Benjamin A. Begley
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Benjamin A. Begley has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Victoria Mayne Miller
University of Florida
6 shared publications - Nathan Fripp
Department of Materials Science and Engineering, University of Florida, Gainesville, USA
3 shared publications - Tianchen Wei
Department of Materials Science and Engineering, University of Florida, Gainesville, USA
3 shared publications V. M. Miller
Department of Materials Science and Engineering, University of Florida, Gainesville, USA
2 shared publicationsAdam L. Pilchak
Air Force Research Laboratory, Materials and Manufacturing Directorate, Wright-Patterson AFB, Ohio 45433, USA
1 shared publication- Ahmed Hassen
Manufacturing Science Division Oak Ridge National Laboratory Oak Ridge Tennessee USA
1 shared publication
Latest Publications
- 28 April 2026
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 13 (2) , 516-539
Controlling the Pre-bending Delay During Laser Sheet Metal Forming Under Different Atmospheres
- 28 April 2026
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 13 (2) , 516-539
Controlling the Pre-bending Delay During Laser Sheet Metal Forming Under Different Atmospheres
- 23 December 2025
- Published by Springer Nature in Integrating Materials and Manufacturing Innovation
- Vol. 15 (1) , 18-35
A Multiscale Model Predicting Site-Specific Texture Evolution: Application to Two-Phase Titanium Alloys
- 23 December 2025
- Published by Springer Nature in Integrating Materials and Manufacturing Innovation
- Vol. 15 (1) , 18-35
A Multiscale Model Predicting Site-Specific Texture Evolution: Application to Two-Phase Titanium Alloys
- 13 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (10) , 8941-8952
Laser Bending Behavior of Austenitic Stainless Steels and Characterization of the Resultant Microstructures
- 13 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (10) , 8941-8952
Laser Bending Behavior of Austenitic Stainless Steels and Characterization of the Resultant Microstructures
- 17 October 2024
- Published by Springer Nature in Integrating Materials and Manufacturing Innovation
- Vol. 13 (4) , 883-894
DRAGON: A Tool for Extracting Quantitative Data from Pole Figure Representations of Crystallographic Texture in Literature
- 17 October 2024
- Published by Springer Nature in Integrating Materials and Manufacturing Innovation
- Vol. 13 (4) , 883-894
DRAGON: A Tool for Extracting Quantitative Data from Pole Figure Representations of Crystallographic Texture in Literature
- 20 December 2023
- Published by Springer Nature in JOM
- Vol. 76 (2) , 885-896
Classification of the Mechanisms of Liquid Metal Embrittlement Via Machine Learning
- 20 December 2023
- Published by Springer Nature in JOM
- Vol. 76 (2) , 885-896
Classification of the Mechanisms of Liquid Metal Embrittlement Via Machine Learning
- 3 October 2023
- Published by Springer Nature in Integrating Materials and Manufacturing Innovation
- Vol. 12 (4) , 277-288
VAMPYR: A MATLAB-Based Toolset Leveraging MTEX for Automating VPSC
- 3 October 2023
- Published by Springer Nature in Integrating Materials and Manufacturing Innovation
- Vol. 12 (4) , 277-288
VAMPYR: A MATLAB-Based Toolset Leveraging MTEX for Automating VPSC
- Open Access
Additive Manufacturing of Isotropic NdFeB PPS Bonded Permanent Magnets
Extrusion based additive manufacturing of polymer composite magnets can increase the solid loading volume fraction with greater mechanical force through the printing nozzle as compared to traditional injection molding process. About 63 vol% of isotropic NdFeB magnet powders were compounded with 37 vol% of polyphenylene sulfide and bonded permanent magnets were fabricated while using Big Area Additive Manufacturing without any degradation in magnetic properties. The polyphenylene sulfide bonded magnets have a tensile stress of 20 MPa, almost double than that of nylon bonded permanent magnets. Additively manufactured and surface-protective-resin coated bonded magnets meet the industrial stability criterion of up to 175 °C with a flux-loss of 2.35% over 1000 h. They also exhibit better corrosion resistance behavior when exposed to acidic (pH = 1.35) solution for 24 h and also annealed at 80 °C over 100 h (at 95% relative humidity) over without coated magnets. Thus, polyphenylene sulfide bonded, additively manufactured, protective resin coated bonded permanent magnets provide better thermal, mechanical, and magnetic properties.
Open AccessAdditive Manufacturing of Isotropic NdFeB PPS Bonded Permanent Magnets
Extrusion based additive manufacturing of polymer composite magnets can increase the solid loading volume fraction with greater mechanical force through the printing nozzle as compared to traditional injection molding process. About 63 vol% of isotropic NdFeB magnet powders were compounded with 37 vol% of polyphenylene sulfide and bonded permanent magnets were fabricated while using Big Area Additive Manufacturing without any degradation in magnetic properties. The polyphenylene sulfide bonded magnets have a tensile stress of 20 MPa, almost double than that of nylon bonded permanent magnets. Additively manufactured and surface-protective-resin coated bonded magnets meet the industrial stability criterion of up to 175 °C with a flux-loss of 2.35% over 1000 h. They also exhibit better corrosion resistance behavior when exposed to acidic (pH = 1.35) solution for 24 h and also annealed at 80 °C over 100 h (at 95% relative humidity) over without coated magnets. Thus, polyphenylene sulfide bonded, additively manufactured, protective resin coated bonded permanent magnets provide better thermal, mechanical, and magnetic properties.
- Open Access
- 17 March 2020
- Published by Springer Nature in Journal of Materials Research
- Vol. 35 (8) , 1113-1120
Prediction of relative globularization rates in α + β titanium alloys as a function of initial crystal orientation
- 17 March 2020
- Published by Springer Nature in Journal of Materials Research
- Vol. 35 (8) , 1113-1120
Open AccessPrediction of relative globularization rates in α + β titanium alloys as a function of initial crystal orientation