Datong Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Datong Wu has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
G. Busse
8 shared publicationsGerhard Busse
Univ. Stuttgart (Germany)
5 shared publications- Christian Ulrich Grosse
Technical University of Munich
4 shared publications W. Karpen
4 shared publicationsJ. Rantala
3 shared publicationsA. Salerno
Univ. Stuttgart (Germany)
2 shared publications
Latest Publications
- Open Access
- 1 November 2025
- Published by NDT.net GmbH & Co. KG
- Vol. 30 (12)
Low-Cost Lock-In-Thermography System for Educational Use
We present a cost-efficient lock-in thermography platform built from an industrial OEM micro-bolometer and LED excitation, aimed at teaching laboratories and budget-constrained NDT. The system is benchmarked against a scientific-grade thermal imager on three specimens: (i) a carbon-fiber composite plate with impact-induced delamination, (ii) a PVC flat-bottom-hole phantom with controlled diameter and remaining wall thickness, and (iii) a PVC double-hole feature from literature. Identical preprocessing and FFT-based demodulation are used for both systems; complementary 3D time-domain simulations (COMSOL) support interpretation. Across 0.01–1 Hz, the low-cost setup reproduces defect morphology and phase trends observed with the reference, including frequency-dependent phase behavior consistent with thermal-wave depth sensitivity. Quantitatively, phase contrast is lower for the low-cost system and approaches the detection limit at higher modulation frequencies, as expected from diffusion-length scaling. The strongest agreement is in phase, with amplitude discrepancies attributable to excitation non-uniformity and simplified loss modeling. We conclude that the platform is well suited for education and shows promise for targeted industrial screening with modest hardware and processing upgrades.
- 1 November 2025
- Published by NDT.net GmbH & Co. KG
- Vol. 30 (12)
Open AccessLow-Cost Lock-In-Thermography System for Educational Use
We present a cost-efficient lock-in thermography platform built from an industrial OEM micro-bolometer and LED excitation, aimed at teaching laboratories and budget-constrained NDT. The system is benchmarked against a scientific-grade thermal imager on three specimens: (i) a carbon-fiber composite plate with impact-induced delamination, (ii) a PVC flat-bottom-hole phantom with controlled diameter and remaining wall thickness, and (iii) a PVC double-hole feature from literature. Identical preprocessing and FFT-based demodulation are used for both systems; complementary 3D time-domain simulations (COMSOL) support interpretation. Across 0.01–1 Hz, the low-cost setup reproduces defect morphology and phase trends observed with the reference, including frequency-dependent phase behavior consistent with thermal-wave depth sensitivity. Quantitatively, phase contrast is lower for the low-cost system and approaches the detection limit at higher modulation frequencies, as expected from diffusion-length scaling. The strongest agreement is in phase, with amplitude discrepancies attributable to excitation non-uniformity and simplified loss modeling. We conclude that the platform is well suited for education and shows promise for targeted industrial screening with modest hardware and processing upgrades.
- Open Access
THz-TDS Reflection Measurement of Coating Thicknesses at Non-Perpendicular Incidence: Experiment and Simulation
Time-domain spectroscopy (TDS) in the terahertz (THz) frequency range is gaining in importance in nondestructive testing of dielectric materials. One application is the layer thickness measurement of a coating layer. To determine the thickness from the measurement data, the refractive index of the coating layer must be known in the surveyed frequency range. For perpendicular incidence of the radiation, methods exist to extract the refractive index from the measurement data themselves without prior knowledge. This paper extends these methods for non-perpendicular incidence, where the polarization of the radiation becomes important. Furthermore, modifications considering effects of surface roughness of the coating are introduced. The new methods are verified using measurement data of a sample of Inconel steel coated with yttria-stabilized zirconia (YSZ) and with COMSOL simulations of the measurement setup. To validate the thickness measurements, scanning electron microscopy (SEM) images of the layer structure are used. The results show good agreement with an average error of 1% for the simulation data and under 4% for the experimental data compared to reference measurements.
