Aleksandr M. Kislyuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aleksandr M. Kislyuk has a total of 92 co-authors. Here are the top co-authors by number of shared publications:
- Ilya V. Kubasov
Department of Technology of Electronic Materials, Department of Materials Science of Semiconductors and Dielectrics, National University of Science and Technology, «MISIS», 119049 Moscow, Russia
29 shared publications - Andrei Vladimirovich Turutin
Department of Technology of Electronic Materials, Department of Materials Science of Semiconductors and Dielectrics, National University of Science and Technology, «MISIS», 119049 Moscow, Russia
26 shared publications - Mikhail D. Malinkovich
National University of Science and Technology “MISiS”, Moscow, Russia
21 shared publications - Yuriy N. Parkhomenko
National University of Science and Technology “MISiS”, Moscow, Russia
18 shared publications - Alexander A. Temirov
National University of Science and Technology “MISiS”, Moscow, Russia
17 shared publications - Dmitry Anatolyevich Kiselev
National University of Science and Technology MISiS, Moscow, Russia
10 shared publications
Latest Publications
- 11 November 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
Temperature-tuned electrodeposited CoNiP as an internal bias layer for self-biased LiNbO 3 /Metglas DC magnetic-field sensor
Electrodeposited CoNiP is investigated as a material for a remanent magnetic biasing layer for self-biased magnetoelectric sensors. CoNiP coatings were deposited from a sulfate-hypophosphite electrolyte at temperatures between 40 and 55 °C while the remaining deposition parameters were held constant. Raising the electrolyte temperature resulted in an increase in the phosphorus concentration from 3.1 to 13.5 at.%, accompanied by a transition from an acicular crystalline morphology to a finer and more structurally disordered morphology. The in-plane coercive field decreased from 618 to 260 Oe, while the saturation magnetization decreased from 101.1 to 57.2 emu/g. The coating deposited at 40 °C, which exhibited the highest coercivity and magnetization, was used as a magnetization layer in an magnetoelectric (ME) composite structure based on a y+128°-cut bidomain LiNbO3 plate and 1K101 Metglas to form a self-biased laminate. Two flexural resonances were observed at 465 and 3393 Hz, with magnetoelectric coefficients of 193 and 117 V/(cm·Oe), respectively. A modulation frequency of 3396 Hz was selected because it combined a high magnetoelectric response with a low equivalent electric noise level. At zero external bias, the laminate exhibited a magnetoelectric coefficient of 103.3 V/(cm·Oe) at the modulation frequency and an approximately linear response from −1.10 to +1.04 Oe for a 10% nonlinearity criterion. The DC magnetic-field sensitivity was 17.6·103 V/T, corresponding to a limit of detection (LOD) of 40 pT/Hz1/2. Time-domain measurements resolved 2 nT DC magnetic field steps. These results demonstrate that electrodeposited CoNiP can provide stable internal magnetic biasing for compact magnetoelectric sensors operating without an external DC-bias magnet.
- 11 November 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
Temperature-tuned electrodeposited CoNiP as an internal bias layer for self-biased LiNbO 3 /Metglas DC magnetic-field sensor
Electrodeposited CoNiP is investigated as a material for a remanent magnetic biasing layer for self-biased magnetoelectric sensors. CoNiP coatings were deposited from a sulfate-hypophosphite electrolyte at temperatures between 40 and 55 °C while the remaining deposition parameters were held constant. Raising the electrolyte temperature resulted in an increase in the phosphorus concentration from 3.1 to 13.5 at.%, accompanied by a transition from an acicular crystalline morphology to a finer and more structurally disordered morphology. The in-plane coercive field decreased from 618 to 260 Oe, while the saturation magnetization decreased from 101.1 to 57.2 emu/g. The coating deposited at 40 °C, which exhibited the highest coercivity and magnetization, was used as a magnetization layer in an magnetoelectric (ME) composite structure based on a y+128°-cut bidomain LiNbO3 plate and 1K101 Metglas to form a self-biased laminate. Two flexural resonances were observed at 465 and 3393 Hz, with magnetoelectric coefficients of 193 and 117 V/(cm·Oe), respectively. A modulation frequency of 3396 Hz was selected because it combined a high magnetoelectric response with a low equivalent electric noise level. At zero external bias, the laminate exhibited a magnetoelectric coefficient of 103.3 V/(cm·Oe) at the modulation frequency and an approximately linear response from −1.10 to +1.04 Oe for a 10% nonlinearity criterion. The DC magnetic-field sensitivity was 17.6·103 V/T, corresponding to a limit of detection (LOD) of 40 pT/Hz1/2. Time-domain measurements resolved 2 nT DC magnetic field steps. These results demonstrate that electrodeposited CoNiP can provide stable internal magnetic biasing for compact magnetoelectric sensors operating without an external DC-bias magnet.
