinations was created in the laboratory. The different effects of seepage pressure on the deformation and failure characteristics between a conventional triaxial compression test and a triaxial permeability test were studied using a servo-controlled testing machine. Furthermore, the change in the permeability of single-fractured specimens was explored based on a triaxial permeability test. The results were as follows. Compared with those observed in the conventional triaxial compression test, the peak stress and corresponding axial strain decrease under seepage pressure in the triaxial permeability test, while the deformation modulus increased. With the increase of fracture length, the peak stress of specimen decreases due to the seepage pressure and the specimen showed tensile failure horizontally. The failure mode of the single-fractured specimens was changed by the seepage pressure. A closed relationship was observed between the failure modes and the permeability-stress curves. A shear failure along the crack surface will occur when the permeability abruptly changed later than the peak stress point. The dramatic change in the permeability indicated that the permeability channel was extended or new seepage paths were created. These conclusions can provide a valuable theoretical reference for the numerical simulation of excavation and design in stability analysis of jointed rock masses.
- Open Access
- 1 January 2020
- Published by Wiley in Advances in Civil Engineering
- Vol. 2020 (1)
Experimental Study of the Mechanical Characteristics of a Rock‐Like Material Containing a Preexisting Fissure under Loading and Unloading Triaxial Compression
An experimental study of a rock‐like material containing a preexisting fissure subjected to loading and unloading triaxial compression is carried out, and the results show that the mechanical characteristics of the rock‐like specimen depend heavily on the loading paths and the inclination of the fissure. The triaxial loading experiment results show that the failure strength linearly increases, while the residual strength linearly decreases with increasing inclination. Furthermore, specimens subjected to triaxial compression show an “X”‐type shear failure mode. The triaxial unloading compression experimental results show that specimens with different inclination angles have various failure modes. Specimens with gentle inclinations show a tensile‐shear mix failure mode, specimens with middle inclinations show a shear‐sliding failure mode, and specimens with steep inclinations show a tensile failure mode. These findings can be used to forecast excavation‐induced instabilities in deep underground engineering rock structures.
- 1 January 2020
- Published by Wiley in Advances in Civil Engineering
- Vol. 2020 (1)
Open AccessExperimental Study of the Mechanical Characteristics of a Rock‐Like Material Containing a Preexisting Fissure under Loading and Unloading Triaxial Compression
An experimental study of a rock‐like material containing a preexisting fissure subjected to loading and unloading triaxial compression is carried out, and the results show that the mechanical characteristics of the rock‐like specimen depend heavily on the loading paths and the inclination of the fissure. The triaxial loading experiment results show that the failure strength linearly increases, while the residual strength linearly decreases with increasing inclination. Furthermore, specimens subjected to triaxial compression show an “X”‐type shear failure mode. The triaxial unloading compression experimental results show that specimens with different inclination angles have various failure modes. Specimens with gentle inclinations show a tensile‐shear mix failure mode, specimens with middle inclinations show a shear‐sliding failure mode, and specimens with steep inclinations show a tensile failure mode. These findings can be used to forecast excavation‐induced instabilities in deep underground engineering rock structures.
- Open Access
- 1 January 2018
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2018 (1)
Experimental Study of an Inflatable Recyclable Anchor
This paper describes an investigation into the performance and pullout capacity of a new inflatable anchor system embedded in deep excavation engineering. The proposed inflatable recyclable anchor system consists of a rubber pneumatic bag, movable steel plate, and force transmission bar, which can all be recycled after use. By conducting a number of field pullout tests, it is found that the pullout bearing capacity of the proposed anchor is related to the inflation pressure, the length of the rubber pneumatic bag, and the embedment depth. It is found that, with the exponential increase of inflation pressure or length of the rubber pneumatic bag, the pullout bearing capacity of the novel inflatable anchor increases exponentially. The proposed inflatable recyclable anchor can meet the bearing requirements of traditional grouted anchors. Moreover, the proposed anchor not only has better supporting effects than traditional grouted ones, but it also has the advantages of recyclability, repeated use, and rapid formation of anchorage force. It is a new green and low‐carbon anchorage, so it will have good application prospects in temporary foundation pit slope engineering.
- 1 January 2018
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2018 (1)
Open AccessExperimental Study of an Inflatable Recyclable Anchor
This paper describes an investigation into the performance and pullout capacity of a new inflatable anchor system embedded in deep excavation engineering. The proposed inflatable recyclable anchor system consists of a rubber pneumatic bag, movable steel plate, and force transmission bar, which can all be recycled after use. By conducting a number of field pullout tests, it is found that the pullout bearing capacity of the proposed anchor is related to the inflation pressure, the length of the rubber pneumatic bag, and the embedment depth. It is found that, with the exponential increase of inflation pressure or length of the rubber pneumatic bag, the pullout bearing capacity of the novel inflatable anchor increases exponentially. The proposed inflatable recyclable anchor can meet the bearing requirements of traditional grouted anchors. Moreover, the proposed anchor not only has better supporting effects than traditional grouted ones, but it also has the advantages of recyclability, repeated use, and rapid formation of anchorage force. It is a new green and low‐carbon anchorage, so it will have good application prospects in temporary foundation pit slope engineering.