Ponnam Anjaneyulu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ponnam Anjaneyulu has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- C. S. Suchand Sangeeth
Department of Physics National Institute of Technology Calicut Kerala India
6 shared publications Reghu Menon
6 shared publicationsVaibhav Varade
6 shared publicationsK. P. Ramesh
Indian Institute of Science 1 Department of Physics Bangalore 560012, India
3 shared publicationsR. Menon
Department of Physics, Indian Institute of Science, Bangalore-560012, India
3 shared publications- Amit Roy
Department of Physics, School of Advanced Sciences (SAS)
2 shared publications
Latest Publications
- 17 May 2026
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (10)
Coexistence of Nonvolatile and Volatile Memory in Molybdenum Disulfide‐Polymethyl Methacrylate Polymer Nanocomposite Memory Device
A two‐terminal RRAM device based on a poly methyl‐methacrylate (PMMA) and molybdenum disulfide (MoS 2 ) polymer nanocomposite is studied in this work. The structure and bandgap of MoS 2 nanoparticles are investigated using material characterization methods, such as XRD and UV‐Vis DRS. The Silver (Ag) and fluorine‐doped tin oxide (FTO) glass are used as the top and bottom electrodes, in the fabrication of the polymer nanocomposite device. The device FTO/MoS 2 ‐PMMA/Ag exhibits both volatile and nonvolatile resistive switching, with the switching behavior primarily dependent on the voltage‐sweep polarity, according to systematic current–voltage ( I – V ) measurements. The nonvolatile resistive‐switching properties demonstrate write‐once‐read‐many (WORM) memory. The device's reliability is demonstrated through stability tests, including retention and endurance tests. I – V data analysis indicates the impact of the conduction mechanism on the nonvolatility and volatility of the device memory, thereby aiding in understanding the switching behaviour. The coexistence of volatile and nonvolatile resistive switching memory in the device is understood by modeling the I – V data using various bulk‐limited and electrode‐limited conduction mechanisms.
- 17 May 2026
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (10)
Coexistence of Nonvolatile and Volatile Memory in Molybdenum Disulfide‐Polymethyl Methacrylate Polymer Nanocomposite Memory Device
A two‐terminal RRAM device based on a poly methyl‐methacrylate (PMMA) and molybdenum disulfide (MoS 2 ) polymer nanocomposite is studied in this work. The structure and bandgap of MoS 2 nanoparticles are investigated using material characterization methods, such as XRD and UV‐Vis DRS. The Silver (Ag) and fluorine‐doped tin oxide (FTO) glass are used as the top and bottom electrodes, in the fabrication of the polymer nanocomposite device. The device FTO/MoS 2 ‐PMMA/Ag exhibits both volatile and nonvolatile resistive switching, with the switching behavior primarily dependent on the voltage‐sweep polarity, according to systematic current–voltage ( I – V ) measurements. The nonvolatile resistive‐switching properties demonstrate write‐once‐read‐many (WORM) memory. The device's reliability is demonstrated through stability tests, including retention and endurance tests. I – V data analysis indicates the impact of the conduction mechanism on the nonvolatility and volatility of the device memory, thereby aiding in understanding the switching behaviour. The coexistence of volatile and nonvolatile resistive switching memory in the device is understood by modeling the I – V data using various bulk‐limited and electrode‐limited conduction mechanisms.
- 7 April 2026
- Published by Elsevier in Synthetic Metals
- Vol. 319
Chromium cyanurate-based robust resistive switching device emulating synaptic plasticity for neuromorphic application
- 7 April 2026
- Published by Elsevier in Synthetic Metals
- Vol. 319
Chromium cyanurate-based robust resistive switching device emulating synaptic plasticity for neuromorphic application
- 11 December 2025
- Published by Elsevier in Synthetic Metals
- Vol. 317
Influence of quinoid and aromatic structures on the electrical properties of electropolymerized poly(3-methylthiophene) devices
- 11 December 2025
- Published by Elsevier in Synthetic Metals
- Vol. 317
Influence of quinoid and aromatic structures on the electrical properties of electropolymerized poly(3-methylthiophene) devices
- 20 May 2023
- Published by Elsevier in Current Applied Physics
- Vol. 52, 57-64
Tailoring opto-electronic and interface properties via electrochemical doping in Poly(3-hexylthiophene)
- 20 May 2023
- Published by Elsevier in Current Applied Physics
- Vol. 52, 57-64
Tailoring opto-electronic and interface properties via electrochemical doping in Poly(3-hexylthiophene)
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2548 (1) , 030014
A comparative study on TiO2 nanoparticle and TiO2 nanosheets for resistive random accesses memory (RRAM) applications
The 3D TiO2 nanoparticles and 2D TiO2 nanosheets solutions were spin-coated on FTO substrates. A comparative resistive switching study was carried out by DC and AC measurements. The investigations revealed that the resistive switching ratio is enhanced when TiO2 nanoparticles were replaced by TiO2 nanosheets as an active layer. TiO2 nanoparticles exhibited one order of WORM type resistive switching. Whereas, TiO2 nanosheets exhibited two orders of Bipolar resistive switching behaviour. Both devices had data retention of ∼1 hour making them the effective device for non-volatile memory applications.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2548 (1) , 030014
Open AccessA comparative study on TiO2 nanoparticle and TiO2 nanosheets for resistive random accesses memory (RRAM) applications
The 3D TiO2 nanoparticles and 2D TiO2 nanosheets solutions were spin-coated on FTO substrates. A comparative resistive switching study was carried out by DC and AC measurements. The investigations revealed that the resistive switching ratio is enhanced when TiO2 nanoparticles were replaced by TiO2 nanosheets as an active layer. TiO2 nanoparticles exhibited one order of WORM type resistive switching. Whereas, TiO2 nanosheets exhibited two orders of Bipolar resistive switching behaviour. Both devices had data retention of ∼1 hour making them the effective device for non-volatile memory applications.