Open AccessTHz-TDS Reflection Measurement of Coating Thicknesses at Non-Perpendicular Incidence: Experiment and Simulation
Time-domain spectroscopy (TDS) in the terahertz (THz) frequency range is gaining in importance in nondestructive testing of dielectric materials. One application is the layer thickness measurement of a coating layer. To determine the thickness from the measurement data, the refractive index of the coating layer must be known in the surveyed frequency range. For perpendicular incidence of the radiation, methods exist to extract the refractive index from the measurement data themselves without prior knowledge. This paper extends these methods for non-perpendicular incidence, where the polarization of the radiation becomes important. Furthermore, modifications considering effects of surface roughness of the coating are introduced. The new methods are verified using measurement data of a sample of Inconel steel coated with yttria-stabilized zirconia (YSZ) and with COMSOL simulations of the measurement setup. To validate the thickness measurements, scanning electron microscopy (SEM) images of the layer structure are used. The results show good agreement with an average error of 1% for the simulation data and under 4% for the experimental data compared to reference measurements.
- Open Access
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 72207-72216
Fully Inkjet-Printed Carbon Nanotube-PDMS-Based Strain Sensor: Temperature Response, Compressive and Tensile Bending Properties, and Fatigue Investigations
Printed and flexible sensors are in the focus of recent efforts to establish the advantages of low-cost manufacturing techniques such as screen printing or inkjet printing for printed electronical applications. Devices based on conductive carbon nanotube (CNT) networks within polymeric matrices such as polydimethylsiloxane (PDMS) are already exceeding mere technological demonstrations. Therefore, we investigate the application-oriented behaviour of fully inkjet-printed CNT/PDMS strain sensors under different conditions such as short- and long-term performance. The sensors exhibit a quasi-linear piezoresistive behaviour with vanishing hysteresis to tensile strain. Significant differences in the resistive response between compressive and tensile strain suggest complex re-orientation mechanisms of CNTs inside the matrix. No clear indication for this phenomenon could be observed in the evolution of the CNT network resistance during fatigue measurements within an uncured or cured PDMS matrix, where both scenarios exhibit no visual degradation. However, these measurements over thousands of cycles show different permanent changes in the overall device resistance exhibiting damages but also recovery in the network. Considering these findings facilitates the development of printed sensor devices.
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 72207-72216
Open AccessFully Inkjet-Printed Carbon Nanotube-PDMS-Based Strain Sensor: Temperature Response, Compressive and Tensile Bending Properties, and Fatigue Investigations
Printed and flexible sensors are in the focus of recent efforts to establish the advantages of low-cost manufacturing techniques such as screen printing or inkjet printing for printed electronical applications. Devices based on conductive carbon nanotube (CNT) networks within polymeric matrices such as polydimethylsiloxane (PDMS) are already exceeding mere technological demonstrations. Therefore, we investigate the application-oriented behaviour of fully inkjet-printed CNT/PDMS strain sensors under different conditions such as short- and long-term performance. The sensors exhibit a quasi-linear piezoresistive behaviour with vanishing hysteresis to tensile strain. Significant differences in the resistive response between compressive and tensile strain suggest complex re-orientation mechanisms of CNTs inside the matrix. No clear indication for this phenomenon could be observed in the evolution of the CNT network resistance during fatigue measurements within an uncured or cured PDMS matrix, where both scenarios exhibit no visual degradation. However, these measurements over thousands of cycles show different permanent changes in the overall device resistance exhibiting damages but also recovery in the network. Considering these findings facilitates the development of printed sensor devices.
