Abdul Karim
Research Subjects
Abdul Karim has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Duck Bong Kim
School of Environmental, Civil, Agricultural, and Mechanical Engineering, University of Georgia, Athens, GA 30602, USA
3 shared publications - Yeong-Do Park
Department of Advanced Materials Engineering Dong-Eui University 47340 Busan Korea
3 shared publications - Yongho Jeon
Department of Mechanical Engineering, Ajou University, Suwon 16499, Republic of Korea
3 shared publications - Mahdi Sadeqi Bajestani
UHasselt, School of Transportation Science, Transportation Research Institute (IMOB), Hasselt, Belgium
2 shared publications Saiful Islam
2 shared publicationsBehrouz Bagheri Vanani
1 shared publication
Latest Publications
- Open Access
- 30 April 2026
- Published by Elsevier in SSRN Electronic Journal
Corrosion Mechanisms of Additively Manufactured W/Steel Multi-Materials with Ni Interlayer: Coupling Experiments and Reactive MD Simulations
This study investigates the corrosion behavior and mechanical performance of multi-material structures composed of W7Ni3Fe tungsten alloy and 316L stainless steel (SS316L) with an Inconel 625 (IN625) interlayer, designed for application in corrosive environments. The structure was fabricated using wire-arc directed energy deposition (DED) followed by heat treatment at 900 °C for 2 hours with furnace cooling. ReaxFF Molecular Dynamics (MD) was considered to study the mechanism of interface corrosion in 3.5 wt.% NaCl solution for a duration of 500, 1000, and 1500 hours. Long-term immersion tests in 3.5 wt.% NaCl solution revealed a decreasing corrosion rate—from 9.34 × 10⁻³ mm/year after 500 hours to 6.77 × 10⁻³ mm/year after 1500 hours—indicating progressive surface passivation. Surface analysis identified WO₂, Fe₃O₄, and Cr₂O₃ as dominant corrosion products. Electrochemical tests showed that IN625 interlayer exhibited the most noble behavior (Ecorr = −223 mV, Icorr = 1.4 µA/cm²), followed by SS316L and W7Ni3Fe. The overall corrosion rate estimated from Icorr was 18.8 × 10⁻³ mm/year, moderately matching the mass-loss-based corrosion rates. The MD simulations confirmed the experimental surface analysis and indicated that an increasing number of oxygens, OH, and chloride ions accumulate at the surface and participate in the corrosion process as the simulation progresses. Mechanical testing indicated that the ultimate tensile strength decreased by 7.3%, from 602 ± 7 MPa before immersion to 558 ± 8 MPa after 1500 hours of immersion, confirming that the structure retained most of its mechanical integrity despite localized corrosion, particularly in the W7Ni3Fe region.
- 30 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCorrosion Mechanisms of Additively Manufactured W/Steel Multi-Materials with Ni Interlayer: Coupling Experiments and Reactive MD Simulations
This study investigates the corrosion behavior and mechanical performance of multi-material structures composed of W7Ni3Fe tungsten alloy and 316L stainless steel (SS316L) with an Inconel 625 (IN625) interlayer, designed for application in corrosive environments. The structure was fabricated using wire-arc directed energy deposition (DED) followed by heat treatment at 900 °C for 2 hours with furnace cooling. ReaxFF Molecular Dynamics (MD) was considered to study the mechanism of interface corrosion in 3.5 wt.% NaCl solution for a duration of 500, 1000, and 1500 hours. Long-term immersion tests in 3.5 wt.% NaCl solution revealed a decreasing corrosion rate—from 9.34 × 10⁻³ mm/year after 500 hours to 6.77 × 10⁻³ mm/year after 1500 hours—indicating progressive surface passivation. Surface analysis identified WO₂, Fe₃O₄, and Cr₂O₃ as dominant corrosion products. Electrochemical tests showed that IN625 interlayer exhibited the most noble behavior (Ecorr = −223 mV, Icorr = 1.4 µA/cm²), followed by SS316L and W7Ni3Fe. The overall corrosion rate estimated from Icorr was 18.8 × 10⁻³ mm/year, moderately matching the mass-loss-based corrosion rates. The MD simulations confirmed the experimental surface analysis and indicated that an increasing number of oxygens, OH, and chloride ions accumulate at the surface and participate in the corrosion process as the simulation progresses. Mechanical testing indicated that the ultimate tensile strength decreased by 7.3%, from 602 ± 7 MPa before immersion to 558 ± 8 MPa after 1500 hours of immersion, confirming that the structure retained most of its mechanical integrity despite localized corrosion, particularly in the W7Ni3Fe region.