- Open Access
- 7 October 2026
- Published by MDPI AG in Nanomaterials
- Vol. 16 (19) , 1262
RETRACTED: Tishkevich et al. Magnetic Properties of the Densely Packed Ultra-Long Ni Nanowires Encapsulated in Alumina Membrane. Nanomaterials 2021, 11, 1775
The journal retracts the article “Magnetic Properties of the Densely Packed Ultra-Long Ni Nanowires Encapsulated in Alumina Membrane”
- 7 October 2026
- Published by MDPI AG in Nanomaterials
- Vol. 16 (19) , 1262
Open AccessRETRACTED: Tishkevich et al. Magnetic Properties of the Densely Packed Ultra-Long Ni Nanowires Encapsulated in Alumina Membrane. Nanomaterials 2021, 11, 1775
The journal retracts the article “Magnetic Properties of the Densely Packed Ultra-Long Ni Nanowires Encapsulated in Alumina Membrane”
- Open Access
- 18 April 2026
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 12 (1) , 3-16
Performance of ITO, NiCr, and Pd thick film electrodes on lithium niobate under high-temperature operation
Reliable electrical contacts are essential for high-temperature piezoelectric devices based on lithium niobate (LiNbO 3 , LN), yet the behavior of electrode materials under elevated temperatures remains insufficiently studied. Here we evaluate three practical electrode systems on bidomain LN (BLN) substrates: screen-printed Pd thick films, sputtered indium–tin oxide (ITO), and sputtered nichrome (80 wt.% Ni and 20 wt.% Cr). Bidomain LN crystals function as single-crystal piezoelectric bimorphs with well-defined bending resonances, enabling sensitive impedance-based detection of electrode degradation. Impedance spectra were recorded in 100 °C increments up to 800 °C, complemented by microstructural inspection, electrical resistivity measurements, and X-ray photoelectron spectroscopy. Pd thick films showed the highest stability, with unchanged impedance spectra after heating to 800 °C and cooling. Indium–tin oxide electrodes remained functional up to at least 700 °C, with possible operation at 800 °C. X-ray photoelectron spectroscopy results suggest gradual incorporation of Nb from the BLN substrate which may initiate slow degradation in ITO. NiCr electrodes showed degradation of electrical contact near 500 °C due to oxide formation, while intrinsic electrical degradation associated with loss of film continuity occurred above 600 °C. These results identify Pd as a robust but costly choice, ITO as a promising mid-range alternative, and NiCr as suitable only within a lower high-temperature window.
- 18 April 2026
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 12 (1) , 3-16
Open AccessPerformance of ITO, NiCr, and Pd thick film electrodes on lithium niobate under high-temperature operation
Reliable electrical contacts are essential for high-temperature piezoelectric devices based on lithium niobate (LiNbO 3 , LN), yet the behavior of electrode materials under elevated temperatures remains insufficiently studied. Here we evaluate three practical electrode systems on bidomain LN (BLN) substrates: screen-printed Pd thick films, sputtered indium–tin oxide (ITO), and sputtered nichrome (80 wt.% Ni and 20 wt.% Cr). Bidomain LN crystals function as single-crystal piezoelectric bimorphs with well-defined bending resonances, enabling sensitive impedance-based detection of electrode degradation. Impedance spectra were recorded in 100 °C increments up to 800 °C, complemented by microstructural inspection, electrical resistivity measurements, and X-ray photoelectron spectroscopy. Pd thick films showed the highest stability, with unchanged impedance spectra after heating to 800 °C and cooling. Indium–tin oxide electrodes remained functional up to at least 700 °C, with possible operation at 800 °C. X-ray photoelectron spectroscopy results suggest gradual incorporation of Nb from the BLN substrate which may initiate slow degradation in ITO. NiCr electrodes showed degradation of electrical contact near 500 °C due to oxide formation, while intrinsic electrical degradation associated with loss of film continuity occurred above 600 °C. These results identify Pd as a robust but costly choice, ITO as a promising mid-range alternative, and NiCr as suitable only within a lower high-temperature window.