- Open Access
- 16 April 2021
- Published by MDPI AG in Preprints.org
THz-TDS Reflection Measurement of Coating Thicknesses at Non-Perpendicular Incidence: Experiment and Simulation
Time-domain spectroscopy (TDS) in the Terahertz (THz) frequency range is gaining in importance in nondestructive testing of dielectric materials. One application is the layer thickness measurement of a coating layer. To determine the thickness from the measurement data, the refractive index of the coating layer must be known in the surveyed frequency range. For perpendicular incidence of the radiation, methods exist to extract the refractive index from the measurement data itself without prior knowledge. This paper extends these methods for non-perpendicular incidence, where the polarization of the radiation becomes important. Furthermore, modifications considering effects of surface roughness of the coating are introduced. The new methods are verified using measurement data of a sample of Inconel steel coated with yttria-stabilized zirconia (YSZ) and with COMSOL simulations of the measurement setup. To validate the thickness measurements, scanning electron microscopy (SEM) images of the layer structure are used. The results show good agreement with an average error of 1% for the simulation data and under 4% for the experimental data compared to reference measurements.
- 16 April 2021
- Published by MDPI AG in Preprints.org
Open AccessTHz-TDS Reflection Measurement of Coating Thicknesses at Non-Perpendicular Incidence: Experiment and Simulation
Time-domain spectroscopy (TDS) in the Terahertz (THz) frequency range is gaining in importance in nondestructive testing of dielectric materials. One application is the layer thickness measurement of a coating layer. To determine the thickness from the measurement data, the refractive index of the coating layer must be known in the surveyed frequency range. For perpendicular incidence of the radiation, methods exist to extract the refractive index from the measurement data itself without prior knowledge. This paper extends these methods for non-perpendicular incidence, where the polarization of the radiation becomes important. Furthermore, modifications considering effects of surface roughness of the coating are introduced. The new methods are verified using measurement data of a sample of Inconel steel coated with yttria-stabilized zirconia (YSZ) and with COMSOL simulations of the measurement setup. To validate the thickness measurements, scanning electron microscopy (SEM) images of the layer structure are used. The results show good agreement with an average error of 1% for the simulation data and under 4% for the experimental data compared to reference measurements.
- Open Access
- 16 November 2020
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 306 (2)
Fiber‐Optic Photoacoustic Generator Realized by Inkjet‐Printing of CNT‐PDMS Composites on Fiber End Faces
In recent years, photoacoustic generators based on multiwalled carbon nanotubes (MWCNT) and polydimethylsiloxane (PDMS) are manufactured in a variety of ways, which influences the properties of the generators with respect to frequency bandwidth, sound wave pressure, robustness, and reproducibility. Due to the high optical absorption of MWCNTs and the high thermal expansion coefficient of PDMS, this combination is ideally suited for use as a photoacoustic generator. This study presents a novel method to produce photoacoustic generators based on long‐term stable MWCNT and PDMS inks with a high reproducibility by means of inkjet‐printing. The MWCNT‐PDMS layers (thicknesses of 2–4 µm), printed directly onto the distal end face of a multimode glass fiber, show a good homogeneity and low optical transmission (19–21%). After the preparation of the fiber pieces, the inkjet printer performs all steps automatically in a time period of 30–60 s per layer. The generated ultrasonic pressure (0.39–0.54 MPa) and frequency bandwidth (1.5–12.7 MHz) can be measured at a distance of ≈4 mm with a laser fluency of 12.7 mJ cm−2. These highly reproducible printed photoacoustic generators can be well used for nondestructive material testing and medical applications.
- 16 November 2020
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 306 (2)
Open AccessFiber‐Optic Photoacoustic Generator Realized by Inkjet‐Printing of CNT‐PDMS Composites on Fiber End Faces
In recent years, photoacoustic generators based on multiwalled carbon nanotubes (MWCNT) and polydimethylsiloxane (PDMS) are manufactured in a variety of ways, which influences the properties of the generators with respect to frequency bandwidth, sound wave pressure, robustness, and reproducibility. Due to the high optical absorption of MWCNTs and the high thermal expansion coefficient of PDMS, this combination is ideally suited for use as a photoacoustic generator. This study presents a novel method to produce photoacoustic generators based on long‐term stable MWCNT and PDMS inks with a high reproducibility by means of inkjet‐printing. The MWCNT‐PDMS layers (thicknesses of 2–4 µm), printed directly onto the distal end face of a multimode glass fiber, show a good homogeneity and low optical transmission (19–21%). After the preparation of the fiber pieces, the inkjet printer performs all steps automatically in a time period of 30–60 s per layer. The generated ultrasonic pressure (0.39–0.54 MPa) and frequency bandwidth (1.5–12.7 MHz) can be measured at a distance of ≈4 mm with a laser fluency of 12.7 mJ cm−2. These highly reproducible printed photoacoustic generators can be well used for nondestructive material testing and medical applications.
