STSerhii Terekhov

Serhii Terekhov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Serhii Terekhov has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Use of 3D Printers for the Manufacture of Complex Multi-Component Dentures in Dentistry

    by Maryan Domysche, Serhii Terekhov, Olena Astapenko, Stanislav Vefelev, Olha Tatarina

    Introduction: Three-dimensional (3D) printing has transformed dentistry by enhancing precision, efficiency, and reducing material waste in prosthesis manufacturing. The objective of this study is to evaluates (3D) printing effectiveness and operational parameters by assessing technology used, workflow efficiency, patient outcomes and complications in dental procedures, focusing on its clinical applicability and impact on patient care. Methods: A systematic literature review was done for articles from 2015 to 2024. A systematic search of multiple databases, including PubMed and Google Scholar, yielded 3785 studies, which were narrowed to 15 studies that focused on 3D printing technology in multi-part dental prostheses. Results: The 3D-printed material was compared with conventional rapid prototyping material, and good strength characteristics of the prostheses were achieved. 3D-printed prostheses' long-term performance depends on constantly developing techniques and technologies. 3D-printed prosthesis accuracy was relatively high, but patient throughput, complexity, and limited precision needed to be more satisfactory. Literature reviews, randomized controlled trials, single-centre clinical trials, and in vitro and observational studies were also included in this study. Conclusions: Although limitations about material properties, production costs, and accuracy still exist, the prospects of 3D printing for clinical application in dental prosthetics are very encouraging. Enhanced digital workflows have positively impacted patient engagement, yet additional research is needed to improve such practices in the clinic for maximal patient satisfaction


  • Open Access

    GINGIVAL MARGIN, CORRECTION IN ORTHOPEDIC DENTISTRY

    by S. S. Terekhov, A. M. Proshchenko

    A big problem for obtaining aesthetic and functional results of dental treatment is the condition of the gingival papillae. The effectiveness of orthopedic interventions without high-quality correction of the marginal edge of the gums can lead to an unsatisfactory result and the occurrence of numerous complications Materials and methods. A literature search was conducted in the PubMed and Medline databases for the period 2000-2024, for which the following keywords were used: correction of soft gingival tissues, fixed dentures, effectiveness, front group of teeth. A general search revealed 112 sources regarding gingival margin correction in fixed dentures. The primary exclusion referred to literary sources in which the correction of the gingival margin applied to all types of prosthetics. Literary sources that contained only reference information were included in the secondary exclusion. As a result, only relevant full-text articles in professional journals remained (n=25). The purpose of the research is to analyze the methods of gingival margin correction in orthopedic dentistry at the current stage, to formulate relevant tasks for further research. Research results. Methods of restoration of the aesthetics of the marginal part of the gums during orthopedic treatment are divided into the following groups: plastic of soft and bone tissues; laboratory and technical procedures; use of materials for artificial gums. It has been established that the plastic-surgical method is used for the loss of the gingival papilla, defects of the ridge of the alveolar process, asymmetric contour of the gums, and their unaesthetic shape. Correction of the gums allows to achieve satisfactory aesthetic results both at the final stage of orthopedic treatment (prosthetics with fixed orthopedic prostheses) and at the intermediate stage of temporary prosthetics with plastic fixed prostheses. It was found that the most common methods of gingival margin correction are flap operations on the gums using the technique of lateral movement of the muco-osseous flap. These include the following types of interventions: endothelial modification from the tooth-alveolar ridge; oblique displaced flap; periosteally stimulated flap; partial or complete split flap. The positive effect of hyaluronic acid on the healing of the gingival margin and tissue regeneration has been proven. Several researches have shown the positive effects of hyaluronic acid on gingival margin healing and tissue regeneration due to its properties to stimulate cell adhesion, migration and proliferation, mediate cell signaling. The authors indicate a better effectiveness of hyaluronic acid in relation to periodontal parameters during the correction of the marginal gingival margin. The use of a laser scalpel is characterized by less pronounced traumatization of tissues, lower temporary costs for intervention, reduced blood loss, less pronounced signs of inflammation in the postoperative period, relative simplicity and cost-effectiveness of use. Conclusions. To date, only a combination of various orthopedic and surgical manipulations allows to achieve an optimal aesthetic result during prosthetics with fixed dentures of the front group of teeth.