- 26 November 2025
- Published by Elsevier in Measurement
- Vol. 260
Double-crystal monochromator with adaptive X-ray optical elements for synchrotron studies of materials with temporal resolution
- 26 November 2025
- Published by Elsevier in Measurement
- Vol. 260
Double-crystal monochromator with adaptive X-ray optical elements for synchrotron studies of materials with temporal resolution
- 24 November 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (47) , 475303
Decoupling activation energies of bulk and charged domain wall conductivity in reduced lithium niobate
Charged domain walls (CDWs) in ferroelectrics exhibit enhanced and tunable conductivity, making them attractive for devices such as non-volatile memories, memristors, and hybrid electro-optic-mechanical systems. Most previous studies of CDWs in lithium niobate (LiNbO 3 ) have focused on Mg-doped crystals. Here, we investigate an extended head-to-head CDW with an inclination angle close to 90°, formed in nominally pure congruent LiNbO 3 during high-temperature reduction annealing near the Curie point. The electrophysical properties of such reduced bidomain crystals, where the bulk shows mixed free- and bound-polaron transport, remain largely unexplored. We systematically measured temperature-dependent current–voltage characteristics from room temperature up to 60 °C using planar structure with Ti electrodes. Data were acquired separately on electrodes contacting the single-domain bulk and those intersecting the CDW (where the measured current is a sum of the CDW and the surrounding single-domain conductivity). Applying the R2D2 equivalent-circuit model enabled us to isolate the intrinsic conductivity of the CDW itself from the parallel conduction channel of the adjacent single-domain matrix. The analysis revealed a stark contrast in activation energies. In the bulk, it was ≈0.5 eV, attributed to bound-polaron hopping. At the CDW, however, the activation energy was not only significantly lower but also exhibited a pronounced polarity dependence: 0.13 eV for one voltage bias and 0.20 eV for the opposite polarity. This anisotropy and the suppression of the activation energy are consistent with a high-density free-polaron gas near the wall, where strong mutual repulsion between carriers reduces the energy barrier for charge transport. Independent determination of currents and activation energies for bulk and domain walls provides new insight into charge-transport mechanisms in ferroelectrics and highlights the potential of domain-wall engineering for future nanoelectronics applications.
- 24 November 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (47) , 475303
Decoupling activation energies of bulk and charged domain wall conductivity in reduced lithium niobate
Charged domain walls (CDWs) in ferroelectrics exhibit enhanced and tunable conductivity, making them attractive for devices such as non-volatile memories, memristors, and hybrid electro-optic-mechanical systems. Most previous studies of CDWs in lithium niobate (LiNbO 3 ) have focused on Mg-doped crystals. Here, we investigate an extended head-to-head CDW with an inclination angle close to 90°, formed in nominally pure congruent LiNbO 3 during high-temperature reduction annealing near the Curie point. The electrophysical properties of such reduced bidomain crystals, where the bulk shows mixed free- and bound-polaron transport, remain largely unexplored. We systematically measured temperature-dependent current–voltage characteristics from room temperature up to 60 °C using planar structure with Ti electrodes. Data were acquired separately on electrodes contacting the single-domain bulk and those intersecting the CDW (where the measured current is a sum of the CDW and the surrounding single-domain conductivity). Applying the R2D2 equivalent-circuit model enabled us to isolate the intrinsic conductivity of the CDW itself from the parallel conduction channel of the adjacent single-domain matrix. The analysis revealed a stark contrast in activation energies. In the bulk, it was ≈0.5 eV, attributed to bound-polaron hopping. At the CDW, however, the activation energy was not only significantly lower but also exhibited a pronounced polarity dependence: 0.13 eV for one voltage bias and 0.20 eV for the opposite polarity. This anisotropy and the suppression of the activation energy are consistent with a high-density free-polaron gas near the wall, where strong mutual repulsion between carriers reduces the energy barrier for charge transport. Independent determination of currents and activation energies for bulk and domain walls provides new insight into charge-transport mechanisms in ferroelectrics and highlights the potential of domain-wall engineering for future nanoelectronics applications.
