Jian Zheng

The evaluation of sweet spots for infill wells is critical to identifying premium reservoir zones, avoiding fracture hits, and achieving safe, efficient development with maximum production potential. Firstly, considering that geological and engineering factors—such as high fracability and good reservoir quality—are conducive to the formation of complex fracture networks and sufficient gas production after fracturing, quantitative evaluation indicators for fracability and geological properties have been established. Secondly, a classification method for different sweet spot tiers in infill wells was proposed. Lastly, taking the Changning infill pilot wells as an example, for sections not affected by fracture interference, higher sweet spot evaluation scores show a strong correlation with improved predictive performance of tracer-based gas production forecasts. Conversely, in fracture-interfered zones, a discrepancy was observed between the sweet spot evaluation results and actual gas production volumes. The horizontal wellbores were classified into a six-tier system (L1–L6), with tailored fracturing design recommendations provided accordingly. This study offers scientific guidance for the precise evaluation of sweet spots in infill wells and the design of customized staged fracturing, thereby significantly enhancing fracturing effectiveness.

Numerous uncertainties persist regarding the differential enrichment mechanisms of shale gas reservoirs in southern China. This investigation systematically examines the sedimentary environments and reservoir characteristics of the Wufeng–Longmaxi formations in the Changning area of the Sichuan Basin, through the integration of comprehensive drilling data, core samples, and analytical measurements. Multivariate sedimentary proxies (including redox conditions, terrigenous detrital influx, basinal water restriction, paleoclimatic parameters, paleowater depth variations, and paleo-marine productivity) were employed to elucidate environmental controls on reservoir development. The research findings demonstrate that during the depositional period of the Wufeng Formation in the Changning area, the bottom water was characterized by suboxic to anoxic conditions under a warm-humid paleoclimate, with limited terrigenous detrital input and strong water column restriction throughout the interval. Within the Longmaxi Formation, the depositional environment evolved from intensely anoxic conditions in the LM1 through suboxic states in the LM3 interval, approaching toxic conditions by the LM2 depositional phase. Concurrently, the paleoclimate transitioned towards warmer and more humid conditions, accompanied by progressively intensified terrigenous input from the LM1-LM6, while maintaining semi-restricted water circulation. Both paleowater depth and paleoproductivity peaked from the Wufeng Formation to the LM1 interval, followed by gradual shallowing of water depth and declining productivity during the LM3–LM6 depositional phases. Comparative analysis of depositional environments and reservoir characteristics reveals that sedimentary conditions exert a controlling influence on multiple reservoir parameters, including shale mineral composition, organic matter enrichment, pore architecture, petrophysical properties (e.g., porosity, permeability), and gas-bearing potential.

Nowadays, most oilfields have entered the high water cut stage of waterflood development. The importance of oil–water separation technology becomes more obvious. Gravity separation is one of the most commonly used treatment techniques for produced fluid. The gravitational separator has a large processing capacity and a wide application range, but its structure is relatively simple and the separation efficiency gradually falls behind to meet current production needs. The key difficulties to improve the separation efficiency are to analyze the flow field and coalescing components inside the separator. Aiming at these difficulties, this paper reports an innovatively designed series-parallel multistage multiphase separation system (MMSS). A horizontal separator is connected in series with a vertical separator, and the vertical separator consists of five discrete pipes connected in parallel. Different coalescing components are then set inside the vertical separator. The separation effect of the MMSS is studied by numerical simulation and laboratory experiments. The oil phase volume distribution cloud diagrams of coalescing components are analyzed by numerical simulation, including semicircle baffle, spiral track plate, four-hole plate and seven-hole plate. Laboratory experiments show that MMSS has a high separation efficiency, and the water content at the oil outlet is 3.0% less than that of the horizontal separator. By observing the shape of oil droplets at the outlet and measuring the oil cut and water cut at the sampling outlet, the separation effect of four coalescent plates is obtained. According to the statistics, when the volumetric flow at the inlet of the separator is 1.5 m³/h, the average particle size of oil drops in the blank pipe, semicircular baffle, four-hole plate, spiral track and seven-hole plate increases in turn. A continuous oil layer appears at the outlet of the vertical separator in the fully open state. The water content at the oil outlet of the semicircular baffle coalescing component is always at a high level under different flow rates. When the inlet volumetric flow rate is less than 1.6 m³/h, the performance of the spiral track coalescing component is better. With the increase of the inlet volumetric flow rate, the separation efficiency of the spiral track is lower than that of the orifice. The results show that the semicircular coalescing component has the worst performance, the spiral track coalescing component is superior at small volumetric flow rates, and the orifice coalescing component is superior at large volumetric flow rates.

The application of horizontal wells with multistage hydraulic fracturing technologies has made the development of shale gas reservoirs become a worldwide economical hotspot in recent years. The gas transport mechanisms in shale gas reservoirs are complicated, due to the multiple types of pores with complex pore structure and special process of gas accumulation and transport. Although there have been many attempts to come up with a suitable and practical mathematical model to characterize the shale gas flow process, no unified model has yet been accepted by academia. In this paper, a comprehensive literature review on the mathematical models developed in recent years for describing gas flow in shale gas reservoirs is summarized. Five models incorporating different transport mechanisms are reviewed, including gas viscous flow in natural fractures or macropores, gas ad-desorption on shale organic, gas slippage, diffusion (Knudsen diffusion, Fick diffusion, and surface diffusion), stress dependence, real gas effect, and adsorption layer effect in the nanoshale matrix system, which is quite different from conventional gas reservoir. This review is very helpful to understand the complex gas flow behaviors in shale gas reservoirs and guide the efficient development of shale gas. In addition to the model description, we depicted the type curves of fractured horizontal well with different seepage models. From the review, it can be found that there is some misunderstanding about the essence of Knudsen/Fick diffusion and slippage, which makes different scholars adopt different weighting methods to consider them. Besides, the contribution of each mechanism on the transport mechanisms is still controversial, which needs further in-depth study in the future.

The abundant reserve of shale gas in Sichuan Basin has become a significant natural gas component in China. To achieve efficient development of shale gas, it is necessary to analyze the stress state, pore pressure, and reservoir mechanical properties such that an accurate geomechanical model can be established. In this paper, Six wells of Neijiang-Dazu and North Rongchang (NDNR) Block were thoroughly investigated to establish the geomechanical model for the study area. The well log analysis was performed to derive the in-situ stresses and pore pressure while the stress polygon was applied to constrain the value of the maximum horizontal principal stress. Image and caliper data, mini-frac test and laboratory rock mechanics test results were used to calibrate the geomechanical model. The model was further validated by comparing the model prediction against the actual wellbore failure observed in the field. It was found that it is associated with the strike-slip (SS) stress regime; the orientation of S_Hmax was inferred to be 106–130° N. The pore pressure appears to be approximately hydrostatic from the surface to 1000 m true vertical depth (TVD), but then becomes over-pressured from the Xujiahe formation. The geomechanical model can provide guidance for the subsequent drilling and completion in this area and be used to effectively avoid complex drilling events such as collapse, kick, and lost circulation (mud losses) along the entire well. Also, the in-situ stress and pore pressure database can be used to analyze wellbore stability issues as well as help design hydraulic fracturing operations.