Mikel Rincón-Iglesias
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Interests
Mikel Rincón-Iglesias has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Senentxu Lanceros Mendez
BCMaterials, Basque Center for Materials, Applications and Nanostructures, UPV/EHU Science Park, 48940 Leioa, Spain
5 shared publications - Gerardo Hernandez-Sosa
Institute for Automation and Applied Informatics Karlsruhe Institute of Technology Eggenstein‐Leopoldshafen Germany
4 shared publications - Peter Krebsbach
Light Technology Institute Karlsruhe Institute of Technology Engesserstr. 13 76131 Karlsruhe Germany
3 shared publications - Cristian Mendes-Felipe
Basque Center for Materials, Applications and Nanostructures UPV/EHU Science Park Leioa Spain
2 shared publications - Ander García Díez
BCMaterials, Basque Center for Materials, Applications and Nanostructures, UPV/EHU Science Park, 48940 Leioa, Spain
1 shared publication - Carlos Miguel Costa
Physics Centre of Minho and Porto Universities (CF-UM-UP), University of Minho, Campus de Gualtar, 4710-057 Braga, Portugal
1 shared publication
Latest Publications
- Open Access
- 4 November 2026
- Published by Wiley in Advanced Functional Materials
Digitally Printed Eco‐Friendly Electronic Devices
The sustainable life cycle of electronics is one of the major challenges of modern society. Moreover, the manufacturing of conventional electronics significantly impacts the environment due to the extensive consumption of raw materials, energy, and the release of harmful byproducts. In this regard, manufacturing of electronics using eco‐friendly materials through digital printing routes represents a promising and sustainable solution. This review discusses the state‐of‐the‐art research in this field, exploring various digital printing techniques such as inkjet, electro–hydro–dynamic jet, aerosol‐jet, and extrusion printing techniques, focusing on resource efficient manufacturing with minimal material wastage and their environmental impacts. Various eco‐friendly ink formulation strategies are discussed together with their practical application. Additionally, the review addresses various end‐of‐life management strategies such as repair, recycling, and biodegradation. Finally, major challenges associated with digital printing of eco‐friendly electronics to compete with conventional electronics are explored and future perspectives in this emerging area are outlined.
- 4 November 2026
- Published by Wiley in Advanced Functional Materials
Open AccessDigitally Printed Eco‐Friendly Electronic Devices
The sustainable life cycle of electronics is one of the major challenges of modern society. Moreover, the manufacturing of conventional electronics significantly impacts the environment due to the extensive consumption of raw materials, energy, and the release of harmful byproducts. In this regard, manufacturing of electronics using eco‐friendly materials through digital printing routes represents a promising and sustainable solution. This review discusses the state‐of‐the‐art research in this field, exploring various digital printing techniques such as inkjet, electro–hydro–dynamic jet, aerosol‐jet, and extrusion printing techniques, focusing on resource efficient manufacturing with minimal material wastage and their environmental impacts. Various eco‐friendly ink formulation strategies are discussed together with their practical application. Additionally, the review addresses various end‐of‐life management strategies such as repair, recycling, and biodegradation. Finally, major challenges associated with digital printing of eco‐friendly electronics to compete with conventional electronics are explored and future perspectives in this emerging area are outlined.
- Open Access
- 25 May 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (22) , 32680-32690
Sustainable Fully Inkjet-Printed Humidity Sensor Based on Ionic Liquid and Hydroxypropyl Cellulose
The increasing number of sensors contributing to the Internet of Things (IoT) aggravates the e-waste generated globally. Thus, it is an urgent necessity to develop more sustainable sensors. This paper presents a fully inkjet-printed dual-response (electrical and visual) humidity sensor based on hydroxypropyl cellulose (HPC) and the ionic liquid bis(1-butyl-3-methylimidazolium) tetrachloronickelate ([Bmim]2[NiCl4]). The active layer was printed on interdigitated silver electrodes on a flexible cellulose acetate substrate. The optimized ink includes HPC, [Bmim]2[NiCl4], ethylene glycol, water, and Tergitol. HPC and the IL exhibit excellent compatibility, forming homogeneous films without phase separation even at high IL concentration. The printed sensor for an IL content of 50 wt % demonstrates a proportional response when varying the relative humidity (RH) from 30 to 90 RH%, with a high sensitivity of 163, comparable to that of a commercial reference sensor, a low hysteresis of 1.5 RH%, and a fast response time of 0.8 s. In addition, a visual response from colorless to cyan is observed upon dehydration. This color change is visible to the naked eye for a relative humidity below 30 RH% when a transmittance lower than 93% is obtained in the visible spectra. This dual-response humidity sensor, fabricated from sustainable materials and low-cost printing technology, has great potential for a variety of applications, including environmental monitoring, smart agriculture, fire safety, and quality control in the food industry.