  • Open Access

    DIRECT AND LONG-TERM RESULTS OF USING LASER GUM CORRECTION IN ORTHOPEDIC DENTISTRY

    by V.P. Nespriadko, S.S. Terekhov

    Мета дослідження – здійснити аналіз результатів застосування лазерної корекції ясен в ортопедичній стоматології за динамікою больового синдрому, глибиною зубоясенної борозенки. Матеріал та методи. У роботу включені дані 100 пацієнтів: 46,0 % чоловіків та 54,0 % жінок віком від 30 до 74 років, середній вік – 57,3±15,1 років. Для оцінки вираженості больового синдрому використовували візуальну аналогову шкалу. Вимірювання глибини зубоясенної борозенки проводили градуйованим пародонтологічним зондом. Клінічний стан тканин крайового пародонту визначали за допомогою ясенного індексу. Результати. Доведено, що внаслідок застосування лазерної корекції больовий синдром виникає лише у 2,8 % пацієнтів проти 23,5 % у групі діатермічної корекції ясенного краю. Тобто «шанси» (OR – odds ratio) больового синдрому при лазерній корекції зменшувались у 10,0 разів (р = 0.023). Встановлено меншу інтенсивність больового синдрому в групі лазерної корекції порівняно з діатермічною (p<0,05). Верифіковано, що більші показники ясенного індексу спостерігали у групі лазерної корекції проти діатермічної (p<0,05) (через 1 місяць спостереження). Доведено, що менше проникнення в ясенну борозну виявлено при отриманні відбитка після виконання корекції діатермічним способом (50,8±6,23 %), що поступалося глибині проникнення матеріалу після корекції лазером (64,7±4,2 %), р<0,05. Висновки. Дослідження відображає ефективність лазерної корекції із застосуванням апарату Lika Surgeon при оцінці безпосередніх та віддалених результатів ортодонтичного лікування пацієнтів. Вираженість больового синдрому в ранньому періоді є меншою, а глибина проникнення борозни – більшою, ніж при застосуванні лазерної корекції.

  • Open Access

    Efficiency of photoactivated implant surface processing method for increasing stability of dental implant

    by S. Terekhov, A. Proshchenko, N. Proshchenko

    Stability of the implants is based on its endurance, which is very important for further decision and prognosis. For creation of hydrophilic surface were instilled the different methods of treatment. At the same time, the efficiency of photoactivation method and its perspectives for the increasing of the implant stability is not yet enough researched and needs the special attention. The aim of the study is to assess the stability of two groups of implants, evaluated either by the grit blasting processing and acid etching alone, or with additional photoactivation, using resonance frequency analysis (RFA). 101 implants of 56 patients (20 men and 36 women) were studied, 53 of them were treated with grit blasting processing and acid etching, and 48 with photo activation. The Implant stability quality (ISQ) was measured using the RFA method on the day of the implant set, and after 2, 8 and 16 weeks for each implant. For statistical analysis was used software package Statistica 10.0 for Windows, with following calculating M (arithmetic mean) and m (error of the arithmetic mean). Differences at p<0.05 were signed considered probable. After 8 weeks, higher indices of the stability of the implant were established in the group where photoactivation was applied (for 4,1 points ISQ, p<0,05). After 16 weeks, the implant stability quality factor was likely to be higher after the photoactivated surface of the implant (3,9 points ISQ, p<0,05). When comparing the stability ratio of the upper-jaw and lower-jaw implants in each group, both groups showed a higher coefficient of stability of the implant for the lower jaw than for the upper-jaw implants at each stage of observation (p<0,05). The average ISQ value was higher in implants with super hydrophilic surface, treated with a photocatalytic effect than in those, who did not receive such treatment, i.e. photoactivation of the surface of the implant promotes osteointegration by increasing the hydrophilic surface. Keywords: implant's stability, implant stability quality, photoactivation, resonance-frequency analysis.

