Hanli Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hanli Wu has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Jenny Liu
6 shared publicationsXiong Zhang
Department of Civil, Architectural, and Environmental Engineering, Missouri University of Science and Technology, Rolla, MO
3 shared publications- Seangkru Sreng2 shared publications
Anyou Zhu
1 shared publicationChen Li
1 shared publicationDawei Wang
1 shared publication
Latest Publications
- 28 October 2026
- Published by Elsevier in Journal of Building Engineering
- Vol. 133
Automated detection of floor moisture damage via ground penetrating radar and domain adaptation
- 28 October 2026
- Published by Elsevier in Journal of Building Engineering
- Vol. 133
Automated detection of floor moisture damage via ground penetrating radar and domain adaptation
- 27 September 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 407
Effectiveness of the different eutectic phase-change materials in cooling asphalt pavement
- 27 September 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 407
Effectiveness of the different eutectic phase-change materials in cooling asphalt pavement
- 3 August 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 400
Evaluation of feasibility and performance of foamed Fire-Resistant coating materials
- 3 August 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 400
Evaluation of feasibility and performance of foamed Fire-Resistant coating materials
- 6 March 2023
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2679 (1) , 382-396
Innovative Air Convection Embankment for Cold/Arctic Region Low-Volume Roads
Roadbed thaw settlement is a unique challenge for the durability of low-volume roads (LVRs) in permafrost regions. Air convection embankment (ACE) is an effective technique that acts as a semi-heat-transfer system to control temperature variation and reduce the thaw depth of subsoil. However, limited by the shortage of the necessary crushed rocks within a short distance, building an ACE in Alaska, U.S., is prohibitively expensive. Previous studies identified the feasibility of using cellular concrete for ACE and determined the optimized thickness of the cellular concrete aggregate interlayer for ACE. However, the economic efficiency and thermal and mechanical performance of the optimized, innovative cellular concrete aggregate ACE need further investigation. Therefore, two innovative cellular concrete ACEs with reasonable heights for cold/Arctic region LVRs were evaluated in this study. A thermal-mechanical coupling model was created using ANSYS Fluent and ANSYS Mechanical to evaluate the thermal and mechanical stability of the two optimized innovative cellular concrete aggregate ACEs by comparing them with a typical Alaskan flexible pavement, a silty sand/gravel embankment, and a conventional crushed-rock ACE. The fatigue damage was predicted using the elastic-based Alaska Flexible Pavement Design (AKFPD) program. A life-cycle cost analysis was conducted using AKFPD to evaluate the overall long-term economic efficiency of the cellular concrete ACEs. The results showed that cellular concrete ACE could achieve better thermal and mechanical performance with much lower embankment height than crushed-rock ACE. The cost analysis showed that the proposed cellular concrete ACEs had a significant cost advantage over the conventional crushed-rock ACE.
- 6 March 2023
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2679 (1) , 382-396
Innovative Air Convection Embankment for Cold/Arctic Region Low-Volume Roads
Roadbed thaw settlement is a unique challenge for the durability of low-volume roads (LVRs) in permafrost regions. Air convection embankment (ACE) is an effective technique that acts as a semi-heat-transfer system to control temperature variation and reduce the thaw depth of subsoil. However, limited by the shortage of the necessary crushed rocks within a short distance, building an ACE in Alaska, U.S., is prohibitively expensive. Previous studies identified the feasibility of using cellular concrete for ACE and determined the optimized thickness of the cellular concrete aggregate interlayer for ACE. However, the economic efficiency and thermal and mechanical performance of the optimized, innovative cellular concrete aggregate ACE need further investigation. Therefore, two innovative cellular concrete ACEs with reasonable heights for cold/Arctic region LVRs were evaluated in this study. A thermal-mechanical coupling model was created using ANSYS Fluent and ANSYS Mechanical to evaluate the thermal and mechanical stability of the two optimized innovative cellular concrete aggregate ACEs by comparing them with a typical Alaskan flexible pavement, a silty sand/gravel embankment, and a conventional crushed-rock ACE. The fatigue damage was predicted using the elastic-based Alaska Flexible Pavement Design (AKFPD) program. A life-cycle cost analysis was conducted using AKFPD to evaluate the overall long-term economic efficiency of the cellular concrete ACEs. The results showed that cellular concrete ACE could achieve better thermal and mechanical performance with much lower embankment height than crushed-rock ACE. The cost analysis showed that the proposed cellular concrete ACEs had a significant cost advantage over the conventional crushed-rock ACE.