- Open Access
- 3 March 2020
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 305 (4)
Synthesis and Characterization of CNT Composites for Laser‐Generated Ultrasonic Waves
In the last few years, extensive progress in ultrasonic wave generation by using multiwalled carbon nanotubes (MWCNTs) in combination with polydimethylsiloxane (PDMS), functional composites, has been achieved. Due to high optical absorption of MWCNTs as perfect absorbers for laser beams and the high thermal expansion coefficient of PDMS, a compact transducer for ultrasonic wave generation at higher frequency can be realized. This study reports a novel method to synthesize MWCNT–PDMS composites deposited on a glass substrate by spray coating, which is done in a short time of 2 h. The layers (0.9–32.2 µm) show low optical transmission properties of 13.9–0.0% at a wavelength of 1047 nm. Apart from using a 1% Triton‐X‐100 stock solution and then diluted to a 0.1% relatively nonhazardous solution, no toxic chemicals are used. The Triton‐X‐100 solution is not hazardous for lab handling and is a commonly used lab detergent for the treatment of biological cells. The achieved sound pressure level is 3.4 MPa with a frequency bandwidth of 9.7 MHz. These results show the potential for a fast and nontoxic production of laser‐generated ultrasonic transducers, which can be used well in the field of nondestructive material testing of layered materials or in medicine with an appropriate frequency range.
- 3 March 2020
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 305 (4)
Open AccessSynthesis and Characterization of CNT Composites for Laser‐Generated Ultrasonic Waves
In the last few years, extensive progress in ultrasonic wave generation by using multiwalled carbon nanotubes (MWCNTs) in combination with polydimethylsiloxane (PDMS), functional composites, has been achieved. Due to high optical absorption of MWCNTs as perfect absorbers for laser beams and the high thermal expansion coefficient of PDMS, a compact transducer for ultrasonic wave generation at higher frequency can be realized. This study reports a novel method to synthesize MWCNT–PDMS composites deposited on a glass substrate by spray coating, which is done in a short time of 2 h. The layers (0.9–32.2 µm) show low optical transmission properties of 13.9–0.0% at a wavelength of 1047 nm. Apart from using a 1% Triton‐X‐100 stock solution and then diluted to a 0.1% relatively nonhazardous solution, no toxic chemicals are used. The Triton‐X‐100 solution is not hazardous for lab handling and is a commonly used lab detergent for the treatment of biological cells. The achieved sound pressure level is 3.4 MPa with a frequency bandwidth of 9.7 MHz. These results show the potential for a fast and nontoxic production of laser‐generated ultrasonic transducers, which can be used well in the field of nondestructive material testing of layered materials or in medicine with an appropriate frequency range.