- Open Access
- 30 December 2024
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 10 (4) , 227-241
Bending dynamics of bidomain LiNbO3 single-crystalline bimorphs
This study examines the bending dynamics of cantilevered single-crystalline bimorphs made from bidomain LiNbO3 (BLN), emphasizing the interaction between bending resonances, antiresonances, and torsional vibrations. Combining theoretical modeling and experimental validation, we demonstrate that a 1D analytical model, based on classical beam theory, surpasses FEM modeling in predicting bending resonances, particularly in the low-frequency range. The analytical model provides precise positioning of resonant frequencies, enabling the strategic alignment of torsional resonances with bending antiresonances, as confirmed experimentally. Our findings underscore the high predictability of BLN-based bimorphs, allowing accurate descriptions of their behavior at bending resonances, antiresonances, and piezoelectrically passive torsional resonances. Unlike glued actuators made of lead-based ceramics, BLN bimorphs offer superior thermal stability, long-term reliability, and predictable performance. These properties, combined with the availability of commercially produced LN crystals, position BLN-based bimorphs as ideal candidates for MEMS applications, enabling advanced sensing and actuation solutions with reduced reliance on complex feedback loops.
- 30 December 2024
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 10 (4) , 227-241
Open AccessBending dynamics of bidomain LiNbO3 single-crystalline bimorphs
This study examines the bending dynamics of cantilevered single-crystalline bimorphs made from bidomain LiNbO3 (BLN), emphasizing the interaction between bending resonances, antiresonances, and torsional vibrations. Combining theoretical modeling and experimental validation, we demonstrate that a 1D analytical model, based on classical beam theory, surpasses FEM modeling in predicting bending resonances, particularly in the low-frequency range. The analytical model provides precise positioning of resonant frequencies, enabling the strategic alignment of torsional resonances with bending antiresonances, as confirmed experimentally. Our findings underscore the high predictability of BLN-based bimorphs, allowing accurate descriptions of their behavior at bending resonances, antiresonances, and piezoelectrically passive torsional resonances. Unlike glued actuators made of lead-based ceramics, BLN bimorphs offer superior thermal stability, long-term reliability, and predictable performance. These properties, combined with the availability of commercially produced LN crystals, position BLN-based bimorphs as ideal candidates for MEMS applications, enabling advanced sensing and actuation solutions with reduced reliance on complex feedback loops.
- Open Access
- 30 December 2024
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 10 (4) , 217-226
Charge carrier distribution in the region of charged domain walls in reduced lithium niobate
Charged domain walls (CDWs) in ferroelectric materials are of interest from both fundamental and applied perspectives due to their unique electrophysical properties, which differ significantly from those of the bulk material. Until recently, research efforts primarily focused on studying these properties, while less attention was given to the finite-thickness regions of CDWs with heterogeneous electrical conductivity. This study proposes a model describing the charge carrier distribution within the conductive region of CDWs. The dependencies of charge carrier concentration and mobility on the distance from the CDW were determined. An analytical expression for current-voltage characteristics, measurable by conductive atomic force microscopy (c-AFM), was also proposed. The model has been experimentally validated using AFM methods. In particular, the Debye screening length of the electric field of head-to-head (H–H) CDWs by free charge carriers in strongly reduced LiNbO3 crystals was found to be 90±10 nm. Additionally, the values of mobility and concentration of polarons forming the conductive H–H CDW were determined. The bound polaron concentration in this region is estimated to be approximately 30 times greater than in the monodomain region, reaching ≈3.8·1017 cm-3.
- 30 December 2024
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 10 (4) , 217-226
Open AccessCharge carrier distribution in the region of charged domain walls in reduced lithium niobate
Charged domain walls (CDWs) in ferroelectric materials are of interest from both fundamental and applied perspectives due to their unique electrophysical properties, which differ significantly from those of the bulk material. Until recently, research efforts primarily focused on studying these properties, while less attention was given to the finite-thickness regions of CDWs with heterogeneous electrical conductivity. This study proposes a model describing the charge carrier distribution within the conductive region of CDWs. The dependencies of charge carrier concentration and mobility on the distance from the CDW were determined. An analytical expression for current-voltage characteristics, measurable by conductive atomic force microscopy (c-AFM), was also proposed. The model has been experimentally validated using AFM methods. In particular, the Debye screening length of the electric field of head-to-head (H–H) CDWs by free charge carriers in strongly reduced LiNbO3 crystals was found to be 90±10 nm. Additionally, the values of mobility and concentration of polarons forming the conductive H–H CDW were determined. The bound polaron concentration in this region is estimated to be approximately 30 times greater than in the monodomain region, reaching ≈3.8·1017 cm-3.