- 1 May 2021
- Published by Elsevier in Current Applied Physics
- Vol. 25, 75-81
Role of sweep direction and substrate work function on resistive switching of titanium-di-oxide [TiO2] nanoparticles
- 1 May 2021
- Published by Elsevier in Current Applied Physics
- Vol. 25, 75-81
Role of sweep direction and substrate work function on resistive switching of titanium-di-oxide [TiO2] nanoparticles
- 1 December 2020
- Published by Elsevier in Synthetic Metals
- Vol. 270
Synthesis and electrical properties of polyaniline–cerium oxide composites
- 1 December 2020
- Published by Elsevier in Synthetic Metals
- Vol. 270
Synthesis and electrical properties of polyaniline–cerium oxide composites
- 19 May 2020
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 53 (29) , 295301
Anomalous current–voltage and impedance behaviour in doped Poly 3-methylthiophene devices
Current–voltage (I–V) and impedance measurements are performed on electrochemically-doped poly(3-methylthiophene) (P3MeT) devices in metal/polymer/metal sandwich geometry. The detailed investigation shows the presence of negative differential resistance (NDR) in the sandwich devices with different metals in action as substrate and top electrode. It is found that the reiteration of I–V measurements significantly enhances the NDR. The P3MeT devices shows a considerable switching behaviour with ON to OFF ratio varying between two to three order but lacks the consistency in bias stress test. An anomalous behaviour in the impedance measurements in the form of a prolonged tail is observed in Cole–Cole plots towards lower frequency region, which gets more prominent with applied bias. This impedance anomaly is explained in terms of large distribution of relaxation times arising due to long lived trap states at the bulk and interface which is correlated with the NDR observed in P3MeT devices.
- 19 May 2020
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 53 (29) , 295301
Anomalous current–voltage and impedance behaviour in doped Poly 3-methylthiophene devices
Current–voltage (I–V) and impedance measurements are performed on electrochemically-doped poly(3-methylthiophene) (P3MeT) devices in metal/polymer/metal sandwich geometry. The detailed investigation shows the presence of negative differential resistance (NDR) in the sandwich devices with different metals in action as substrate and top electrode. It is found that the reiteration of I–V measurements significantly enhances the NDR. The P3MeT devices shows a considerable switching behaviour with ON to OFF ratio varying between two to three order but lacks the consistency in bias stress test. An anomalous behaviour in the impedance measurements in the form of a prolonged tail is observed in Cole–Cole plots towards lower frequency region, which gets more prominent with applied bias. This impedance anomaly is explained in terms of large distribution of relaxation times arising due to long lived trap states at the bulk and interface which is correlated with the NDR observed in P3MeT devices.