- 9 June 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2676 (12) , 760-774
Impacts of Lightweight Aggregate Interlayers for Air Convection Embankment on Pavement Thermal Profile and Pavement Performance in Alaskan Permafrost Regions
Crushed-rock air convection embankment (ACE) has been used to mitigate pavement distresses caused by climatic extremes in permafrost regions for more than three decades. This study proposes using lightweight aggregates as cost-effective alternative materials to overcome the shortage of desired crushed rocks needed for ACE in interior Alaska. This paper presents an investigation of the performance of six selected pavement structures: an asphalt pavement typical of the northern region of Alaska and five pavements reinforced with different paving interlayers (i.e., silty sand/gravel, crushed rocks, cellular concrete aggregate, foam glass aggregate, and lightweight expanded clay aggregate). Pavement thermal analyses using Temperature Estimate Model for Pavement Structures (TEMPS) program and ANSYS Fluent software were performed to predict heat transfer patterns and thermal performance for each case. Pavement performance analyses using viscoelastic-based FlexPAVE™ and the elastic-based Alaska Flexible Pavement Design (AKFPD) program were conducted to evaluate the long-term performance and structural stability of subgrade soil with different types of interlayers. The results showed that the lightweight aggregate ACEs improved cooling performance more effectively than the crushed-rock ACE. The lightweight aggregate interlayers could maintain desired thermal insulation in summer and enhance the cooling effect in winter. The modeling results identified the high potential of using lightweight aggregates as alternative ACE materials to improve pavement service life and subgrade stability.
- 9 June 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2676 (12) , 760-774
Impacts of Lightweight Aggregate Interlayers for Air Convection Embankment on Pavement Thermal Profile and Pavement Performance in Alaskan Permafrost Regions
Crushed-rock air convection embankment (ACE) has been used to mitigate pavement distresses caused by climatic extremes in permafrost regions for more than three decades. This study proposes using lightweight aggregates as cost-effective alternative materials to overcome the shortage of desired crushed rocks needed for ACE in interior Alaska. This paper presents an investigation of the performance of six selected pavement structures: an asphalt pavement typical of the northern region of Alaska and five pavements reinforced with different paving interlayers (i.e., silty sand/gravel, crushed rocks, cellular concrete aggregate, foam glass aggregate, and lightweight expanded clay aggregate). Pavement thermal analyses using Temperature Estimate Model for Pavement Structures (TEMPS) program and ANSYS Fluent software were performed to predict heat transfer patterns and thermal performance for each case. Pavement performance analyses using viscoelastic-based FlexPAVE™ and the elastic-based Alaska Flexible Pavement Design (AKFPD) program were conducted to evaluate the long-term performance and structural stability of subgrade soil with different types of interlayers. The results showed that the lightweight aggregate ACEs improved cooling performance more effectively than the crushed-rock ACE. The lightweight aggregate interlayers could maintain desired thermal insulation in summer and enhance the cooling effect in winter. The modeling results identified the high potential of using lightweight aggregates as alternative ACE materials to improve pavement service life and subgrade stability.
- 5 September 2020
- Published by Springer Nature in Frontiers of Structural and Civil Engineering
- Vol. 14 (5) , 1232-1246
A filtering-based bridge weigh-in-motion system on a continuous multi-girder bridge considering the influence lines of different lanes
- 5 September 2020
- Published by Springer Nature in Frontiers of Structural and Civil Engineering
- Vol. 14 (5) , 1232-1246
A filtering-based bridge weigh-in-motion system on a continuous multi-girder bridge considering the influence lines of different lanes