- Open Access
- 12 December 2023
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 9 (4) , 177-184
Synthesis of silicon-carbon films by induction-assisted plasma-chemical deposition
Silicon-carbon films are of great interest as diamond-like materials combining unique properties, e.g. high hardness, adhesion to a wide range of materials, abrasion resistance, chemical resistance, low friction coefficient and biocompatibility. The presence of silicon in the films significantly reduces their inner mechanical stress as compared to diamond films. Currently, the films are used in industry, primarily, as solid lubricants and protective coatings. There are a large number of silicon-carbon film synthesis methods the most widely used of which are various options of chemical vapor deposition. A new silicon-carbon film synthesis technique has been suggested and tested. The technique is based on the use of high-frequency induction for obtaining plasma of silicon and carbon vapors supplied to the reaction chamber from an external source. Impurity-free silicon-carbon films containing 63–65 % carbon atoms with sp3 orbital hybridization have been synthesized on Sitall substrates. The composition, surface roughness and friction coefficient of the impurity-free silicon-carbon films synthesized using the suggested technology have been studied. The possibility of implementing resistive switching in thin silicon-carbon films in cross-bar structures with metallic electrodes has been analyzed.
- 12 December 2023
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 9 (4) , 177-184
Open AccessSynthesis of silicon-carbon films by induction-assisted plasma-chemical deposition
Silicon-carbon films are of great interest as diamond-like materials combining unique properties, e.g. high hardness, adhesion to a wide range of materials, abrasion resistance, chemical resistance, low friction coefficient and biocompatibility. The presence of silicon in the films significantly reduces their inner mechanical stress as compared to diamond films. Currently, the films are used in industry, primarily, as solid lubricants and protective coatings. There are a large number of silicon-carbon film synthesis methods the most widely used of which are various options of chemical vapor deposition. A new silicon-carbon film synthesis technique has been suggested and tested. The technique is based on the use of high-frequency induction for obtaining plasma of silicon and carbon vapors supplied to the reaction chamber from an external source. Impurity-free silicon-carbon films containing 63–65 % carbon atoms with sp3 orbital hybridization have been synthesized on Sitall substrates. The composition, surface roughness and friction coefficient of the impurity-free silicon-carbon films synthesized using the suggested technology have been studied. The possibility of implementing resistive switching in thin silicon-carbon films in cross-bar structures with metallic electrodes has been analyzed.
- Open Access
- 12 December 2023
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 9 (4) , 145-161
Electrophysical properties, memristive and resistive switching of charged domain walls in lithium niobate
Charged domain walls (CDWs) in ferroelectric materials raise both fundamental and practical interest due to their electrophysical properties differing from bulk ones. On a microstructure level, CDWs in ferroelectrics are 2D defects separating regions with different spontaneous polarization vector directions. Screening of electric field of the CDW's bound ionic charges by mobile carriers leads to the formation of elongated narrow channels with an elevated conductivity in initially dielectric materials. Controlling the position and inclination angle of CDW relative to the spontaneous polarization direction, one can change its conductivity over a wide range thus providing good opportunities for developing memory devices, including neuromorphic systems. This review describes the state of art in the formation and application of CDWs in single crystal uniaxial ferroelectric lithium niobate (LiNbO3, LN), as resistive and memristive switching devices. The main CDWs formation methods in single crystal and thin-film LN have been described, and modern data have been presented on the electrophysical properties and electrical conductivity control methods of CDWs. Prospects of CDWs application in resistive and memristive switching memory devices have been discussed.
- 12 December 2023
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 9 (4) , 145-161
Open AccessElectrophysical properties, memristive and resistive switching of charged domain walls in lithium niobate
Charged domain walls (CDWs) in ferroelectric materials raise both fundamental and practical interest due to their electrophysical properties differing from bulk ones. On a microstructure level, CDWs in ferroelectrics are 2D defects separating regions with different spontaneous polarization vector directions. Screening of electric field of the CDW's bound ionic charges by mobile carriers leads to the formation of elongated narrow channels with an elevated conductivity in initially dielectric materials. Controlling the position and inclination angle of CDW relative to the spontaneous polarization direction, one can change its conductivity over a wide range thus providing good opportunities for developing memory devices, including neuromorphic systems. This review describes the state of art in the formation and application of CDWs in single crystal uniaxial ferroelectric lithium niobate (LiNbO3, LN), as resistive and memristive switching devices. The main CDWs formation methods in single crystal and thin-film LN have been described, and modern data have been presented on the electrophysical properties and electrical conductivity control methods of CDWs. Prospects of CDWs application in resistive and memristive switching memory devices have been discussed.