- 27 October 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 122 (16)
Charge transport mechanism in p-type copper ion containing triazine thiolate metallopolymer thin film devices
The charge transport mechanism in copper ions containing 1,3,5-Triazine-2,4,6-trithiolate (CuTCA) based polymer device in sandwich (Ag/CuTCA/Cu) geometry is studied. The current-voltage (I-V) characteristics of the metallopolymer CuTCA device have shown a transition in the charge transport mechanism from Ohmic to Space-charge limited conduction when temperature and voltage are varied. The carriers in CuTCA devices exhibit hopping transport, in which carriers hop from one site to the other. The hole mobility in this polymer device is found to be dependent on electric field E ( ) and temperature, which suggests that the polymer has inherent disorder. The electric-field coefficient γ and zero-field mobility μ0 are temperature dependent. The values of mobility and activation energies are estimated from temperature (90–140 K) dependent charge transport studies and found to be in the range of 1 × 10−11–8 × 10−12 m2/(V s) and 16.5 meV, respectively. Temperature dependent electric-field coefficient γ is in the order of 17.8 × 10−4 (m/V)1/2, and the value of zero-field mobility μ0 is in the order of 1.2 × 10−11 m2/(V s) at 140 K. A constant phase element (Q) is used to model the device parameters, which are extracted using the Impedance spectroscopy technique. The bandgap of the polymer is estimated to be 2.6 eV from UV-Vis reflectance spectra.- 27 October 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 122 (16)
Charge transport mechanism in p-type copper ion containing triazine thiolate metallopolymer thin film devices
The charge transport mechanism in copper ions containing 1,3,5-Triazine-2,4,6-trithiolate (CuTCA) based polymer device in sandwich (Ag/CuTCA/Cu) geometry is studied. The current-voltage (I-V) characteristics of the metallopolymer CuTCA device have shown a transition in the charge transport mechanism from Ohmic to Space-charge limited conduction when temperature and voltage are varied. The carriers in CuTCA devices exhibit hopping transport, in which carriers hop from one site to the other. The hole mobility in this polymer device is found to be dependent on electric field E ( ) and temperature, which suggests that the polymer has inherent disorder. The electric-field coefficient γ and zero-field mobility μ0 are temperature dependent. The values of mobility and activation energies are estimated from temperature (90–140 K) dependent charge transport studies and found to be in the range of 1 × 10−11–8 × 10−12 m2/(V s) and 16.5 meV, respectively. Temperature dependent electric-field coefficient γ is in the order of 17.8 × 10−4 (m/V)1/2, and the value of zero-field mobility μ0 is in the order of 1.2 × 10−11 m2/(V s) at 140 K. A constant phase element (Q) is used to model the device parameters, which are extracted using the Impedance spectroscopy technique. The bandgap of the polymer is estimated to be 2.6 eV from UV-Vis reflectance spectra.- 1 February 2017
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 50 (9) , 095103
Investigation of disorder and its effect on electrical transport in electrochemically doped polymer devices by current–voltage and impedance spectroscopy
We report on the analysis of temperature-dependent current–voltage characteristics and impedance measurements of electrochemically doped poly(3-methylthiophene) devices at different doping levels. The extent of doping is carefully tailored such that only the bulk-limited transport mechanism prevails. A transition from exponentially distributed trap-limited transport to trap-free space-charge-limited current is observed in current–voltage conduction upon increasing the doping. The obtained trap densities (3.2 × 10 16 cm −3 and 8.6 × 10 15 cm −3 ) and trap energies (31.7 meV and 16.6 meV) for different devices signify the variation in disorder with doping, which is later supported by impedance measurements. Impedance–frequency data for various devices can not be explained using the parallel resistance–capacitance ( RC ) model in the equivalent circuit. However, this was established by incorporating a constant phase element Q (CPE) instead of the capacitance parameter. It should be emphasized that low doping devices in particular are best simulated with two CPE elements, while the data related to other devices are fitted well with a single CPE element. It is also observed from evaluated circuit parameters that the spatial inhomogeneity and disorder are the cause of variability in different samples, which has an excellent correlation with the temperature-dependent current–voltage characteristics.
- 1 February 2017
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 50 (9) , 095103
Investigation of disorder and its effect on electrical transport in electrochemically doped polymer devices by current–voltage and impedance spectroscopy
We report on the analysis of temperature-dependent current–voltage characteristics and impedance measurements of electrochemically doped poly(3-methylthiophene) devices at different doping levels. The extent of doping is carefully tailored such that only the bulk-limited transport mechanism prevails. A transition from exponentially distributed trap-limited transport to trap-free space-charge-limited current is observed in current–voltage conduction upon increasing the doping. The obtained trap densities (3.2 × 10 16 cm −3 and 8.6 × 10 15 cm −3 ) and trap energies (31.7 meV and 16.6 meV) for different devices signify the variation in disorder with doping, which is later supported by impedance measurements. Impedance–frequency data for various devices can not be explained using the parallel resistance–capacitance ( RC ) model in the equivalent circuit. However, this was established by incorporating a constant phase element Q (CPE) instead of the capacitance parameter. It should be emphasized that low doping devices in particular are best simulated with two CPE elements, while the data related to other devices are fitted well with a single CPE element. It is also observed from evaluated circuit parameters that the spatial inhomogeneity and disorder are the cause of variability in different samples, which has an excellent correlation with the temperature-dependent current–voltage characteristics.