- Open Access
- 1 October 2025
- Published by Elsevier in International Journal of Fatigue
- Vol. 203
Heat treatments for microstructure modification and mechanical properties enhancement of wire-arc additively manufactured tungsten-inconel bimetallic structures
- 1 October 2025
- Published by Elsevier in International Journal of Fatigue
- Vol. 203
Open AccessHeat treatments for microstructure modification and mechanical properties enhancement of wire-arc additively manufactured tungsten-inconel bimetallic structures
- Open Access
- 31 December 2022
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 40 (6) , 512-524
Effect of Top Sheet Materials on Joint Performance of Self-Piercing Riveting
Three types of self-piercing riveting (SPR) joints, i.e., steel/aluminum, carbon fiber reinforced polymer (CFRP)/ aluminum, and aluminum/aluminum, were constructed using three different top sheet materials with the same aluminum alloy as the bottom sheet. The effects of the top sheet material on the joint quality and mechanical behavior were evaluated. The top sheet materials’ characteristics dominate the rivet piercing process and the consequent interlock distance. The high-strength steel top sheet requires a comparatively higher rivet setting force and induces early flaring of the rivet tail, resulting in a larger interlock distance. Though the CFRP needs the highest rivet setting force to penetrate the rivet through the CFRP fibers, the CFRP/aluminum joint exhibits the smallest interlock distance because of the SPR process-induced damages to the CFRP and subsequently less flaring of the rivet tail. In strength tests, the damaged CFRP sheet resulted in rivet head pullout of the CFRP/aluminum joints, which exhibited the lowest lap-shear and cross-tension strengths. In contrast, the steel/aluminum joints demonstrated the highest strengths because of their comparatively larger interlock distances. In addition to the experimental analysis, simulations revealed the rivet penetration and flaring mechanisms with various top sheet materials, and their respective joint quality and strengths.
- 31 December 2022
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 40 (6) , 512-524
Open AccessEffect of Top Sheet Materials on Joint Performance of Self-Piercing Riveting
Three types of self-piercing riveting (SPR) joints, i.e., steel/aluminum, carbon fiber reinforced polymer (CFRP)/ aluminum, and aluminum/aluminum, were constructed using three different top sheet materials with the same aluminum alloy as the bottom sheet. The effects of the top sheet material on the joint quality and mechanical behavior were evaluated. The top sheet materials’ characteristics dominate the rivet piercing process and the consequent interlock distance. The high-strength steel top sheet requires a comparatively higher rivet setting force and induces early flaring of the rivet tail, resulting in a larger interlock distance. Though the CFRP needs the highest rivet setting force to penetrate the rivet through the CFRP fibers, the CFRP/aluminum joint exhibits the smallest interlock distance because of the SPR process-induced damages to the CFRP and subsequently less flaring of the rivet tail. In strength tests, the damaged CFRP sheet resulted in rivet head pullout of the CFRP/aluminum joints, which exhibited the lowest lap-shear and cross-tension strengths. In contrast, the steel/aluminum joints demonstrated the highest strengths because of their comparatively larger interlock distances. In addition to the experimental analysis, simulations revealed the rivet penetration and flaring mechanisms with various top sheet materials, and their respective joint quality and strengths.
- Open Access
- 29 February 2020
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 38 (1) , 8-23
A Review on Welding of Dissimilar Metals in Car Body Manufacturing
- 29 February 2020
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 38 (1) , 8-23
Open AccessA Review on Welding of Dissimilar Metals in Car Body Manufacturing