- 1 November 2019
- Published by Elsevier in Infrared Physics & Technology
- Vol. 102
Application of terahertz time domain spectroscopy for NDT of oxide-oxide ceramic matrix composites
- 1 November 2019
- Published by Elsevier in Infrared Physics & Technology
- Vol. 102
Application of terahertz time domain spectroscopy for NDT of oxide-oxide ceramic matrix composites
- 1 January 2018
- Published by QIRT Council
NDT of Layered Structures Using Pulse-Thermography and THz-TDS Imaging
- 1 January 2018
- Published by QIRT Council
NDT of Layered Structures Using Pulse-Thermography and THz-TDS Imaging
- 10 September 1999
- Published by SPIE-Intl Soc Optical Eng
- Vol. 3827, 16-21
Detection of tightness of mechanical joints using lock-in thermography
Lockin thermography is currently being used for the rapid and remote identification of subsurface structures and defects such as impact damages, delaminations, and hidden corrosion. The purpose of this paper is to show that lockin thermography is also a reliable tool to inspect in a remote way the tightness of mechanical joints in safety relevant structures (e.g. aerospace equipment and vehicles). For example, the rapid identification of loose rivets is a major concern for airlines and manufacturers in order to monitor the structural integrity of their aircraft. Our measurements aimed at the early detection of loose rivets. We analyzed the phase image signature obtained on two metal plates pressed together by screws fastened at various torque levels. A clear relationship was established between phase angle and torque level at which the screws had been fastened. Based on these results our investigations were extended to riveted samples where two aluminum plates were pressed together by an array of ten blind rivets. Also in this case the level of tightness of rivet joints can be detected. In addition to these feasibility studies on model samples, we performed investigations on airplane components which confirmed the applicability of lockin thermography for remote maintenance inspection within a few minutes.© (1999) COPYRIGHT SPIE--The International Society for Optical Engineering. Downloading of the abstract is permitted for personal use only.
- 10 September 1999
- Published by SPIE-Intl Soc Optical Eng
- Vol. 3827, 16-21
Detection of tightness of mechanical joints using lock-in thermography
Lockin thermography is currently being used for the rapid and remote identification of subsurface structures and defects such as impact damages, delaminations, and hidden corrosion. The purpose of this paper is to show that lockin thermography is also a reliable tool to inspect in a remote way the tightness of mechanical joints in safety relevant structures (e.g. aerospace equipment and vehicles). For example, the rapid identification of loose rivets is a major concern for airlines and manufacturers in order to monitor the structural integrity of their aircraft. Our measurements aimed at the early detection of loose rivets. We analyzed the phase image signature obtained on two metal plates pressed together by screws fastened at various torque levels. A clear relationship was established between phase angle and torque level at which the screws had been fastened. Based on these results our investigations were extended to riveted samples where two aluminum plates were pressed together by an array of ten blind rivets. Also in this case the level of tightness of rivet joints can be detected. In addition to these feasibility studies on model samples, we performed investigations on airplane components which confirmed the applicability of lockin thermography for remote maintenance inspection within a few minutes.© (1999) COPYRIGHT SPIE--The International Society for Optical Engineering. Downloading of the abstract is permitted for personal use only.
- 10 September 1999
- Published by SPIE-Intl Soc Optical Eng
- Vol. 3827, 10-15
Ultrasound lock-in thermography: feasibilities and limitations
Conventional thermal wave imaging methods based on optical excitation are sensitive to all thermal boundaries and structures. However, if ultrasound is used for energy deposition, areas of enhanced mechanical loss angle are heated up selectively. As defects are usually correlated with an enhanced loss angle, ultrasound lockin thermography (ULT) is a defect-selective NDE method. Thermal wave emission from defects is monitored that are activated by absorption of ultrasound. In this paper we investigate the applicability of ULT for maintenance and inspection. Examples are presented showing the detection of defects in thick composite materials, of vertical cracks in several materials, and of hidden corrosion. Limitations given by the use of ultrasound are also discussed.
- 10 September 1999
- Published by SPIE-Intl Soc Optical Eng
- Vol. 3827, 10-15
Ultrasound lock-in thermography: feasibilities and limitations
Conventional thermal wave imaging methods based on optical excitation are sensitive to all thermal boundaries and structures. However, if ultrasound is used for energy deposition, areas of enhanced mechanical loss angle are heated up selectively. As defects are usually correlated with an enhanced loss angle, ultrasound lockin thermography (ULT) is a defect-selective NDE method. Thermal wave emission from defects is monitored that are activated by absorption of ultrasound. In this paper we investigate the applicability of ULT for maintenance and inspection. Examples are presented showing the detection of defects in thick composite materials, of vertical cracks in several materials, and of hidden corrosion. Limitations given by the use of ultrasound are also discussed.