  • Open Access

    GUM RETRACTION METHODS IN ORTHOPEDIC DENTISTRY: CURRENT STATE OF THE PROBLEM

    by V. P. Nespriadko, S. S. Terekhov

    Gingival retraction is the procedure of bending the gingival margin away from the tooth surface, which provides sufficient horizontal and vertical space between the prepared finish line and the gingiva for the introduction of a sufficient amount of impression material. Several factors influence the success and durability of orthopedic restorations in dentistry. In particular, supragingival margins are necessary to maintain periodontal health, but do not provide optimal aesthetics. The gingival margin should be clean and accessible during impression making, and the gingival groove should be wide enough (from 0.15 to 0.20 mm). Therefore, in orthopedic dentistry, the problem of the optimal gum retraction technique, the influence of the chosen technique on the impression procedure is relevant. Ideally, the gum retraction technique should be simple, fast and inexpensive, should not cause damage to the periodontal tissues. Today, there are various methods of retraction, including retraction cords, rotary curettage, copper tapes, electrosurgical techniques, laser retraction, and the use of some types of polymer and plastic materials. The article provides an overview of the main commonly accepted methods of gum retraction, which can be classified into mechanical, chemical and surgical. Particular attention is paid to such retraction methods as non-medicated cords, medicated cords, wireless methods, astringent hemostatic agents, retraction paste for gums, vasoconstrictors, lasers, rotary curettage, electrosurgery. Study substantiation: Despite significant progress of orthopedic dentistry in the last decades, clear criteria for selection of method of retraction are not currently allocated. The purpose of the study: to conduct an analysis of modern and available methods of gum retraction in orthopedic dentistry, to highlight the safety and effectiveness criteria of each of the methods, depending on the clinical situation. The materials and methods: the available scientific sources of recent years, devoted to the technique of gum retraction in orthopedic dentistry, analyzed by the methods of review, system and content analysis. The search strategy was to manually search the Pub-Med and Google Scholar databases from 1985 to 2022 for articles related to retraction prior to making an impression of a fixed prosthesis. Key words included "impression making" and "gingival retraction". The clinical effectiveness of retraction methods is assessed according to the following criteria: A – effectiveness (degree of horizontal and vertical gum recession, possibility of controlling bleeding and outflow of gum fluid). B – degree of retraction (ideally, the agents used should not lead to damage to the epithelial tissue). Otherwise, this damage should be reversible. The maximum apical recession after gingival retraction should not exceed 0.10 mm. C-absorption of retraction agents in tissue should not cause systemic effects. The conclusion of the review is a general assessment of the effectiveness of retraction methods according to the following criteria: effectiveness, degree of retraction, absorption of retraction agents. Emphasis is placed on the greatest efficiency of the laser retraction method. The author suggests further research in this direction. Despite the significant progress of orthopedic dentistry in recent decades, additional research should be conducted to develop clear criteria for the effectiveness of gum retraction methods. Gingival retraction is the procedure of bending the gingival margin away from the tooth surface, which provides sufficient horizontal and vertical space between the prepared finish line and the gingiva for the introduction of a sufficient amount of impression material. Several factors influence the success and durability of orthopedic restorations in dentistry. In particular, supragingival margins are necessary to maintain periodontal health, but do not provide optimal aesthetics. The gingival margin should be clean and accessible during impression making, and the gingival groove should be wide enough (from 0.15 to 0.20 mm). Therefore, in orthopedic dentistry, the problem of the optimal gum retraction technique, the influence of the chosen technique on the impression procedure is relevant. Ideally, the gum retraction technique should be simple, fast and inexpensive, should not cause damage to the periodontal tissues. Today, there are various methods of retraction, including retraction cords, rotary curettage, copper tapes, electrosurgical techniques, laser retraction, and the use of some types of polymer and plastic materials. The article provides an overview of the main commonly accepted methods of gum retraction, which can be classified into mechanical, chemical and surgical. Particular attention is paid to such retraction methods as non-medicated cords, medicated cords, wireless methods, astringent hemostatic agents, retraction paste for gums, vasoconstrictors, lasers, rotary curettage, electrosurgery. Study substantiation: Despite significant progress of orthopedic dentistry in the last decades, clear criteria for selection of method of retraction are not currently allocated. The purpose of the study: to conduct an analysis of modern and available methods of gum retraction in orthopedic dentistry, to highlight the safety and effectiveness criteria of each of the methods, depending on the clinical situation. The materials and methods: the available scientific sources of recent years, devoted to the technique of gum retraction in orthopedic dentistry, analyzed by the methods of review, system and content analysis. The search strategy was to manually search the Pub-Med and Google Scholar databases from 1985 to 2022 for articles related to retraction prior to making an impression of a fixed prosthesis. Key words included "impression making" and "gingival retraction". The clinical effectiveness of retraction methods is assessed according to the following...

  • Open Access

    Вплив ретракції на мікроциркуляторне русло у тканинах крайового пародонта перед отриманням відбитка для незнімних конструкцій

    by В.п. Неспрядько, S.S. Terekhov

    The article discusses the effect of the retraction procedure on the microvasculature in the tissues of the regional periodontium in patients with various gum biotypes. The relationship between the strength of the traumatic agent during gum retraction and the phenotype of marginal periodontium is noted. Not only because of the orthopedic design, the condition of the marginal gum worsens. Due to the dense tension and gum retraction, blood circulation in the bloodstream also decreases, and the quality of orthopedic treatment is also reduced. The most pronounced effect was felt by patients with a thin gum biotype, which is associated with damage to the epithelial attachment during retraction. В статье рассматривается влияние ретракции десен на микроциркуляторное русло в тканях пародонта у пациентов с различными биотипами десен. Отмечается взаимосвязь между силой травмирующего агента при ретракции десны и фенотипом краевого пародонта. У статті розглядається вплив ретракції на мікроциркуляторне русло у тканинах крайового пародонта в пацієнтів із різними біотипами ясен. Відмічається взаємозв’язок між силою травмуючого агента під час ретракції ясен і фенотипом крайового пародонта.


  • DIGITAL VOLUME SCANNING SYSTEM FOR IMPROVING THE QUALITY OF GARDEN RETRACTION

    by S.S. Terekhov, N.S. Khrol

    Digital 3D scanning technology of the CAD / CAM system was used to increase the accuracy of the stump depth of the examined teeth. Collapsible plaster models were made for each clinical case and scanned in the CAD system - digital volume scanner. Using this technology on a 3D model to determine the exact depth of preparation of the stump. It was found that the study by digital volume scanning to determine and verify the depth of preparation of the examined teeth by orthopaedists, allows a more accurate and careful approach to the rationality of retraction for fixed orthopaedic structures.