- 25 May 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (22) , 32680-32690
Open AccessSustainable Fully Inkjet-Printed Humidity Sensor Based on Ionic Liquid and Hydroxypropyl Cellulose
The increasing number of sensors contributing to the Internet of Things (IoT) aggravates the e-waste generated globally. Thus, it is an urgent necessity to develop more sustainable sensors. This paper presents a fully inkjet-printed dual-response (electrical and visual) humidity sensor based on hydroxypropyl cellulose (HPC) and the ionic liquid bis(1-butyl-3-methylimidazolium) tetrachloronickelate ([Bmim]2[NiCl4]). The active layer was printed on interdigitated silver electrodes on a flexible cellulose acetate substrate. The optimized ink includes HPC, [Bmim]2[NiCl4], ethylene glycol, water, and Tergitol. HPC and the IL exhibit excellent compatibility, forming homogeneous films without phase separation even at high IL concentration. The printed sensor for an IL content of 50 wt % demonstrates a proportional response when varying the relative humidity (RH) from 30 to 90 RH%, with a high sensitivity of 163, comparable to that of a commercial reference sensor, a low hysteresis of 1.5 RH%, and a fast response time of 0.8 s. In addition, a visual response from colorless to cyan is observed upon dehydration. This color change is visible to the naked eye for a relative humidity below 30 RH% when a transmittance lower than 93% is obtained in the visible spectra. This dual-response humidity sensor, fabricated from sustainable materials and low-cost printing technology, has great potential for a variety of applications, including environmental monitoring, smart agriculture, fire safety, and quality control in the food industry.
- 23 May 2025
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 7 (11) , 5106-5114
Local Magnetoelectric Effect in All-Printed Magnetorheological Elastomer-Piezoelectric Polymer Layered Structures
- 23 May 2025
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 7 (11) , 5106-5114
Local Magnetoelectric Effect in All-Printed Magnetorheological Elastomer-Piezoelectric Polymer Layered Structures
- Open Access
- 1 August 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (32) , 42555-42565
Inkjet-Printed Bio-Based Melanin Composite Humidity Sensor for Sustainable Electronics
A lack of sustainability in the design of electronic components contributes to the current challenges of electronic waste and material sourcing. Common materials for electronics are prone to environmental, economic, and ethical problems in their sourcing, and at the end of their life often contribute to toxic and nonrecyclable waste. This study investigates the inkjet printing of flexible humidity sensors and includes biosourced and biodegradable materials to improve the sustainability of the process. Humidity sensors are useful tools for monitoring atmospheric conditions in various fields. Here, an aqueous dispersion of black soldier fly melanin was optimized for printing with a cosolvent and deposited onto interdigitated silver electrodes on flexible substrates. Impedance spectroscopy demonstrated that adding choline chloride increased the ion concentration and AC conductivity by more than 3 orders of magnitude, resulting in a significant improvement in sensing performance and reduced hysteresis. The devices exhibit fast detection (0.8 ± 0.5 s) and recovery times (0.8 ± 0.3 s), with a 170 ± 40-fold decrease in impedance for relative humidity changes from 30% to 90%. This factor is lowered upon prolonged exposure to high humidity in tests over 72 h during which a stable operation is reached. The low embodied energy of the sensor, achieved through material-efficient deposition and the use of waste management byproducts, enhances its sustainability. In addition, approaches for reusability and degradability are presented, rendering the sensor suitable for wearable or agricultural applications.
- 1 August 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (32) , 42555-42565
Open AccessInkjet-Printed Bio-Based Melanin Composite Humidity Sensor for Sustainable Electronics
A lack of sustainability in the design of electronic components contributes to the current challenges of electronic waste and material sourcing. Common materials for electronics are prone to environmental, economic, and ethical problems in their sourcing, and at the end of their life often contribute to toxic and nonrecyclable waste. This study investigates the inkjet printing of flexible humidity sensors and includes biosourced and biodegradable materials to improve the sustainability of the process. Humidity sensors are useful tools for monitoring atmospheric conditions in various fields. Here, an aqueous dispersion of black soldier fly melanin was optimized for printing with a cosolvent and deposited onto interdigitated silver electrodes on flexible substrates. Impedance spectroscopy demonstrated that adding choline chloride increased the ion concentration and AC conductivity by more than 3 orders of magnitude, resulting in a significant improvement in sensing performance and reduced hysteresis. The devices exhibit fast detection (0.8 ± 0.5 s) and recovery times (0.8 ± 0.3 s), with a 170 ± 40-fold decrease in impedance for relative humidity changes from 30% to 90%. This factor is lowered upon prolonged exposure to high humidity in tests over 72 h during which a stable operation is reached. The low embodied energy of the sensor, achieved through material-efficient deposition and the use of waste management byproducts, enhances its sustainability. In addition, approaches for reusability and degradability are presented, rendering the sensor suitable for wearable or agricultural applications.
- 24 February 2020
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 2 (4) , 1448-1457
Tailoring Electrical and Mechanical Properties of All-Natural Polymer Composites for Environmentally Friendlier Electronics
- 24 February 2020
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 2 (4) , 1448-1457
Tailoring Electrical and Mechanical Properties of All-Natural Polymer Composites for Environmentally Friendlier Electronics